Sony TRINITRON BVM-14G1A Operation And Maintenance Manual page 16

6 Menu operation buttons
MENU button: Press to display the Menus.
UP MENU
UP/DOWN buttons: Press to select the
DOWN ENTER
items and setting values.
ENTER button: Press to confirm the items
and values entered (Ent button on the
numeric keypad 4 has the same function).
For more information about menu operation, see "Basic
Menu Operations" on page 22.
7 POWER lamp
Lights when the monitor is put into operation mode
from standby mode (see STANDBY lamp 8) by
pressing the POWER switch 2.
Note
When the STANDBY lamp 8 is blinking, the monitor
cannot be put into operation mode (internal data
initialization is taking place). Wait until the
STANDBY lamp 8 is steadily lit.
8 STANDBY lamp
Lights when the monitor is in standby mode. The
monitor will be in standby mode under the following
conditions:
• The MAIN POWER switch (on the rear panel) is
turned on (the STANDBY lamp will blink for a few
moments after the switch is turned on, then will
light).
• The monitor is changed from operation mode to
standby mode by external control.
9 OVER LOAD lamp
Lights to warn of CRT overload.
Location and Function of Parts
0 SHIFT button
Press to select one of the two functions designated to
the function buttons !¡.
Each time the SHIFT button is pressed, the LED turns
on (SHIFT ON: lit in orange) and off (SHIFT OFF: lit
in green).
SHIFT OFF: The functions indicated on the left side
of the function buttons can be used.
SHIFT ON: The functions indicated on the right side
of the function buttons can be used.
SHIFT OFF (LEDs of function buttons in green)
MONO
APT
COMB
ADDRESS
1 1 1 2
!¡ Function buttons
Change the operation conditions for the monitor.
Each time the button is pressed, the LED turns on and
turns off, and the operation conditions are changed.
Each button has two functions. Select one of the two
functions by pressing the SHIFT button 0. When the
SHIFT button is set to ON, the LED lights in orange,
and when the SHIFT button is set to OFF, the LED of
each button lights in green.
(Underscan) button: When this button is pushed in (ON), the picture is
underscanned by 3%, and four ends of the raster is displayed on the screen.
(H delay) button: When this button is pushed in (ON), the picture moves
horizontally, and a horizontal sync signal appears approximately one quarter in the
left edge of the screen.
• The brightness of the picture increases automatically, and it makes it easy to check
the sync part.
• If it is pressed together with the
(V delay) button: When this button is pushed in (ON), the picture moves vertically,
and a vertical sync signal appears approximately in the center of the screen.
• The brightness of the picture increases automatically, and it makes it easy to check
the sync part.
• If it is pressed together with
16 : 9
MONO button: When this button is pushed in (ON), a monochrome picture is displayed.
When the buttons is off, the monitor switches automatically between color and
SYNC monochrome mode, depending on the presence or absence of color burst signal.
BLUE
APT (aperture) button: When this button is pushed in (ON), the frequency response
ONLY
can be modified. The degree of modification is set with the menu.
This function is available when an optional decoder adaptor such as a BKM-24N is
installed.
R
G
B
COMB button: Turn the comb filter on and off.
This function is available when an optional decoder adaptor such as a BKM-24N is
installed.
F1
F3
F1 button: When this button is pushed in (ON), the characters disappear from the
F2
F4
monitor on the MANUAL menu of the level 2 of the CONTROL PRESET ADJ menu, the
MANUAL menu of the level 2 of the COLOR TEMP ADJ menu, and the ALIGNMENT
menu of the level 2 of SETUP menu.
SAFE
AREA
F2 button: When this button is pushed in (ON), you can access directly the MANUAL
menu of the level 2 of the COLOR TEMP ADJ menu, if the short-cut function is assigned
to this button.
ADDRESS button: When this button is pushed in (ON), the ADDRESS menu appears
on the screen. By using the ADDRESS menu, operation conditions for multiple
monitors are set.
For more information about the ADDRESS menu, see "Selecting the Monitor to Control -
ADDRESS Menu" on page 49.
button, a pulse cross picture is displayed.
button, a pulse cross picture is displayed.