GE NetworX NX-6 Installation And Startup page 16

Table 1.1
Segment 1
1
2
3
4
5
6
7
8
Segment 2
1
2
3
4
5
6
7 & 8
LOCATION 5 PARTITIONS REPORTED TO PHONE #1
Location 5 is used when events to be reported to a phone number are based upon the partition regardless of the event.
Program a A1" for Partition 1, and a A2" for Partition 2.
LOCATION 6
PROGRAMMING PHONE #2
Phone #2 is programmed in location 6. A "14" indicates the end of the phone number. Delays of four seconds can be
programmed at any point in the phone number by programming a "13" in the appropriate segment. If tone dialing is
desired, program a "15" in the segment where tone dialing should begin. If the entire number should be tone dialing,
program a "15" in the first segment. Program an A11" for a Ar@, and a A12" for a A#@. Caution: A call-waiting cancel on a
non- call waiting line will prevent successful connection to the central station.
LOCATION 7
ACCOUNT CODE FOR THE PHONE #2
The account code sent when Phone #2 is dialed is programmed in location 7.
immediately after the last digit of the account code. If the account code is 6 digits long, program all 6 segments. If this
location is left unprogrammed, account code 1 will be used when the second phone number is dialed.
LOCATION 8 COMMUNICATOR FORMAT FOR PHONE # 2
Location 8 contains the communicator format used to transmit to the receiver connected to Phone #2. Consult the
instruction manual for your central station receiver to determine which format is compatible, and select from the 15
formats listed on page 13. If you require a format other than those listed, review the override options described in
Location 18 to build the appropriate format. A "15" must be programmed in location 8 in addition to the entries in
location 18 in order to create a special format. If this location contains a "0", format 1 will be used when Phone #2 is
dialed.
LOCATION 9 DIAL ATTEMPTS/BACKUP CONTROL PHONE #2
Segment 1 Dial attempts: Segment 1 of Location 9 is used to enter the number of dial attempts (1 to 15 attempts)
the communicator will make to Phone #2 before ending the notification process.
communicator will make the same number of attempts as those programmed in location 3.
Segment 2 Phone #2 Backup Control: Programming a "0" in Segment 2 of this location will cause the NX-6 to
make the designated number of attempts to Phone #2 and #1 before setting the "Fail To Communicate" condition and
stop reporting. Programming a "1" in this segment will cause the NX-6 to stop trying to communicate after the
designated number of attempts have been made to Phone #2. If a "2" is programmed in this segment, it will cause the
NX-6 to make the dial attempts in increments of two. The first two attempts will be made to Phone #2, the next two
attempts to Phone #1, then repeating until the total number of attempts designated in Segment 1 is completed.
Page 14
Alarms and Alarm Restores
Opening and Closings
Zone Bypass and Bypass Restores
Zone Trouble and Trouble Restores
Power Fail, Low Battery, Power Restore, and Low Battery Restore
Bell Cut , Telephone Line Cut, Bell Cut Restore, Telephone Line Restore
Test Reports
Start and End programming, Download complete
Zone and Box Tamper and Tamper Restore
Auxiliary Power Overcurrent and Restore
Wireless Sensor Missing and Restore
Wireless Sensor Low Battery and Restore
Expander Trouble and Restore
Fail To Communicate
Reserved
If this location is used, location 4 should be "0".
1 segment, feature selection
20 segments, numerical data
6 segments of numerical data
Program a A10" in the segment
1 segment, numerical data
2 segments, numerical data
Factory default is "0" and the