Panasonic CZ-256ESMC2 Operation Manual page 10

6 Using the System
Air
conditioner
operation
only
5 5
5 5
Note 1
Note 6
Clear accum.data
Main Sub
6 1
6 1
Note 7
Zone name
Main Sub
6 2
6 2
Main Sub ZoneNo./Mng.target
Note 7
(1) Zone No.
(2) Management target
6
6 3
3
Program timer
Main Sub
(1) Daily timer
(2) Weekly timer
6 4
6 4
Ten.Ho/TimerSp.Day
Main Sub
6 5
6 5
Main Sub Prohibit R/C
6 6
6 6
Distribution time zone
Main Sub
6 7
6 7
Main Sub Special distrib. day
6 8
6 8
I/D unit setting
Main Sub
Note 9
(1) Indoor unit capacity
(2) Electric heater capacity
Note 10
6 9
6 9
Other settings
Main Sub
(1) Checking system
con guration
(2) Set/Clear password
(3) No-communications mode
Note 11
(4) Buzzer
Note 12
(5) Initialization
(6) Auto display off
(7) Touch panel calibration
Note 15
(8) Power off
20
5 1
5 1
Main Sub
Displaying Displaying Displaying Displaying
distribution distribution energy energy
ratios ratios usage usage
(simple (loaded (simple (loaded
distribution) distribution) distribution) distribution)
6 Using the System
Air
conditioner
operation
only
6 10
6 10
Note 17
Main Sub WEB settings
6 11
6 11
Note 17
Main User settings
Sub
2
2 5 5
Main Sub Cut-off/Data backup
Note 6
(1) Manual cut-off
Note 13
(2) Data backup
Note 13 and 16
(3) Restore
END
Note 1 Settings are necessary when you would like to monitor operation accumulated time only and
distribution ratio is not needed.
Note 2 Settings are necessary only when air-conditioners include a 3-Way type unit.
Note 3 Make settings even when no distribution is made, if you would like to control units as a bundle of
the group of tenants.
Note 4 Settings are necessary only when the indoor unit has a interface adaptor and is set at almighty.
Note 5 Settings are necessary only for the indoor unit set at almighty.
Note 6 Immediately before delivery, execute "Clear accum.data" to clear total data taken during test runs.
When clearing the test run data after storing it, make "Cut-off" (
Note 7 Make the settings when you would like to operate the unit by optional grouping.
Note 8 When using the unit along with the system controller or ON/OFF-controller, the controller-side
control classi cation needs to be taken into consideration.
The system controller or ON/OFF-controller-side zone varies as varying central addresses from
the Intelligent Controller.
Note 9 Settings are necessary only for interface adaptor.
Note 10 Settings are unnecessary for the simple distribution as they will be taken into consideration in
calculation only for the loaded distribution.
Note 11 Always set the mode at "NO (Normal)".
Note 12 Do not make any initialization imprudently as it may cause missing of all the set and cut-off data.
Note 13 The system works only with the backup PC card inserted, which is separately available.
Note 14 Always manually make the cut-off processing in advance to vary the method of distribution.
Note 15 Although the touch panel is adjusted before factory shipment, calibrate deviations if any.
Note 16 Do not restore any data imprudently as it may return them to their backed-up status.
Note 17 Settings are necessary when you would like to control/monitor the unit via network.
21
5 1
5 1
Main Sub
Displaying Displaying Displaying Displaying
distribution distribution energy energy
ratios ratios usage usage
(simple (loaded (simple (loaded
distribution) distribution) distribution) distribution)
2 5
2 5
Main Sub ) manually.