Normal Playback; Preparing For Playback.14; Remote Operation Of Other Components - Kenwood VR Series Instruction Manual

VR/KRF-V SERIES (En/KM)
Q Jrf/jfsf /A® volume le vels for the speakers.
Sit in your normal listening position and listen to the test tone. Adjust the
volume levels for the speakers unti I al I speakers seem to be equally loud
O
Use the MULTI CONTROL (TUNING/SKIP) to adjust the volume
when the test tone is being output from the speaker channel to
be adjusted.
The channel indication blinks while the test tone is being output.
*fiLch + idS
The test tone Issues from the speakers for 2 seconds at a time
in the following sequence:
Lch — Cch Rch — Sch — Lch
• If you change the volume level settings for the speakers while
listening to music, the settings referred to on this page are also
♦If the speaker setting selects are changed, the speaker level settings
are reset.
O Press the SETUP key.
• The receiver enters the mode for inputting the distance to the
speakers.
Q Input the distance to the speakers.
O
Measure the distance from the listening position to each of the
speakers.
Jot down the distance to each of the speakers.
Distance to front speakers: -feets (meters)
Distance to surround speakers: -feets (meters)
q
Use ,he MULTI CONTROL (TUNING/SKIP) to select the dls-
tance to the front speakers.
The speaker indicator to be adjusted blinks
p I x f j f |
| ^'Tiur
i
luii_I
Indication in feet Indication in meters
• The allowable setting range is f to 30 feet (0.3 to 9.0 m). adjustable
in 1 foot (0.3 m) increments.
G Press the SETUP key.
o Repeat steps G and G to input the distance for the surround
speaker.
G Setup is complete when the input indication reappears.
sp>o)o so® r
sw 1
□ 11
Display when all speakers have been selected.
• The speakers you selected appear on the display. Confirm that all the
speakers have been correctly selected.
* tf you used the remote control (RC-R0608) to perform the settings,
press the VIDEO key at this point to turn off the remote control's own
adjustment mode. In this case, the input source is not switched.
Preparing for playback
Some preparatory steps are needed before starting playback.
VIDEO 2/MONITOR
ON/STANDBY AUTO
i— __JJ
^
T * ^
POWER I INPUT SELECTOR
SPEAKERS A/B (KRF-6020)
SPEAKERS, MUTE (except for KRF-6020)
POWER
INPUT SELECTOR
Turning on the receiver
O
Turn on the power to the related component*.
G Turn on the power to this receiver by pressing POWER (and ON/
STANDBY) key(a).
Selecting TAPE/MD
Select the source name corresponding to the component connected to
the MD/TAPE jacks. The initial factory setting is "TAPE" To change the
source name associated with the MD/TAPE jacks to 'MD, follow the
steps below;
O
Use the INPUT SELECTOR knob to select "TAPE".
G Hold down the AUTO key for more than 2 second*.
• The source indication changes to "MD"
• To return to the original indication, repeat the above procedure.
• You also will need to change the name input to the remote control
(RC-R0608) to "MD". RC-UJ
"selecting the speaker system
Pres* the SPEAKERS A or B key to select the speaker system to be
used.
A ON : Sound from the speakers connected to the SPEAKERS A
term inals on the rear panel.
B ON : Sound from the speakers connected to the SPEAKERS B
terminals on the rear panel.
A+BON : Sound from both the speakers connected to the SPEAKERS
A
and B terminals on the rear panel.
A+BOFF : No sound from the speakers . Use this setting when listening
with headphones for stereo sound in all playback modes.
• Activating a surround mode or selecting "DVD 6ch as the input
source
causes speaker system Ato be selected automatically.
On the VR-305, VR-306, VR-355 and KRF-V5020, press the
SPEAKERS key to switch the speakers on and off.
The indicator for the speakers
you want to use should be lit.
O
Models other than VR-305,
VR-306, VR-355, KRF-V5020
Speaker indicator lights.
VR-305, VR-306, VR-355
and KRF-V5020
Selecting VIDEO 2/MONITOR
Depending on the component connected to the VIDEO 2/MONITOR
jacks, select either the "VIDEO 2" setting or the "MONITOR" setting^