ETC Source Four Zoom Assembly Manual
Hide thumbs
Also See for Source Four Zoom:
- User manual (16 pages) ,
- Assembly manual (20 pages) ,
- Assembly manual (20 pages)
Related Manuals for ETC Source Four Zoom
Summary of Contents for ETC Source Four Zoom
- Page 1 Source Four Zoom Assembly Guide Production Dates: September 2004–Present Part Number: 7060M2550-06.01 Rev: B Released: 2019-08...
- Page 2 To view a list of ET C tr ad e m a r k s a n d p a t e n t s , g o t o etcconnect.com/ip. A l l o t h e r t r a d e m a r k s , b o t h m a r k e d a n d no t m a r k e d , a r e t h e p r o p ert y o f t h ei r r es p e c ti v e o w ne r s .
-
Page 3: Table Of Contents
Document Conventions.......1 Help from ETC Technical Services ..... . .2 15°–30°... - Page 4 Source Four Zoom Assembly Guide...
-
Page 5: Introduction
WARNING: RISK OF ELECTRIC SHOCK! This warning statement indicates situations where there is a risk of electric shock. All ETC documents are available for free download from our website: etcconnect.com. Please email comments about this manual to: TechComm@etcconnect.com. Introduction... -
Page 6: Help From Etc Technical Services
Help from ETC Technical Services If you are having difficulties, and your problem is not addressed by this document, try the ETC support website at support.etcconnect.com or the main ETC website at etcconnect.com. If none of these resources are sufficient, contact ETC Technical Services directly at one of the offices identified below. -
Page 7: 15°-30° Basic Fixture
15°–30° Basic Fixture Figure 1 Reference Part Quantity Description Number Number Required 7060A2030 15°–30° lens tube 7060A2020 Reflector housing assembly, double clutch 7060A2008 Lamp socket assembly 7060A4008-01 Knob set with male insert 7060A4037 Handle, insulated rear HW5197 Screw, 1/4-20 x 5/8, black zinc HW2181 Screw, 6-32 x 3/4, black Taptite page 11... -
Page 8: 25°-50° Basic Fixture
Release the gel retaining clip by pushing it sideways while gently pulling backwards. Insert the color frame. Lock the clip by pushing sideways while gently pushing it forward. Source Four Zoom Assembly Guide... -
Page 9: Lamp Socket Assembly
Lamp Socket Assembly Figure 3 Reference Part Quantity Description Number Number Required 7060A3055 Housing, socket, casting, painted 7060A3007 Socket, light baffle casting, raw 7060A4007 Knob, X-Y, lamp set 7060A4008-02 Knob, Z, lamp set w/female insert 7060A4011 Bushing, cup 7060A3011 Hub, index, casting 7060A3012 Spring, lamp retainer HW748... -
Page 10: Assemble Lamp Socket
Note: If the spring does not seat correctly, coax it into place with a screwdriver or needle- nose pliers. Source Four Zoom Assembly Guide... - Page 11 Figure 6 Install the bushing cup (5) into the housing socket casting (1) as shown in Figure 6 . The cup should slide smoothly up and down, but not side to side. Insert the threaded end of the index hub (6) through the holes in the bushing cup and the back of the housing socket casting (1).
- Page 12 (15), then install the X-Y lampset (3) and Z lamp knob (4). Hand tighten the knob all the way to the right. CAUTION: You must install Z knob as described above to ensure proper lamp focus travel. Source Four Zoom Assembly Guide...
-
Page 13: Reflector Housing Assembly
Reflector Housing Assembly (4 required) (2 required) (4 required) (4 required) Figure 9 Reference Part Quantity Description Number Number Required 7060A3054 Housing, reflector casting, painted black 7060A3006 Clip, reflector retainer 7060A4010 Bushing, gate 7060A3016 Plate, clutch 7060A3019 Spring, reflector support 7060A4015 Reflector, molded glass, coated 7060A3058... -
Page 14: Installing Reflector
Remove dust with a blast of oil-free air or wipe with a clean, lint-free cloth. Isopropyl alcohol, distilled water or a 50%-50% mixture of each can be used to clean the glass surface. Source Four Zoom Assembly Guide... -
Page 15: Front Barrel Assembly
Front Barrel Assembly Figure 11 See detail to the right Shutter Assembly: The bottom divider plate (4) has four dimples punched into the surface; the top plate (6) has none. The middle divider plates (5) are noticeably thinner-gauge metal than the other two. -
Page 16: Assemble Front Barrel Assembly
Connect the halves of the gate assembly using two PHMS screws (8). Hand tighten only (25 inch pounds). Note: The tops of the two front barrel castings must be even. Adjust as necessary before completely tightening the screws. Failure to do this could interfere with the barrel rotation. Source Four Zoom Assembly Guide... - Page 17 Turn the front barrel assembly over so that the narrower end is on your work surface. Install the four shutter springs (7) between the four dimples in the shutter plate and the tabs in the lip of the casting. Note: Install the springs at the joints in the castings on either of the tabs at the joint.
-
Page 18: 15°-30° Lens Tube
15°–30° Lens Tube Front Barrel Assembly page 11 15°–30° Lens tube assembly Figure 12 15°–30° Gel frame endcap assembly Figure 13 15°–30° Front lens assembly Figure 14 15°–30° Rear lens assembly Figure 15 Source Four Zoom Assembly Guide... -
Page 19: 15°-30° Lens Tube Assembly
15°–30° Lens tube assembly Reference Part Quantity Description Number Number Required 7060A2030 15°–30° lens tube 7060A3091-01 Extrusion door See below Front lens assembly See below Rear lens assembly HW5218 Nut, 1/4-20 metal lock Lowpro 7060A4056 Dial adjustment 7060A4066 Button, push, CAM lever HW776 Spring, push-button 7060A4057... -
Page 20: 25°-50° Lens Tube
25°–50° Lens Tube Front Barrel Assembly page 11 25°–50° Lens tube assembly Figure 16 25°–50° Gel frame endcap assembly Figure 17 25°–50° Front lens assembly Figure 18 25°–50° Rear lens assembly Figure 19 Source Four Zoom Assembly Guide... -
Page 21: 25°-50° Lens Tube Assembly
25°–50° lens tube assembly Reference Part Quantity Description Number Number Required 7060A2032 25°–50° lens tube 7060A3139-02 Extrusion door See below Front lens assembly See below Rear lens assembly HW5218 Nut, 1/4-20 metal lock Lowpro 7060A4056 Dial adjustment 7060A4066 Button, push, CAM lever HW776 Spring, push-button 7060A4057... -
Page 22: Assemble Lens Tube (15°-30° And 25°-50°)
With the extrusion door open, place the gel cap (19) on the front of the unit and secure with four screws (20). Once the gel cap is in place, close the extrusion door and turn the fastener (18) one-quarter turn clockwise to secure the baffle in place. Source Four Zoom Assembly Guide... -
Page 23: Cleaning Glass Lens
Cleaning glass lens WARNING: Do not use ammonia-based or other harsh commercial cleaners. Clean lens only as directed. Commercially available glass cleaning agents should be avoided as they may contain ammonia, other harsh chemical detergents or abrasive agents. These cleaners may damage the glass surface and the Anti-Reflective coatings. Do not immerse or soak the glass in any cleaning solution. - Page 24 Holzkirchen, DE +49 (80 24) 47 00-0 Rome, IT +39 (06) 32 111 683 Hong Kong +852 2799 1220 Paris, FR +33 1 4243 3535 etcconnect.com Support support.etcconnect.com Contact etcconnect.com/contactETC © 2019 Electronic Theatre Controls, Inc. Trademark and patent info: etcconnect.com/ip Product information and specifications subject to change. ETC intends this document to be provided in its entirety. 7060M2550-06.01 Rev B Released 2019-08...