Automatic Start Up - Harman Accentra Pellet Insert Installation & Operating Manual

ig. 1
1. Fines are small pieces of broken pellets (sawdust). Fines do
not flow easily and often build up on the hopper funnel bottom
angles. These fines can be pushed into the feeder opening and
then fill the hopper with pellets. As the system works, they will
be burned.
2. The "TEST" cycle will operate the feed motor for exactly one
minute. Turning to "TEST" again and again may load too much
fuel into the burn pot causing excessive smoke on start-up.
3. The firebox low pressure switch will not allow the auger motor
or the igniter element to operate if the view door is open.
4. Adjust Feed Rate. If this is your first fire or you are trying different
pellets, set the feed adjuster to #4, Fig. 1. This is a conservative
number and will probably need to be increased. After you know
a feed rate setting that works well, use that setting. Remember,
if your feed rate is too high you may waste fuel.
5. This is usually a weekly maintenance procedure. Cleaning the
burn pot with the scraper with a small amount of new fuel in the
bottom is not a problem. First, scrape the ashes off the front of
the burn pot into the ash pan. Then scrape the holed surface
downward into the burn pot. When the stove feeds, these
scrapings will be pushed out by the feeder.
6. The ash pan can hold the ashes from approximately 1 ton of
premium fuel. This means the ashes will only need to be emptied
a few times a year.
7. Setting the feed adjuster # for maximum burn: With the unit
burning in "AUTO", turn to "Stove Mode" and put the fan on
"H". Set the Temperature Dial to #7. Allow the unit to burn for
about 30 minutes and check ash on front of burn pot. Fig. 2.
If the ash line is larger than 1", turn the feed adjuster from #4
to #5. Allow another 30 minutes of burn time and check again.
If, at #6 setting, a 1" or less ash bed is not obtainable, it is not
a problem. The 1" ash bed is only at maximum burn rate and
during normal operation, the ash bed will be larger.

Automatic Start Up

Igniter Switch to " AUTO" (up position)
only light lit.
See Note 7.
the ash pan prior to lighting.
1"
1. Turn
2.
5. Turn eed Ad uster to # .
ig. 2
7. Turn the Temperature ial to the desired room temperature.
8. Turn
operation.
do so will affect operation of the appliance and may permit
escape of smoke or gases into the living space.
NEV ER USE G ASOLINE, G ASOLINE-TY PE LANTER N
F UEL, K ER OSENE, CHAR COAL LIG HTER F LUID, OR
SIMILAR LIQ UIDS TO STAR T OR ' F R ESHEN UP' A F IR E
IN THIS HEATER . K EEP ALL SUCH LIQ UIDS W ELL
A W AY F R OM THE HEATER , W HILE IN USE.
Starting F irst F ire
ake sure the unit is plugged into a properly grounded, 120
AC, 0 Hz electrical source. The power light should be the
te Be ure t ere n
ode Selector to O
ill hopper with pellets.
. Clean burn pot with scraper, if necessary.
. If starting after an empty hopper, turn eed Ad uster to
TEST (for one 0 second cycle).
into the auger tube and also allow you to check the motors
for operation. NOTE: The auger motor will not operate
t t e e r r
. lip the Igniter Switch up into the AUTO position.
ode Selector to Room Temperature or Stove
Temperature.
. ill hopper with pellets and remove ashes as required.
eep the hopper lid and firebox doors closed while in
aintain door seals in good condition. ailure to
W AR NING
BU R NIN G G A R BA G E, USE OF
F IR E STAR TER S OR ALTER ING
HI G HE R HEAT OUTPUT MAY CAUSE DAMA G E TO THE
STOV E AND COULD R ESULT IN A HOUSE F IR E. USE
ONLY APPR OV ED F UELS AND F OLLOW
OPER ATION G UIDELINES.
W AR NING
ue r t er c m u t
.
This will flow pellets
2
pper pen
IMP R OPE R F UELS,
THE STOV E F OR
ONLY THESE
3 -9 0 -0 0 6 7 4 R 2 7 _ 8 /1 3
4
e n