Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Eldes EPIR
Summary of Contents for Eldes EPIR
- Page 1 GSM ALARM SYSTEM ELDES EPIR...
-
Page 2: Safety Instructions
User Manual v.1.2 Safety instructions Please read and follow these safety guidelines in order to maintain safety of operators and peo- ple around: • Alarm system ELDES EPIR (later referenced as system or detector) has radio transceiver operating in GSM850, GSM900, GSM1800 and GSM1900 bands. • Don’t use the system where it can be interfere with other devices and cause any poten- tial danger. • Don’t use the system with medical devices. • Don’t use the system in hazardous environment. • Don’t expose the system to high humidity, chemical environment or mechanical im- pacts. - Page 3 Fuse F1 type - C1S 2.5A. Blown fuse cannot be replaced by the user and the replace- ment fuses have to be exactly the same as indicated by the manufacturer. If you use I security class computer for setting the parameters it must be connected to earth. WARNING: in order to avoid fire or explosion hazards the system must be used only with approved back-up battery. Special care must be taken when connecting positive and negative battery terminals The WEEE (Waste Electrical and Electronic Equipment) marking on this product (see right) or its documentation indicates that the product must not be disposed of toget- her with household waste. To prevent possible harm to human health and/or the envi- ronment, the product must be disposed on in an approved and environmentally safe recycling process. For further information on how to dispose of this product correctly, contact the system supplier, or the local authority responsible for waste disposal in your area. Copyright © “ELDES UAB”, 2010. All rights reserved It is not allowed to copy and distribute information in this document or pass to a third party without advanced written authorization by “ELDES UAB” “ELSDES UAB” reserves the right to update or modify this document and/or related products without a warning. Hereby, ELDES UAB declares that this GSM Alarm System ELDES EPIR is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. The declaration of conformity may be consulted at www.eldes.lt/ce...
-
Page 4: Package Content
The warranty is voided if the system has been exposed to mechanical impact, chemicals, high humidity, fluids, corrosive and hazardous environment or other force majeure factors. Package content: 1. ELDES EPIR ..................... qty. 1 2. Power Supply ..................qty. 1 3. ELDES EPIR User Manual ..............qty. 1 4. MicroUSB - USB cable ................gty. 1 About User Manual This document describes alarm security system ELDES EPIR installation and operation. It is very important to read User Manual before start using the system. A quick start guide is located in first two chapters. Chapter 3 and 4 describe additional system... -
Page 5: Table Of Contents
3.9 SMS message informing about system arming/disarming ............35 3.10 Setting detector sensitivity level ......................35 3.11. Using Wireless Devices in EPIR868 System ..................36 4. Appendix 4.1 Restoring default parameters ......................37 4.2 ELDES ConfigTool configuration software ..................37 4.3 Replacing back-up battery ........................37 4.4 Technical support ............................. 38 USER MANUAL V.1.2... -
Page 6: General Information
The user listed as Nr.1 gets short SMS message each time the system is successfully armed or dis- armed. When system is armed via phone call, there is 15 second delay before activation, meant for leaving premises. The time delay is user configurable parameter (see chapter 3.3). Red light emitting diode indica- tor (LED) located on detector lense will start to blink informing that time delay has been engaged and user must leave room. The red light goes off upon time-out delay expiration and system is engaged. When detector is disarmed and motion is detected in the room, LED on the lense will be turned on shortly. When detector is armed and upon detection of motion, system will send SMS message until suc- cessful delivery and ring preprogrammed numbers until user picks up or call expires. If user answers the call, remote microphone gets activated for listening. SMS message can be sent to all preprogrammed users (see chapter 3.8 for more details). The system will automatically switch to back–up battery supply in case of mains power failure, and user gets SMS warning message. SMS message will also notify when mains power is restored or back-up battery is about to get discharged and system will be switched off. The user can also inquire the system about system status, power supply status, network quality as well as connect and listen through a remote microphone. The system will ignore requests coming from unknown telephone number or SMS message with wrong password. With correct password user has the capability to access system management from any GSM phone (not necessary pre-programmed). See more details in chapter 3.5. Security system ELDES EPIR868 (ELDES EPIR version with installed 868MHz radio transmitter-receiver) can also operate as an access point for wireless ELDES products: PIR sensors EWP1, sirens, magnetic door/ window sensors EWD1 or expansion modules EW1 and EW2. Using ELDER EPIR868 you can access up to 16 wireless devices at a time. You can find more information about using these devices and chaining them to EPIR868 in the manuals of these products. -
Page 7: Technical Specifications
Maximum motion detection range 10 meters Radio transimtter-receiver frequency* 868 Mhz Radio communication range* up to 30m in premises; up to 150m in open areas Maximum number of wireless devices* 1.4 Main Functions Short description of main functions: ELDES EPIR holder used for wall fixing Detector lense with LED indicator light Power supply socket Power supply Power supply connector Button to restore default parameters Microphone Holder fixing place Backup Battery 10. Micro-USB connector 11. SIM card holder... -
Page 8: System Installation
1.5 System installation The system should be installed indoors. Choose location where unauthorized entry is most likely. To avoid fault alarms, avoid installing in following locations: • locating lens towards direct sunshine, e.g. facing windows • near devices with high temperature fluctuations, e.g. fireplace or heating boiler • places with increased dust or air flow traffic • metal or shielded wall where GSM connection might be lost Place SIM card in the mobile phone and make sure that SIM card PIN code is disabled by follow- ing appropriate menus. SIM card should not have any remaining SMS messages. RECOMMENDATION It is worth to choose the same GSM cellular provider as most users use assuring fast and reli- able SMS message delivery and phone call connection. RECOMMENDATION To increase system reliability, it is recommended not to use prepaid SIM cards. The system would fail to send any messages upon depletion of prepaid account. - Page 9 1. Fix the holder to 2. Insert SIM card the wall with PIN code disabled 3. Plug power 4. Place ELDES supply EPIR into the connector holder 5. Plug power supply into mains socket 6. The system starts in 1-2 minutes. When LED is off, move your hand in front of ELDES EPIR lense and watch the system detecting motion and turning on LED for few seconds. If LED indicator is blinking fast (few times a second), could be that SIM card in not inserted properly or PIN code has not been disabled. * Remove upper half of the device (with detector lense) by turning off the screw. SIM card should be respectively inserted to the corresponding holder (see 1.4 chapter). USER MANUAL V.1.2...
-
Page 10: System Pre-Operation And Essential Control Commands
2. System pre-operation and essential control commands VERY IMPORTANT!!! Underscore symbol ‘_’ in this manual is used to represent space. When writing SMS messages, every underscore symbol should be replaced by single space symbol. XXXX – means password. Don’t leave any space at the beginning and the end of the message. To set ELDES EPIR system parameters easier and quicker you can use the computer, USB cable and configuration program ELDES EPIR ConfigTool. You can read more in chapter 4.2. 2.1 Selecting device language and verification of SMS central number The language in which the device communicates with the user can be chosen before changing factory default password. To change the language in the system that is already configured reset default set- tings as described in 4.1 appendix. Send SMS message with the required language code to the number of the SIM card inserted in ELDES EPIR. E.g., if you want to set the English language send the following SMS message: EN... -
Page 11: Password Change
All SMS commands start with a password, so please memorize it well. Manufacturer default password is four zeros 0000, which 0001 PSW is necessary to change. Manufacturer default password can be 1111 changed by sending SMS message to ELDES EPIR: 0000_PSW_XXXX To replace your password, send SMS message: YYYY_PSW_XXXX XXXX – any four digit number except four zeros. Non-numerical characters like dots, colons, spaces are not allowed. YYYY – old system password. -
Page 12: Saving Or Changing Numbers
2.3.1 Saving or Changing numbers Send SMS message with text to ELDES EPIR: XXXX_NR1:37011111111_NR2:37011111111_NR3:37011111111_ NR4:37011111111_NR5:37011111111 Ones should be replaced with user numbers. Numbers don’t have to be entered all or in sequential order right away. E.g. use can en- ter first and fourth number by sending following SMS message: 0001 NR1: 37011111 XXXX_NR1:37011111111_NR4:37011111111 Or individually one number at a time: XXXX_NR3:37011111111 Numbers can be changed same way as described above. New number will overwrite old one, therefore no erasing is necessary. 2.3.2 Verification of saved numbers... -
Page 13: Date And Time Settings
2.4 Date and time settings It is important to set correct date and time, so that the system can send reports at specified times. Date and time can be set by sending following format SMS message: XXXX_MMMM.mn.dd_hh:mi Where MMMM – means year, mn – month, dd – day, hh – hour, 0001 2009.01. mi – minutes 01 14:15 E.g. 0000_2009.01.01_14:15 USER MANUAL V.1.2... -
Page 14: Additional System Capabilities
Zone names can have up to 14 characters. 3.2 System and Zone status To find out current zone names, settings and status, send SMS message XXXX_STATUS The system will reply, e.g. System is armed/disarmed Z1:MOTION:ON/OFF ON- means enabled. OFF- disabled ATTENTION: In the system of ELDES EPIR868 you can receive information about up to 32 ad- ditional zones inputs and/or up to 32 additional controlled outputs (it depends on how many wireless devices is added to the security system). In this case system will send a reply by SMS messages, in each of them placing information about 4 active zones inputs or/and controlled outputs (it wont send information about inactive zones and controlled outputs). For example, if there is added 1 expansion module EW1 (with 2 inputs and 2 outputs) to the system, admin- istrator will receive 2 SMS messages about 3 zones and 2 controlled outputs. 3.3 Exit time-out configuration When system is armed, the user should leave premises within specified time (manufacturer default 15 seconds). During this period detector ignores motion. Running time-out is indicated by blinking... -
Page 15: Info On Status Sms
3.4 Info on status SMS Security system EPIR can be inquired at any time about its status, signal strength, zone status. At the same time system can be tested. If SMS response message is received, means system is functioning properly. -
Page 16: Blocking Unknown Incoming Numbers
3.5 Blocking unknown incoming numbers By default ELDES EPIR can be controlled from any of the pre-programmed numbers NR1 .. NR5. But user can access the system and control parameters from any number as long as password is know. To enable this feature, send SMS message: 0001 STR: XXXX_STR:ON To disable this feature, send SMS message: XXXX_STR:OFF 3.6 External power supply control The system ELDES EPIR will report every time mains 230V power supply fails or recovers. In some remote places where mains power supply is unreliable, the system can be configured to ignore these changes. Send SMS: XXXX_M:OFF 0001 M: Or it can be enabled by SMS message: XXXX_M:ON 3.7 Remote Microphone listening To be able to listen what is going on in remote house can be done in two different ways: 1. When alarm has been activated, the system will ring pre-programmed numbers and user... -
Page 17: Sms Message Delivery To Multiple Users
3.8 SMS message delivery to multiple users Upon activated alarm, SMS messages are repeatedly sent until first successful delivery to one of the users. System starts with NR1, and if delivery fails, follows with NR2, etc. It is also possible that SMS message will be sent to all recorded users. To enable this function, send SMS message: XXXX_SMSALL:ON To disable this function, send SMS message: XXXX_SMSALL:OFF 3.9 SMS message informing about system arming/disarming By default the user NR1 will receive a short message every time system is armed or disarmed. To disable this function, send SMS message: XXXX_MASTER:OFF To re-enable this function, send SMS message XXXX_MASTER:ON 3.10 Setting detector sensitivity level The manufacturer has set optimal detector sensitivity level. However, in some cases the system is installed in windy premises where the air flow can cause false alarms. In such cases sensitivity level can be reduced. In order to increase or reduce motion detector sensitivity the user has to send the following text message to the system ELDES EPIR: 0001 LEVEL:XX XXXX_LEVEL:XX where XX is a two-digit number that can be [20-99]. Factory default value is 40. The greater the number value, the lower detector sensitiv- ity level. In order to find out the set sensitivity level the user should send the following SMS message: XXXX_LEVEL USER MANUAL V.1.2... -
Page 18: Using Wireless Devices In Epir868 System
3.11. Using Wireless Devices in EPIR868 System ATTENTION: binding of wireless devices is supported only by ELDES EPIR868. Security system ELDES EPIR868 can be expanded by connecting additional wireless ELDES devices: • PIR sensors EWP1 (motion detectors). It allows to expand secured territory up to 16 additional security zones; • expansion modules EW1 with 2 inputs and 2 programmable outputs. It is used for attaching more devices (various detectors, sirens) to the security system. • expansion modules EW2 with 4 inputs and 6 programmable outputs. It is used for attaching more devices (various detectors, sirens) to the security system. • wireless sirens; • wireless magnetic door/window sensors EWD1; It is possible to connect up to 16 wireless devices to the central security system at a time. Maximum distance for wireless connection is 150 meters (in open areas). For more information please check user manuals of these devices. - Page 19 USER MANUAL V.1.2...
-
Page 20: Appendix
To change back-up battery, follow these steps: 1. Unplug power supply form mains power 2. Remove ELDES EPIR from holder 3. Unplug power supply connector 4. Remove screw located on the back side of ELDES EPIR 5. Open ELDES EPIR enclosure 6. Carefully remove back-up battery 7. With one hand holding back-up battery, unplug battery connector 8. Replace battery. Use battery type as specified in technical specifications. 9. Repeat all steps in inverse order... -
Page 21: Technical Support
· Incorrect SIM central number · No network signal · User number is not programmed in (or disabled access from unknown numbers) Received SMS message · Wrong syntax “Incorrect Format” · Could be space left in wrong SMS message place · Manufacturer default password not changed · Missing user NR1 If your problem could not be fixed by the guide above, please contact your distributor or manufac- turer tech support by email support@eldes.lt More up to date information about your device and other products can be found at manufacturer’s website www.eldes.lt USER MANUAL V.1.2...
Need help?
Do you have a question about the EPIR and is the answer not in the manual?
Questions and answers
Здравствуйте! После перезагрузки сигнализации не могу установить 4х значный пароль. Просит ещё пароль админа, а я не знаю где найти
To reset the admin password for the Eldes EPIR alarm system and set a new 4-digit code, send an SMS message in the following format:
1. If using the factory default password (0000):
0000_PSW_XXXX
(Replace "XXXX" with your new 4-digit password.)
2. If changing an existing password:
YYYY_PSW_XXXX
(Replace "YYYY" with the current password and "XXXX" with the new 4-digit password.)
Notes:
- The password must be a 4-digit number, excluding "0000".
- Do not use spaces, colons, or dots.
- If the password is forgotten, reset the system to factory settings.
This answer is automatically generated