Preparing For Playback; Speaker Settings - Kenwood VRS-6200 Instruction Manual

Preparing for playback

Speaker settings

To enable you to obtain optimum enjoyment from the receiver's listening
modes, make sure to complete the speaker settings (Subwoofer, Front,
Center, Surround and Surround Back speakers) as described below.
RECEIVER
TUNER, VIDEO, AUX,
GAME/F.AUX
SETUP
SOUND (
MULTI CONTROL %/fi
ON/STANDBY
SOUND (
1
Turn on the power to this receiver by pressing the
ON/STANDBY key (or
2
If you want to use the remote control unit, press the TUNER,
VIDEO, AUX or GAME/F.AUX key on the remote to set it to the
receiver control mode.
3
Initiate the setup mode.
1 Press the SETUP key.
2 Use the MULTI CONTROL button (or the MULTI
CONTROL %/fi keys) for the following displays.
1 "SP SETUP"
2 "TEST TONE"
3 "DISTANCE"
4 "LFE LEVEL"
5 "EXIT"
÷ While the main setup display is appeared, the setup mode
can be canceled by selecting "EXIT" and then pressing the
SETUP key.
The flow of the SETUP is as follows;
SP SETUP TEST TONE
HTB 1 AUTO
HTB 2
HTB 3
L
Custom
C
R
Subwoofer
RS
RB
LB
Front
LS
Center
SW
Surround
Surround
Back
Subwoofer
Re-mix
16 EN
MULTI CONTROL @/#
RECEIVER key).
DISTANCE LFE LEVEL
MANUAL
L Front Left
Center
C
R Front Right
RS
Right Surround
RB
Surround Back Right
LB
Surround Back Left
LS
Left Surround
SW
4
Select a speaker system.
1 Select "SP SETUP" and press the SETUP key again so
that the speaker system indication "SP SYSTEM"
scrolls across the display.
2 Use the MULTI CONTROL button (or the MULTI
CONTROL %/fi keys) to select the speaker system
setting.
1 "HTB 1": Select "HTB 1" if you use speaker system KS-2200HT*.
2 "HTB 2": Select "HTB 2" if you use speaker system KS-3200HT*,
KS-5200HT*, KS-7200HT*.
3 "HTB 3": Select "HTB 3" if you use speaker system KS-8200HT*.
4 "CUSTOM": Select to set up the speakers according to
SETUP
the speaker system in use. (Speaker setup is required
every time after the speaker system is changed.)
* Model availability may differ depending on the country
and sales area.
÷ When the setting "HTB 1", "HTB 2" or "HTB 3" is selected, the
procedure skips to step 5.
÷ When you use a KENWOOD speaker system and select
"HTB 1", "HTB 2" or "HTB 3" set the speaker setup, the audio
will be corrected automatically according to the speaker
characteristics.
÷ When the speaker setting is set to "HTB 1", "HTB 2", "HTB 3 " or
"BS OFF" the DOLBY PRO LOGIC IIx, DTS-ES and DOLBY
DIGITAL EX listen modes cannot be selected.
3 For general speaker setting, use the MULTI CONTROL
button (or the MULTI CONTROL %/fi keys) to select
"CUSTOM", and press the SETUP key again.
÷ The subwoofer setting indication "SUBW" appears.
4 Use the MULTI CONTROL button (or the MULTI
CONTROL %/fi keys) to select the appropriate
subwoofer setting.
EXIT
1 "SUBW ON" :
When a subwoofer is connected.
2 "SUBW OFF" :
When no subwoofer is connected.
÷ The initial setting is "SUBW ON".
÷ When "SUBW OFF" is selected and the selection is
established by pressing the SETUP key in step 5 be-
low, the front speakers are set automatically to "FRNT
LRG" and the procedure jumps to step 8.
5 Press the SETUP key to accept the setting.
÷ The front speakers setting indication "FRNT" appears.
Continued to next page