Table of Contents
Advertisement
Solution 144
Quick Start Guide
Comms > Remote Access >
RAS Options
1 RAS Allowed
2 Callback Verify
3 Abort RAS On Alarm
4 Answer Bypass
5 Answer Only If Armed
6 Tone Bypass
7 Allow User Functions
8 Report RAS Sessions
Use the [] and [] keys to scroll the list of options. Select
the option required, then press [ON] or [OFF] to enable or
disable. A [] will display to indicate option set. Press [OK]
to save when finished.
Comms > Remote Access >
DTMF Options
1 DTMF Arming
2 DTMF Disarming
3 DTMF User Functions
4 DTMF Quick Arming
5 Reserved
6 Reserved
7 Reserved
8 Reserved
Use the [] and [] keys to scroll the list of options. Select
the option required, then press [ON] or [OFF] to enable or
disable. A [] will display to indicate option set. Press [OK]
to save when finished.
Comms > Remote Access >
Voice Access Code
Reserved for future use.
Comms > Remote Access >
CLI Numbers
1
First
Number
1
Second
Number
1
Third
Number
Use [] and [] keys to scroll cursor left and right. Enter
[0] – [9] for digits and use [] and [] to toggle special
characters - * # and , (pause).
40
MENU 5-3-4
MENU 5-3-5
MENU 5-3-6
9 #
MENU 5-3-7
Digits
Digits
Digits
Up to 3 Phone numbers can be entered for CLI Call
i
Line Identification for remote access detection.
Note
You must enter STD code plus the compete number
for this option to work. Press [OK] after each
Y
telephone number is entered to save and move to
N
the next number.
Y
Y
Comms > Remote Access >
N
User RAS PIN
Y
Y
Use keys [0] - [9] to program User RAS Security PIN + [OK]
Y
to save.
Comms > Reporting >
TX Format Dest 1
00 - Disabled
01 - Contact ID
02 - SIA
03 - Reserved
04 - Reserved
Y
05 - Reserved
N
06 - SMS
N
Use [] and [] keys or enter 0 – 15 then press [OK] to
Y
program the transmission format the control panel will
N
use to report to Destination 1. Only 1 option can be
N
programmed.
N
N
Comms > Reporting >
TX Format Dest 2
00 - Disabled
01 - Contact ID
02 - SIA
03 - Reserved
04 - Reserved
05 - Reserved
06 - SMS
Use [] and [] keys or enter 0 – 15 then press [OK] to
program the transmission format the control panel will
use to report to Destination 2. Only 1 option can be
programmed.
Comms > Reporting
32
Test Route
00 - Log Events Only
32
01 - Dest 1 + Log
02 - Dest 2 + Log
32
03 - Dest 1 & 2 + Log
04 - Dest 2 If 1 Fails
Use [] and [] keys or enter 0 - 4 + [OK]. Enter single
option only. (*** System Wide Parameter ***).
0 0 0 0 0 0 0 0
07 - Domestic
08 - Voice
13 - Ethernet
09 - SIA+
14 - GPRS
10 - GSM SIA+
15 - Reserved
11 - GSM Contact ID
12 - GSM SMS
07 - Domestic
08 - Voice
13 - Ethernet
09 - SIA+
14 - GPRS
10 - GSM SIA+
15 - Reserved
11 - GSM Contact ID
12 - GSM SMS
Bosch Security Systems 10/12 BLCC600R
MENU 5-3-8
MENU 5-4-0
0 1
MENU 5-4-1
0 1
MENU 5-4-2
0 1
Advertisement
Table of Contents
