ETC Source Four Zoom User Manual
  1. Manuals
  2. Brands
  3. ETC Manuals
  4. Lighting Equipment
  5. Source Four Zoom
  6. User manual
ETC Source Four Zoom User Manual

ETC Source Four Zoom User Manual

Hide thumbs Also See for Source Four Zoom:
Table of Contents

Advertisement

Quick Links

Zoom

User Manual

Production Dates: September 2004 - Present
C o p y r i g h t © E l e c t r o n i c 2 0 0 8 T h e a t r e C o n t r o l s , I n c .
A l l R i g h t s r e s e r v e d .
P r o d u c t in f o r m a t i on a n d s p e c i f i c a t i o n s s u bj e c t t o c h a n g e .
P a r t N u m b e r : 7060M1250-06.01 R e v C
R e l e as e d : J a n u a r y 2 0 1 0
P i c k i n g # 7 0 6 0 M 1 0 0 8 - C

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Source Four Zoom and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for ETC Source Four Zoom

Summary of Contents for ETC Source Four Zoom

  • Page 1: User Manual

    Zoom User Manual Production Dates: September 2004 - Present C o p y r i g h t © E l e c t r o n i c 2 0 0 8 T h e a t r e C o n t r o l s , I n c . A l l R i g h t s r e s e r v e d .

  • Page 2: Table Of Contents

    T a b l e o f C o n t e n t s Basic Assembly .........1 Fixture information .

  • Page 3: Basic Assembly

    Basic Assembly Insulated handle Yoke Lamp housing Retainer bolt Barrel Pattern holder slot Drop-in iris slot Optional Color frame Balancing yoke retaining gel clip Reflector housing Yoke locking knob 15°-30° lens tube Barrel rotation knob Shutters Focus dial 25°-50° lens tube Color frame Figure 1 W A R N I N G :...

  • Page 4: Fixture Information

    3,200°K 300 hours HPL 750/240X 15,600 3,050°K 1500 hours HPL 575/240 14,900 3,050°K 400 hours HPL 575/240X 11,780 3,050°K 1500 hours HPL 375/240X 7,250 3,000°K 1000 hours * To be used with ETC Dimmer Doubler™ Source Four Zoom User Manual...

  • Page 5: Color Frame Holder

    750w lamp. For best results, always use high-quality color media rated for high-temperature use. ETC’s optional Gel Extender, part # PSF1029, will provide maximum color media life. The use of any gel extender accessory may limit the coverage of any wide- angle lens or beam setting.

  • Page 6: Replacing The Hpl Lamp

    Improperly installed lamps cause premature lamp failure and socket problems. Step 6: Press lamp retaining clip across lamp base to secure. Step 7: Reinstall the lamp housing by aligning the bolt hole and tightening the knurled bolt. Source Four Zoom User Manual...

  • Page 7: Adjustments

    Adj ustments C e n t e r i n g l a m p a n d a d j u s t i n g t h e f i e l d Flat field-best adjustment Rear lamp Inner Knob - housing peak/flat field...

  • Page 8: Shaping The Beam

    Figure 7 3.70" N o t e : Because the Source Four aperture is 3 inches wide, ETC recommends using A-size patterns for maximum pattern effectiveness. Use an optional donut in the accessory holder to enhance pattern projection. Donut diameter range should be 2.5”...

  • Page 9: Rotating The Barrel Assembly

    Step 4: Slide the slot cover back toward the shutters until it meets the iris handle. Leave enough space to move the iris handle. Step 5: Secure the drop-in iris slot cover by tightening the screws. R o t a t i n g t h e b a r r e l a s s e m b l y Barrel rotation knob Figure 9...

  • Page 10: Adjusting The Yoke Position - 25°-50° Zoom

    Yoke locking knob Step 1: Loosen the yoke locking knobs (see Figure 12). Do not remove them. Step 2: Tilt the fixture to the desired position. Step 3: Tighten the yoke locking knobs to secure in position. Source Four Zoom User Manual...

  • Page 11: Adjusting The Optional Balance Yoke Position - 15°-30° Zoom

    A d j u s t i n g t h e o p t i o n a l b a l a n c e y o k e p o s i t i o n — 1 5 ° - 3 0 ° Z o o m The Source Four 15°-30° Zoom has an optional balance yoke bracket (ETC part # 7060A2028) for repositioning the fixture’s center of gravity.

  • Page 12: Cleaning Lens And Reflector

    Remove dust with a blast of oil-free air or wipe with a clean, lint-free cloth. Isopropyl alcohol, distilled water or a 50%-50% mixture of each can be used to clean the glass surface. Step 4: Close the extrusion door and turn the fastener 1/4 turn to secure it. Source Four Zoom User Manual...

  • Page 13: Cleaning The Reflector

    C l e a n i n g t h e r e f l e c t o r W A R N I N G : Unplug the fixture before attempting to clean the reflector. To quickly clean the reflector, remove the lens tube and clean the dust from the reflector with a blast of oil-free air.
  • Page 14 Source Four Zoom User Manual...
  • Page 15 Cleaning Lens and Reflector...
  • Page 16    Service: (Americas) service@etcconnect.com (UK) service@etceurope.com (DE) techserv-hoki@etcconnect.com (Asia) service@etcasia.com    Web: www.etcconnect.com Copyright © 2008 ETC. All Rights Reserved. Product information and specifications subject to change.   7060M1250-06.01 Rev C Released 2010-01  ...

Table of Contents