Sony TRINITRON BVM-14G1A Operation And Maintenance Manual page 15

Location and Function of Parts
Front Panel
BVM-14G5U/14G5E/14G5A
0 SHIFT button
!¡ Function buttons
!™ Monitor Memory
Card slot
!£ OPTION connector
BVM-20G1U/20G1E/20G1A/14G1U/14G1E/14G1A
!£ OPTION connector
1 Tally lamp
2 POWER switch
3 DEGAUSS button
4 Numeric keypad
5 MANUAL adjustment
buttons and knobs
6 Menu operation
buttons
7 POWER lamp
8 STANDBY lamp
9 OVER LOAD lamp
1 Tally lamp
7 POWER lamp
8 STANDBY lamp
9 OVER LOAD lamp
(Illustration: BVM-20G1U/20G1E/20G1A)
9
Location and Function of Parts
This manual explains the location and function of parts
and controls using the control panel of the BVM-
14G5U/14G5E/14G5A. The explanation applies to
BVM-14G1U/14G1E/14G1A/20G1U/20G1E/20G1A
with the BKM-10R/11R Monitor Control Unit.
1 Tally lamp
With factory settings, the Tally lamp lights when pins
No. 8 and No. 9 of the REMOTE 2 connector on the
rear panel are shorted. By changing the setting in the
REMOTE menu, different pins on the remote
connector can be used to control the tally lamp.
For information about the REMOTE menu, see "Assigning
the Remote Control Functions (SET UP 2) —REMOTE
Menu" on page 35.
2 POWER switch
Press to turn on/off the monitor. By setting with the
ADDRESS menu, it is possible to turn on/off the
power of the specified monitors only, or of all
monitors at the same time.
For information about the ADDRESS menu, see "Selecting
the Monitor to Control - ADDRESS Menu" on page 49.
3 DEGAUSS button
Press to degauss the CRT (every time the monitor is
turned on, the CRT is degaussed automatically). To
degauss again, wait for more than five minutes.
4 Numeric keypad
Use to designate the channel number for the input
signal to be monitored, or to enter the setting values
with the menus.
INPUT
1 2 3
4 5 6 Numeric buttons
7 8 9
Ent button: Confirms the
Ent
Del 0
values and characters entered
(ENTER button of the menu
operation buttons 6 has the
same function).
Del button: Deletes the values
and characters entered.
1 0
Channel number entry method:
(In the explanation below, x and y represent any
digit between 1 and 9.)
When selecting a number from 1 to 9, press the x
button to display channel x. When selecting a
number from 10 to 99, press the 0, x, and y buttons
to display channel xy (a two-digit channel number).
5 MANUAL adjustment buttons and knobs
Each press of one of these buttons turns the button's
green LED on or off. When the corresponding button
is on (lit), it is possible to manually adjust the contrast,
brightness, chroma and phase by turning the
corresponding knobs. They are also used to enter the
setting values with the menus. It is possible to set the
preset value for each adjusting item with the
CONTROL PRESET ADJ menu.
For Information about the CONTROL PRESET ADJ menu,
see "Preset Adjustment of the Picture Level Control Knobs -
CONTROL PRESET ADJ menu" on page 25.
Notes
When using the composite SECAM, composite PAL
D, component or SDI (component or composite serial
digital interface) format, note the following.
• The signal phase cannot be adjusted.
• The phase and chroma of RGB signals cannot be
adjusted.
CONTRAST button and
MANUAL
CONTRAST
knob
BRIGHT
BRIGHT button and knob
CHROMA
CHROMA button and knob
PHASE
PHASE button and knob:
Changes the items and
settings on the menus