Normal Playback; Preparing For Playback; Listening To A Source Component - Kenwood VR-6070 Instruction Manual

Normal playback
Some
prep~r~r~ry~t~ps(Heneeded
before starting playback.
POWER /ON/STANDBY6
ON/STANDBY 6
(KRF-X9060D)
(VR·6070)
ASPErll~ [sMO~Eo
W
0
~ 'J
15eoEJ
000 -
ell
~l~eEJ~lJ
000
Sao
O~
POWER ON/OFF MDITAPE
(KRF·X90600)
Mi!!i...~"'."i~M~~~ii:f.(I~,,,rt#:~--;_·l,·;':;'
Turning on the receiver
o
Turn on the power to the related components.
Q Turn on the power to this receiver by pressing the POWER ON/
STANDBY <!J (for VR-6070) or POWER ON/OFF and ON/STANDBY
<!J (for KRF·X9060D) key.
~'~:;oj.:\1&.i!i:'J;l,"""l<-~~1<"£Y~t~'JJoI;%;~~':.i~-;';":'<:;'"
Selecting the rnput mode
If you have selected a component connected to the CD/DVD, VIDEO 2,
VIDEO 3 or DVD/6CH jacks, make sure that the input mode setting is
correct for the type of audio signal to be used
-II
Select the source name corresponding to the component connected to
the MDfTAPE jacks. The initial factory setting is "TAPE" To change the
source to "MD", follow the steps below:
Hold down the MD/TAPE key for more than 2 seconds.
• The source indication changes to "MD".
• To return to the original indication, repeat the above procedure.
Jm~1(i.cm.i:M;i~~~-t"'~~"'~~'.~~'f.;.J~~~~.:.J>!:"~l<..~·i",~,;i~',~.:;:~,~,·=-:::,,<;",~;.,- :'';'''«<:;':-'':;::';''~:>;:;';''';':).'':''''''~';;'''';:'':~:'';';'';';~:,.~,;,."""'"
Selecting the speaker system .
Press the A SPEAKERS B key to select the speaker system to be
used.
A ON Sound from the speakers connected to the SPEAKERS A
terminals on the rear panel.
B ON Sound from the speakers connected to the SPEAKERS B
terminals on the rear panel. No sound will be heard from the
subwoofer.
A+B ON : Sound from both the speakers connected to the SPEAKERS
A and B terminals on the rear panel.
A+B OFF : No sound from the speakers. Use this setting when listening
with headphones for stereo sound in all playback modes.
The display segments are different depending on the type of
input signal.
The indicator for the speakers
you want to use should be lit .
• Selecting "6CH INPUT" by pressing the INPUT MODE key, whereby
"DVD/6CH" is the input source will cause SPEAKERS A to be selected
automatically.
Li~teninJl
to aSOU!Ce C01!!pl!llent
VOLUME CONTROL
~ 1--r::=--'~~16
=
F
EJ
1
EJ
1' 0 1
000
8~ 0 Ok
@ BElElEl
000 _
I~~
Input Selector AV AUX
INPUT SELECTOR
o
Use the Input Selector and AV AUX keys to select the
source you want to listen to.
Selecting a source using each key
1
"DVD/6CH"
2
"CD/DVD"
:3
"PHONO"
4 "TUNER"
,5
"VIDEO 1"
6 "VIDEO 2"
7
"VIDEO 3"
8
"MD/TAPE"
:9
"AV AUX"
EJ
Start playback from the selected source.
EJ
Use the VOLUME CONTROL knob or VOLUME
+/-
keys to
adjust the volume.