Taiden HCS-5300 Installation And Operating Manual
  1. Manuals
  2. Brands
  3. Taiden Manuals
  4. Conference System
  5. HCS-5300
  6. Installation and operating manual

Taiden HCS-5300 Installation And Operating Manual

Digital infra-red wireless conference system
Hide thumbs Also See for HCS-5300:
Table of Contents

Advertisement

Quick Links

HCS-5300 Digital Infra-red Wireless Conference System
Excellent solutions for conferences
Installation and Operating Manual
V 1.3

Advertisement

Table of Contents
loading

Related Manuals for Taiden HCS-5300

Summary of Contents for Taiden HCS-5300

  • Page 1 HCS-5300 Digital Infra-red Wireless Conference System Excellent solutions for conferences Installation and Operating Manual V 1.3...
  • Page 2 To protect your hearing avoid high pressure level on earphones. Adjust to a lower and convenient level. If any detailed information needed, please contact your local agent or TAIDEN service center in your region. Any feedback, advice and suggestion about the products is appreciated...

  • Page 3: Important Safety Instructions

    Important Safety Instructions Read these instructions. 18. All TAIDEN products are guaranteed for 3 years Keep these instructions. excluding the following cases: A. All damage or malfunction caused by human Heed all warnings. Follow all instructions. negligence; B. Damage or malfunction caused by improper Do not use this apparatus near water.
  • Page 4 Important Safety Instructions Attention: Installation should be performed by qualified service personnel only in accordance with the National Electrical or applicable local codes. Power Disconnect: Units with or without ON – OFF switch have power supplied to the unit whenever the power cord is inserted into the power source;...
  • Page 5 Lithium battery safety precautions To change battery please power off and take off the battery immediately. Keep the battery away from heat sources to prevent fire or explosion. Do not use a battery that is leaking, deformed, discolored or overheats. Take extra precautions to keep a leaking battery from fire.

  • Page 6: Table Of Contents

    Contents Installation & User Guide......................VIII Chapter 1 System introduction ....................1 1.1 Overview ................................1 1.2 Functions and features............................4 1.3 System technology ..............................5 1.3.1 Basic system concept..............................5 1.3.2 IR radiation ..................................5 1.3.3 Carriers and channels ..............................5 1.4 Aspects of infrared signal transmission.......................6 1.4.1 Ambient lighting................................6 1.4.2 Objects, surfaces and reflections ..........................6 1.4.3 Infrared service area of digital infrared wireless conference unit.................7...
  • Page 7 2.6.18 About ..................................29 2.6.19 Volume Control................................30 2.6.20 Connecting to PC ..............................30 Chapter 3 Digital infrared transceiver and receiver ..............31 3.1 Overview ................................31 3.2 Functions and indications..........................32 3.2.1 Digital infrared transceiver............................32 3.2.2 Digital infrared receiver .............................33 3.3 Infrared service area ............................34 3.4 Position planning ...............................36 3.4.1 Precautions in planning the digital infrared transceiver/receiver................36 3.4.2 Planning digital infrared transceiver ..........................38...
  • Page 8 6.1 Digital infrared wireless conference unit ........................68 6.2 Digital infrared wireless main unit ..........................69 6.3 Charging Unit................................69 Chapter 7 Technical data......................70 7.1 System specification ..............................70 7.2 Digital infrared wireless main unit ..........................71 7.3 Digital infrared transceiver ............................72 7.3.1 Digital infrared transceiver............................72 7.3.2 Digital infrared receiver .............................73 7.4 Digital infrared wireless conference unit ........................74 7.4.1 Digital infrared wireless conference unit........................74...

  • Page 9: Installation & User Guide

    The manual is divided into the following chapters: Chapter 1: Introduction Introduction to the HCS-5300 system, as well as introducing the user into structure, technical principle, and aspects of system planning. Chapter 2: Digital infrared wireless conference...
  • Page 10 HCS-5300RB Digital Infrared Receiver (ceiling, wall or tripod- Distributor mounted, excl. tripod when ordered) HCS-5352 Cable Splitter (1 input & 4 outputs, for HCS-5300 series Digital IR Wireless Conference Unit transceiver) HCS-5300C HCS-5352R Digital IR Wireless Chairman Unit (5 voting keys, 1+3 Cable Splitter (1 input &...
  • Page 11 Installation & User Guide Lithium Rechargeable Battery Pack HCS-5300BAT Lithium Rechargeable Battery Pack (for HCS-5300 series conference unit) HCS-5300HT-BAT Lithium Rechargeable Battery Pack (for HCS-5300HT portable digital IR transmitter) Charging Device HCS-5300CHG/08 Charging Unit (8 pcs/case) HCS-5300HT/CHG Digital IR Receiver Charging Base...

  • Page 12: Chapter 1 System Introduction

    Chapter 1 System introduction 1.1 Overview TAIDEN HCS-5300 series product is a digital infrared The system consists of one digital infrared wireless wireless conference system convenient for mobile use conference main unit, one or more digital infrared as well as for permanent installations. The flexibility of...
  • Page 13 Digital Infrared Receiver (suspension) Distributor HCS-5300RB HCS-5352 Digital Infrared Receiver (ceiling, wall or tripod- Cable Splitter (1 input & 4 outputs, for HCS-5300 series mounted, excl. tripod when ordered) transceiver) HCS-5352R Digital IR Wireless Conference unit Cable Splitter (1 input & 4 outputs, for HCS-5300 series...
  • Page 14 HCS-5300HT-BAT Lithium Rechargeable Battery Pack (for HCS-5300HT portable digital IR transmitter) Charging Device HCS-5300CHG/08 Charging Unit (8 pcs/case) HCS-5300HT/CHG Digital IR Receiver Charging Base Power Adapter HCS-ADP15V Power Adapter (DC 15 V, 2.2 A) Dedicated Cable CBL5300-05 5 m Dedicated Transceiver Cable CBL5300-10 10 m Dedicated Transceiver Cable CBL5300-20...

  • Page 15: Functions And Features

    1.2 Functions and features 1. Digital infrared wireless conference system 5. Full functions operating TAIDEN dirATC technology - digital Discussion infrared Audio Transmission Control Vote (5 keys) technology Simultaneous interpretation (1+3 channels) Isolated audio recording function simultaneous interpretation (1+3 channels) 2.

  • Page 16: System Technology

    1.3.1 Basic system concept 1.3.2 IR radiation The system composition of HCS-5300 digital infrared Audio and control signals of HCS-5300 are transmitted wireless conference system is shown in figure 1.2. It is as modulated infrared light. Infrared radiation is part of...

  • Page 17: Aspects Of Infrared Signal Transmission

    This can be solved by using a sufficient quantity of transceivers. They should HCS-5300 system adopts 2-8 MHz wave band, and be positioned in a manner to provide an infrared field has very good anti-interference performance (see strong enough to cover the whole conference area.

  • Page 18: Infrared Service Area Of Digital Infrared Wireless Conference Unit

    In the vertical direction, the user can select "Vertical", wireless conference unit gets best sensitivity when it "Horizontal" or "V+H" work area according to directly faces a transceiver. Every HCS-5300 series transceiver installation location, to ensure the most digital infrared wireless conference unit is equipped effective sending and receiving infrared signals.

  • Page 19: Infrared Service Area Of Digital Infrared Transceiver

    1.4.4 Infrared service area of digital infrared transceiver receiving plane determined by the position of the infrared wireless conference unit. The type of the digital infrared transceiver determines If infrared signals between the transceiver(s) and the the covering area. More transceivers can enlarge the conference unit can get directly to each other, their covered area.

  • Page 20: Overlap And Multipath Effects

    e. Coverage area of digital infrared transceiver HCS-5300TDB Figure 1.7 Coverage area of digital infrared transceiver 1.4.5 Overlap and multipath effects If footprints of two transceivers overlap, its total However, due to the differences in the delays of the coverage area may be larger than the sum of the two signals from two or more transceivers, the signals may separate footprints.

  • Page 21: Chapter 2 Digital Ir Wireless Conference System Main Unit

    Chapter 2 Digital IR Wireless Conference System Main Unit 2.1 Overview HCS-5300M/20 digital infrared wireless conference system main unit is the heart of the HCS-5300 wireless conference system. The main unit can be connected to digital infrared transceivers and recording devices and:...

  • Page 22: Functions And Indications

    2.2 Functions and indications Front panel of HCS-5300M/20 main unit Rear panel of HCS-5300MA/MB/20 main unit Rear panel of HCS-5300MC/20 main unit Figure 2.1 Digital infrared wireless conference system main unit...
  • Page 23 Front panel: Backside: 1. “STANDBY” button 14. “LINE IN 1”（6.4 mm jack） 2. “MENU” button 15. Ethernet The LCD displays the initial user interface: press Communication with PC under TCP/IP protocol; this button to enter the LCD set-up menu; or remote controlling through Ethernet interface; The LCD displays the set-up user interface: press or access to WLAN and fulfill remote controlling this button to select the highlighted item or enter...

  • Page 24: Installation

    2.3 Installation HCS-5300M/20 series digital infrared wireless conference system main unit can be fixed in a standard 19-inch cabinet. The main unit is equipped with a pair of fixing brackets ①. First unscrew the lateral screws ② from the housing. Then fasten the brackets with these screws and put the main unit in the cabinet.

  • Page 25: Connection

    “Analog”. 2.4.1.1 To HCS-4385K2/50 through Interpreter’s unit interface HCS-5300MA/MB/20 main unit has embedded 1+3 channels simultaneous interpretation. TAIDEN HCS-4385K2/50 interpreter units can be connected directly to HCS-5300MA/MB/20 from interpreter’s unit interface and fulfill four channels simultaneous interpretation (including floor audio).

  • Page 26: To Other Auxiliary Devices

    2.4.2 To other auxiliary devices 2.4.2.1 To external audio device 2.4.2.3 To PA Digital infrared wireless conference main unit can be HCS-5300M/20 series digital infrared wireless connected to an external audio device through LINE IN conference system main unit has a balanced floor interface.

  • Page 27: System Connection

    2.4.3 System connection [Wireless discussion + 1+3 CHs digital simultaneous interpretation + voting + video tracking HCS-5300MA/20 has the functions for discussion, vote high-speed dome camera. and 1+3 CHs digital simultaneous interpretation. The Use a RS-485 cable and connect the HCS-5300M/20 system can be connected to an automatic video main unit (port “TO VIDEO SWITCHER”) to the tracking system.

  • Page 28: System Connection [Wireless Discussion + 1+3 Chs Digital Simultaneous Interpretation + Video Tracking + Central Control]

    Switch on/off microphone of conferen ce unit; switcher (port “TAINET”). 4 CHs digital infrared language distribut system; lso, TAIDEN HCS-5300 digital infrared wireless Video tra cking, and cameras can be remote conference system and TAIDEN HCS-6100 intelligent controlled; central control system can be joined together...
  • Page 29 Figure 2.10 System connection [Wireless discussion + 1+3 CHs digital simultaneous interpretation + video tracking + central control]...

  • Page 30: System Connection [Wireless Discussion + Video Tracking + Central Control]

    Multiform functions can be realized with the following port at the rear panel of the video switcher (port system configuration: “TAINET”). Digital infrared wireless conference; Switch on/off microphone of conference unit; TAIDEN HCS-5300 digital infrared wireless Video tracking, and cameras can be remote Also, conference system and...
  • Page 31 Figure 2.11 System connection [Wireless discussion + video tracking + central control]...

  • Page 32: Menu Structure

    2.5 Menu structure Figure 2.12 Digital infrared wireless conference system main unit menu structure...

  • Page 33: Configuration And Operation

    2.6 Configuration and operation Digital infrared wireless conference system main unit can C) Access main menu be configured and set up through menu operation with Pressing the “Menu” button under initial interface will go four buttons. All menu items operation will be introduced to main menu, which includes eighteen menu items: one by one in this section.

  • Page 34: System Status

    2.6.1 System Status “System Status” submenu includes: d) SI Status “Carrier Using Status” Use the “ / ” button to select “SI Status” and use the “Microphone Battery Status” “MENU” button to confirm. “Carrier Using Sequence” The status of the simultaneous interpretation channels “SI Status”...
  • Page 35 b1) Set up interpretation language b2) Set up interpretation language 1). Set up channel 1 first, use the “ / ” button to switch 1). Set up channel 1 first, use the “ / ” button to switch between languages; between languages;...
  • Page 36 e2) Select language for booth “None” stands for no language output from To distribute the interpretation languages separately, channel B; A/B/C channels are provided in each interpreter unit. The “All” stands for the language of channel B which language setting of A/B/C channels for all interpreter units can be any of the selected languages.

  • Page 37: Line In 2 Setting

    b). Press the “MENU” to save and return to upper level menu. 2.6.3 Line in 2 Setting a). Press the “ / ” button to select “Monitor Ch.” or Adjust LINE IN 2 volume, range: mute, -30 dB - 0 dB. “Monitor Vol.”;...

  • Page 38: Ring Setting

    2.6.8 Ring Setting “Set All Mics” Select ring tone on/off on request to speak, when chairman priority button is pressed or when timing speech. a). Press the “ / ” button to adjust the gain of all a). Press the “ / ” button to select ring on/off; microphones, range: -12 dB - 12 dB;...

  • Page 39: Microphone Auto Off Setting

    2.6.11 Microphone Auto Off Setting 2.6.14 Network Setting “Network Setting” includes three submenus: “IP address” “Subnet mask” “Gateway” Use the “ / ”.button to select to turn off or not turn off the microphone automatically after a period of silence. “Yes”: the microphone will automatically switch off after a period of silence and the period shall be set up a) Setting up unique “IP Address”...

  • Page 40: Time Setting

    2.6.15 Time Setting Set system clock. b). When the first time column scan is finished, press any button to start the first time line scan; a) Press the “MENU” button to go to “Year”, “Month”, “Day”, “Hour”, “Minute” in turn; b) Press the “...

  • Page 41: Volume Control

    2.6.19 Volume Control The volume can be adjusted by the volume knob on the CMU front panel - LINE IN 1 VOL. adjust knob and MASTER VOLUME adjust knob. Meanwhile, corresponding volume indicator will be displayed on the LCD, as shown in the following figure: 2.6.20 Connecting to PC When connecting the CMU to the PC, its front panel will be locked and setup operation cannot be accessed, as...

  • Page 42: Chapter 3 Digital Infrared Transceiver And Receiver

    Chapter 3 Digital infrared transceiver and receiver 3.1 Overview digital infrared transceiver manages communication between main unit conference units. The digital infrared receiver receives the infrared signals from the digital infrared transmitter, and sends the signals to the main unit. It can be mounted onto the ceiling or the wall for optional coverage or fixed onto a tripod at any appropriate spot.

  • Page 43: Functions And Indications

    3.2 Functions and indications 3.2.1 Digital infrared transceiver Note: HCS-5300TDS-W/N digital infrared transceiver has four built-in switchers to select the radiation area, they were switched to “ON” in the factory. If necessary in the practical application, please remove the top cover and switch off one or more radiated areas by selecting the corresponding switcher(s).

  • Page 44: Digital Infrared Receiver

    3.2.2 Digital infrared receiver Figure 3.4 HCS-5352R cable splitter for receiver HCS-5300RA digital infrared receiver Figure 3.4: 1. To the transceiver interface of the main unit 2. Four receiver interfaces HCS-5300RB digital infrared receiver Figure 3.3 HCS-5300R digital infrared receiver Figure 3.3: Cable CBL-5304 (10 meters) Power indicating light...

  • Page 45: Infrared Service Area

    3.3 Infrared service area a. Coverage area of HCS-5300TD-W digital infrared transceiver signal b. Coverage area of HCS-5300TDS-W digital infrared transceiver signal c. Coverage area of HCS-5300TD-N digital infrared transceiver Mounting Coverage Type d. Coverage area of HCS-5300TDS-N height H area radius R digital infrared transceiver signal 2.5 m...
  • Page 46 a. Coverage area of HCS-5300RA digital infrared receiver signal b. Coverage area of HCS-5300RB digital infrared receiver signal Type Mounting height H Coverage area radius R 2.5 m Approx. 13 m 3.0 m HCS-5300RA 3.5 m HCS-5300RB Approx. 11 m 4.0 m 4.5 m Figure 3.6 Coverage area of HCS-5300R digital infrared receiver signal...

  • Page 47: Position Planning

    Especially reflections caused by pillars in large 3.4.1.2 Stay away from lighting equipment halls may cause disturbance. Although HCS-5300 system has good anti-interference performance to ambient light, the distance of the transceiver/receiver from lighting equipment must be at 3.4.1.4 Make each conference unit communicating...
  • Page 48 Figure 3.10 Infrared signals blocking So, each transmitter should communicate with more than one receiver to avoid blocking. 3.4.1.5 Stay away from plasma displays When planning an infrared wireless discussion system, plasma displays are not appropriate to be used in the venue.

  • Page 49: Planning Digital Infrared Transceiver

    3.4.2 Planning digital infrared transceiver The coverage area of the digital infrared transceiver is defined by the distance between the transceiver and the conference unit. Select suitable transceiver type according to the height of the conference room, locate them at reasonable positions and place all conference units within the coverage area.
  • Page 50 3.4.2.2 Example for planning the transceiver 【Square table arrangement】 【Rectangular table arrangement】 If the transceivers are arranged as shown in the following Generally: conference rooms with identical figure, the coverage area of infrared signals will cover dimensions, position transceivers the entire meeting room. determined by the arrangement of the conference units (Figure 3.17 and 3.19) The following figures show the ideal position planning of...
  • Page 51 A) Conference style seating (circulatory seating) B) Parliamentary seating Within the circulatory seating operating area of the If the transceivers for parliamentary seating would be conference units, the transceivers must be placed evenly. placed evenly as shown in Figure 3.17, transceiver No. 1 Make sure that all conference units communicate with at could only communicate with the few conference units in least two transceivers.

  • Page 52: Planning The Path From Main Unit To Transceiver

    3.4.3 Planning the path from main unit to transceiver 3.4.3.1 Cautions for cable connecting 3.4.3.2 Using distributor The distances between main unit and every If using distributors, do not use more than one distributor transceiver must be equal in one branch, or it will increase high frequency signal loss and may cause system fault.
  • Page 53 Note: The same rule is also applicable for two systems installed in one room but have enough distance that they will not interference to each other.

  • Page 54: Installation

    3.5 Installation 3.5.1 Installation of HCS-5300TD 3.5.1.1 Ceiling mounted ① HCS-5300TD digital infrared transceiver ② HCS-5300TD digital infrared transceiver ceiling-mounting kit ③ Mounting hole (drilled on the ceiling) ④ Ceiling Figure 3.24 HCS-5300TD digital infrared transceiver ceiling mounted Mounting steps: Step 1: Install the ceiling mounting kit at the top of the HCS-5300TD Transceiver;...
  • Page 55 3.5.1.2 Ceiling mounted ① M3 screw ② Hard ceiling mounting bracket ③ Rubber plug ④ Hard ceiling (such as cement ceiling) ⑤ HCS-5300TD digital infrared transceiver Figure 3.25 HCS-5300TD digital infrared transceiver ceiling mounted Mounting steps: Step 1: Position the mounting bracket on the ceiling according to the installation location of the HCS-5300TD and mark the positions of the drilling holes.
  • Page 56 3.5.1.3 Tripod mounted (Adjustable angle) ① HCS-5300TD digital infrared transceiver ② M3 screw ③ Wall-mounted bracket (with flexible tube) ④ Tripod-mounted stator ⑤ HCS-5300TZJ tripod (should be ordered separately) Figure 3.26 HCS-5300TD digital infrared transceiver tripod mounted Mounting steps: Step 1: Fix the HCS-5300TD digital infrared transceiver onto the wall-mounted bracket with M3 screws;...
  • Page 57 3.5.1.4 Wall mounted (Adjustable angle) ① HCS-5300TD digital infrared transceiver ② M3 screw ③ Wall-mounted bracket (with flexible tube) ④ Wall Figure 3.27 HCS-5300TD digital infrared transceiver wall mounted Mounting steps: Step 1: Fix the HCS-5300TD digital infrared transceiver onto the wall-mounted bracket with M3 screws;...

  • Page 58: Installation Of Hcs-5300Tdb

    3.5.2 Installation of HCS-5300TDB ① Hard ceiling mounting bracket ② HCS-5300TD digital infrared transceiver ③ HCS-5300TZJ tripod (should be ordered separately) Figure 3.28 HCS-5300TD digital infrared transceiver tripod mounted Mounting steps: Step 1: Put the bracket on the bottom of the transceiver and fix it with rotation; Step 2: Aim the mounting hole at the bottom of HCS-5300TD digital infrared transceiver to M10 screw on the tripod;...

  • Page 59: Installation Of Hcs-5300Tds

    3.5.3 Installation of HCS-5300TDS ① M6×60 hook up riveting bolt ② M4 screw（M4×40）and nut ③ User customized suspension (see figure 3.30 for requirements) or HCS-5300TDP suspension (optional length) ④ M3×12 screw ⑤ Hard ceiling (such as cement ceiling) Figure 3.29 HCS-5300TDS digital infrared transceiver suspension mounted Mounting steps: Step 1: Fix M6×60 hook up riveting bolt onto the hard ceiling (such as cement ceiling);...
  • Page 60 Figure 3.30 Requirements of user customized suspension...

  • Page 61: Connecting To Main Unit

    3.6 Connecting to main unit Connect the transceiver to the main unit with designated 6-pin 100 Mbps high speed cable (see figure 3.31). Note: The correctness of the cable connection can be ascertained if the indicating light on the transceiver is lighting up. If the indicating light is not switched on, cable connection failure or short circuit should be considered.

  • Page 62: Chapter 4 Digital Infrared Wireless Conference Unit

    Chapter 4 Digital infrared wireless conference unit 4.1 Overview HCS-5300 series digital infrared wireless conference units are the basic devices for the participators, divided into delegate unit and chairman unit with priority features. Different functions are available, depending on the conference unit type used.

  • Page 63: Functions And Indicating

    4.2 Functions and indicating 4.2.1 Digital IR Wireless Conference Unit HCS-5300CE HCS-5300DE HCS-5302C HCS-5302D HCS-5301D Bottom side Left side Right side Figure 4.1 HCS-5300 series digital infrared wireless conference unit...
  • Page 64 Figure 4.1: button to vote for candidate 1; 1. Infrared transmitting/receiving glass – at the In audience response/rating state of voting frontage of the conference unit for transmitting/ mode, voting indicating light will blink, press this receiving infrared signals. button to give a response “0” of “100” (“- -”). Yes/ Candidate 2/Response- (“YES/2/-”): Note: In parliamentary state of voting mode, voting...
  • Page 65 can press this key to enter the voting status. Once the chairman voted, the indicating light will blink again. After confirmation that all delegates voted, the chairman pushes key “5” to close voting. Application software will calculate the voting results. 10.

  • Page 66: Portable Digital Ir Transmitter (Hcs-5300Hs Needed)

    4.2.2 Portable Digital IR Transmitter (HCS-5300HS needed) Figure 4.2 HCS-5300HT Portable Digital IR Transmitter Figure 4.2: 1. Power switch 6. Channels capacity 2. Channel selector 7. Charge contact 3. HCS-5300HS interface 8. Portable buckle 4. Power indicating light 9. Battery cover 5.

  • Page 67: Infrared Service Area

    In the vertical direction, the user can select "Vertical", wireless conference unit gets best sensitivity when it "Horizontal" or "V+H" work area according to the directly faces a transceiver. Every HCS-5300 series transceiver installation location, to ensure the most digital infrared wireless conference unit is equipped effective infrared signal reception and transmission.
  • Page 68 HCS-5300HS Microphone HCS-5300HT Figure 4.4 Coverage area of the Digital IR Transmitter...

  • Page 69: Precautions In Using

    4.4 Precautions in using Avoid direct sunshine when using, otherwise it The distance between the conference unit and may cause signal blocking the nearest transceiver must be at least 2 meters or more. Figure 4.5 Close curtain to avoid direct sunshine The distance between adjacent conference units Figure 4.7 Distance between conference unit and must be at least 0.5 meter;...

  • Page 70: Operation

    For “Last key-press valid” voting, the delegate can change his/her vote. When the delegate voted, the Figure 4.8 HCS-5300 series digital infrared wireless indicating light of his voted key will be activated and conference unit with microphone all other indicating lights will be deactivated.

  • Page 71: The Operation Of Chairman Unit

    When the earphone is pulled out, the conference unit (application software needed) will switch to floor audio channel automatically. When the application software displays the voting result, voting result will also be displayed on the Select working angle LCD: In the vertical direction, the user can select "Vertical", "Horizontal"...

  • Page 72: Chapter 5 Accessories

    Chapter 5 Accessories 5.1 Digital IR Conference Room Switcher 5.1.1 Functions and indications Front panel of HCS-5300MX Rear panel of HCS-5300MX Figure 5.1 HCS-5300MX Digital IR Conference Room Switcher 1. Mains switch 7. Input channels（1-4） 2. 16×2 segment LCD For connecting to HCS-5300M Digital IR Wireless 3.

  • Page 73: Connection

    5.1.2 Connection Several meeting rooms can be split/combined at leisure through the HCS-5300MX Digital IR Conference Room Switcher with CBL6PS cable. One HCS-5300MX can combine up to four meeting rooms. The system can be controlled easily by a central control system. Figure 5.2 Splitting/Combining several meeting rooms with the HCS-5300MX Digital IR Conference Room Switcher...

  • Page 74: Configuration And Operation

    5.1.3 Configuration and operation Switch on HCS-5300MX Digital IR Conference Room Switcher, it will start initialization: When the initialization is finished, the corresponding state of input channels and output groups will be displayed on the LCD: Press the button at the front panel and go to the next operation: Press the “Menu”...

  • Page 75: Accessories

    5.2 Accessories 5.2.1 HCS-5300BAT Lithium battery Disassemble procedure: HCS-5300 can be power supplied by specific Lithium battery or power adaptor. 1. Press and hold the buckles on the right and left side of the battery; 2. Plug the battery out according to the arrow direction on the battery.

  • Page 76: Charging Device

    Figure 5.8 HCS-5300HT/CHG charging base 5.4 Power Adapter Connect the HCS-ADP15V to the power adapter Figure 5.7 HCS-5300CHG/08 charging unit interface at the bottom of the HCS-5300 series digital infrared wireless conference unit. Figure 5.7: 1. Charging indicating light 2. Fully charged indicating light 3.

  • Page 77: Dedicated Extension Cable For Digital Infrared Transceiver

    5.5 Dedicated extension cable for digital 5.6 Tripod infrared transceiver CBL5300 dedicated cable is used to connect the digital infrared transceiver and the digital infrared wireless conference main unit. It features one male 6P-DIN connector at one end and one female 6P-DIN connector at the opposite end.

  • Page 78: Earphones

    5.7 Earphones HCS-5100PB headphone The earphones are connected to the conference units via an Ø 3.5 mm stereo jack. Suitable earphone types include: EP-820AS single earphone Any other compatible type (see chapter 7, Technical EP-820BS/EP-828 single earphone Data). EP-920BS Earbuds HCS-5100PA headphone...

  • Page 79: Chapter 6 Fault Diagnosis

    Chapter 6 Fault diagnosis Some simple trouble-shooting instructions are provided in this chapter. If more serious faults arise, please contact a qualified technician. 6.1 Digital infrared wireless conference unit Fault Analysis Solution The battery is not charged when leaving The battery is not charged. the factory, please fully charge the battery (When using the lithium-ion battery) Cannot startup.

  • Page 80: Digital Infrared Wireless Main Unit

    The power indicating light is unit. not on when the power is on. Change the fuse. The fuse has blown. Please contact the local TAIDEN service center. The charging indicating light of Plug-in the battery properly into the The battery is not properly plugged-in.

  • Page 81: Chapter 7 Technical Data

    Chapter 7 Technical data 7.1 System specification System environmental conditions System performance Conforms to IEC 60914, the international standard for Working conditions fixed/stationary/transportable conference systems Temperature range: The carrier frequency transmitted by the main unit - Transport: -40 °C to +70 °C conforms to IEC 61603-7, the international standard for - Operating: 0 °C to +45 °C digital infra-red transmission of audio signals for...

  • Page 82: Digital Infrared Wireless Main Unit

    7.2 Digital infrared wireless main unit Type HCS-5300MA/20 HCS-5300MB/20 HCS-5300MC/20 Discussion √ √ √ Voting √ Simultaneous interpretation 1+3 channels 1+3 channels America, Japan: AC 110 V-120 V 60 Hz Mains voltage Asia, Europe: AC 220 V-240 V 50 Hz Power consumption Max.

  • Page 83: Digital Infrared Transceiver

    7.3 Digital infrared transceiver 7.3.1 Digital infrared transceiver HCS-5300TD HCS-5300TDS Type HCS-5300TDB HCS-5300TD-W HCS-5300TD-N HCS-5300TDS-W HCS-5300TDS-N 33 V DC (supplied from HCS-5300M/20) Voltage Max. 550 mA Current consumption Tripod, wall or ceiling mounted Tripod Suspension Mounting Wavelength 870 nm Modulation DQPSK method Carrier...

  • Page 84: Digital Infrared Receiver

    7.3.2 Digital infrared receiver Type HCS-5300RA HCS-5300RB Voltage 33 V DC(supplied from HCS-5300M/20) Current consumption Max. 30 mA Mounting Suspension Tripod, wall or ceiling mounted Wavelength 870 nm Modulation method DQPSK 2-8 MHz Carrier frequency Vertical: 150° (75°+75°), Acceptance angle Horizontal: 360°...

  • Page 85: Digital Infrared Wireless Conference Unit

    7.4 Digital infrared wireless conference unit 7.4.1 Digital infrared wireless conference unit Type HCS-5300C/CE HCS-5300D/DE HCS-5301D HCS-5302D HCS-5302C Discussion √ √ √ √ √ Voting 5 keys 2×（1+3） Simultaneous interpretation 1+3 channels 1+3 channels channels Priority key √ √ Voltage 11.1 V DC (HCS-5300BAT battery);...
  • Page 86 Type HCS-5300C/CE HCS-5300D/DE HCS-5301D HCS-5302D HCS-5302C Dimensions Weight (excl. battery) 0.46 kg Weight (incl. battery) 0.78 kg Color Silver/ Charcoal gray Type Uni-directional electret condenser microphone Sensitivity -46 dBV/Pa Frequency response 30-20000 Hz Directivity 0°/180° >20 dB (1kHz) Equivalent noise 20 dBA (SPL) Maximum sound 125 dB (THD<3%)

  • Page 87: Digital Ir Wireless Transmitter And Headset

    7.4.2 Digital IR wireless transmitter and headset Type HCS-5300HT+HCS-5300HS Discussion √ Voltage 7.4 V DC (HCS-5300BAT battery) Wavelength 870 nm (AM: Brightness modulation) Modulation method DQPSK Control channel：3.8 MHz Audio channel 1：4.3 MHz Carrier frequency Audio channel 2：4.8 MHz Audio channel 3：5.8 MHz Audio channel 4：6.3 MHz Emission angle Straight up ±...

  • Page 88: Digital Ir Conference Room Switcher

    7.5 Digital IR Conference Room Switcher Type HCS-5300MX America, Japan: AC 110 V - 120 V 60 Hz Mains voltage Asia, Europe: AC 220 V - 240 V 50 Hz 15 W Power consumption 4 6P-DIN sockets Input interfaces 20 6P-DIN sockets in 4 groups, 5 sockets per group Output interfaces Dimensions Weight...

  • Page 89: Charging Device

    7.7 Charging Device HCS-5300HT\CHG Type HCS-5300CHG/08 America, Japan: AC 110 V-120 V 60 Hz Mains voltage 15 V DC (HCS-ADP15V power adapter) Asia, Europe: AC 220 V-240 V 50 Hz Power Max. 380 W 15 W consumption Charging Time Approx. 6 hours Approx.

  • Page 90: Distributor

    7.9 Distributor Type HCS-5352 HCS-5352R Voltage 33 V DC (supplied from HCS-5300M) Number of I/O terminals 1 In / 4 Out 4 x 6P-DIN socket + 1 m cable with 4 x 4P-DIN socket + 1 m cable with Connector 6P-DIN plug 6P-DIN plug Dimensions...

  • Page 91: Earphones

    7.12 Earphones 7.13 Connection details EP-820AS Single Earphone Mains cables Used with the receiver/conference unit Blue Neutral Hi-Fi sound quality Brown Live Ø 3.5 mm stereo plug Green/Yellow Earth/Ground 32 Ω (Tip and Sleeve, Ring: NC) Frequency response: 50 Hz to 20 kHz Audio cables Sensitivity: ≥102 dBA/1 mW Chinch connector (male)

  • Page 92: Display Language List

    7.14 Display language list № Chinese English Abbr. № Chinese English Abbr. № Chinese English Abbr. Floor Azerbaijani Galician 原声 阿塞拜疆语 加利西亚语 阿尔巴尼亚 Albanian 巴利语 Balinese 古吉特语 Gujarati Arabic Bengali Hawaiian 阿拉伯语 孟加拉国语 夏威夷语 Bulgarian Burmese Kannada 保加利亚语 缅甸语 坎那达语 加泰罗利亚...

  • Page 93: Product Index

    HCS-5300RB Digital Infrared Receiver (ceiling, wall or tripod- mounted, excl. tripod when ordered) Distributor HCS-5352 Cable Splitter (1 input & 4 outputs, for HCS-5300 series transceiver) HCS-5352R Cable Splitter (1 input & 4 outputs, for HCS-5300 series receiver) Mounting Suspension HCS-5300TDP-05 Mounting Suspension for Digital Infrared Transceiver (0.5 m)
  • Page 94 Product index (continued) Lithium Rechargeable Battery Pack HCS-5300BAT Lithium Rechargeable Battery Pack (for HCS-5300 series conference unit) HCS-5300HT-BAT Lithium Rechargeable Battery Pack (for HCS-5300HT portable digital IR transmitter) Charging Device HCS-5300CHG/08 Charging Unit (8 pcs/case) HCS-5300HT/CHG Digital IR Receiver Charging Base...
  • Page 95 TAIDEN INDUSTRIAL CO.,LTD. Copyright by TAIDEN Last Revision: 09/2011...

Table of Contents