Table of Contents
Advertisement
[B211] ADJUST menu (STD/COL1/COL2)
To start adjustment, proceed as follows.
When you use the previously adjusted values for
adjustment, you can make start adjustment by selecting
START without perform operations step (1) and step
(2).
(1) Select either D65 or D93.
Rather than selecting D65 or D93, you may instead
enter the values of the CIE 1931 color system x
and y coordinates.
(2) Enter values for LOWLIGHT and HIGHLIGHT.
(3) Select START.
START: Start adjustment. ÷[B2111]
X: Enter the x coordinate.
Y: Enter the y coordinate.
LOW LIGHT (20IRE): Enter the luminance (cd/m
2
)
for low light.
HIGH LIGHT (100IRE): Enter the luminance (cd/
2
m
) for high light.
D65: Use D65 setting.
D93: Use D93 setting.
[B212] ANALYZE menu (STD/COL1/COL2)
The following message appears. Perform operation
according to the message to enable the BKM-14L to
read the color system and luminace value.
SET PROBE ON THIS CRT
PRESS ENTER
Attach the BKM-14L on the center of the CRT and
press the ENTER button. ÷[B2121]
Once the BKM-14L has carried out calibration, the
BKM-14L can start analyze the monitor's
performance.
[B321] MONITOR ADDRESS menu (STD/COL1/
COL2)
Select STD, COL1 or COL2. ÷ Copy is carried out.
STD: Copy common data (factory setting: D93).
COL1: Copy common data (factory setting: D65).
COL2: Copy common data (factory setting: D93).
[B331] FILE NAME menu (STD/COL1/COL2)
Select STD, COL1, or COL2 of the memory card data.
÷ Copy is carried out.
STD: Copy common data (factory setting: D93).
COL1: Copy common data (factory setting: D65).
COL2: Copy common data (factory setting: D93).
[B2111] COLOR TEMP ADJ menu
(STD/COL1/COL2)
The following message appears. Perform operation
according to the message to start adjustment.
SET PROBE ON CRT
PRESS ENTER
Adjustment starts when the probe is placed against the
center of the screen and the ENTER button is pressed.
[B2121] ANALYZE menu
(STD/COL1/COL2)
Display color temperature and luminance readout
values from the BKM-14L.
X: xxxx: Display the x coordiate of the color system.
Y: xxxx: Display the y coordiate of the color system.
L: xxxx: Display the luminance value.
3 1
Setting the Input Configuration (SET UP 1) —
INPUT CONFIGURATION Menu
Overview
Data pertaining to the input signals are set with the
INPUT CONFIGURATION menu.
When a channel number (1 to 90) is entered with the
numeric keypad, it is then possible to set which input
connector on the rear panel will be assigned to that
channel number, and select the type of signal that will
be connected. The channel numbers from 91 to 99 are
assigned to internal signals.
091: PLUGE signal (Picture Line Up Generating
Equipment)
092: 20% gray signal
093: 100% white signal
094: five-step gray scale signal
095: cross hatch signal
096: cross hatch signal
097: dot signal
098: cross hatch signal
099: 0% black signal
Structure of the INPUT CONFIGURATION Menu
Level 1
Level 2
INPUT CONFIGURATION [C1]
FORMAT [C11]
REMOTE [C2]
SLOT NO
PASSWORD [C3]
INPUT NO
SYSTEM CONFIGURATION [C4]
YC SEP [C12]
ON SCREEN SET [C5]
SYNC MODE
ALIGNMENT [C6]
SCREEN MODE [C13]
EXTEND MENU [C7]
SAFE AREA
SCALE [C14]
APERTURE
VALUE
FILTER
CHANNEL NAME [C15]
COLOR TEMP
H PHASE
SAD H POSITION
COPY [C16]
3 2
Assigning slot and connector numbers
Set which input connector on which slot will be
assigned to the current channel. The slots are
numbered from the left, as seen when facing the rear
panel, with the REMOTE connectors slot being
number 1, the input option slots number 2, and the
analog input connectors slot being number 6. The
connectors are numbered 1 to 6 (from the top) for the
slot.
Assigning the signal type and format
The signal type and format which can be assigned to
each channel number vary, depending on what
adaptors (not supplied) are installed in the rear panel.
[C1]
Level 3
Level 4
COMPOSITE [C111]
NTSC
YC [C112]
PAL
COMPONENT [C113]
PAL-M
SDI [C114]
SECAM
AUTO
4:3 NORM
NTSC
4:3 - UNDR
PAL
16:9- NORM
PAL-M
16:9 UNDR
AUTO
80
90
YUV SMPTE/EBU-N10
100
YUV BETACAM
16:9 - 80
RGB
16:9 - 90
NTSC
16:9 - 100
PAL
4 : 3 - 80
4 : 2 : 2
4 : 3 - 90
AUTO
4 : 3 - 100
PROG
EDIT
CAM
VTR
NEW NAME
OTHER CH
OTHER MONITOR [C161] MONITOR ADDRESS
MEMORY CARD [C162]
FILE NAME
Hide quick links:
Advertisement
Table of Contents
