Howv - JVC HR-S9400E Instructions Manual

ENTER SHOWVIEW
NUMBER
4
Press OK, and a cursor
appears above "GUIDE
PROG". Then, using the
NUMBER keys, input the
S V number (found
HOW IEW
in most TV listings) of a
program scheduled to be
broadcast on each station
on the list from step 1,
starting at the top. If you
enter the wrong number,
press CANCEL to backspace
and input the correct number.
CONFIRM CHANNEL
POSITION NUMBER
5
Press OK and the display
4
under "TV PROG" begins
blinking.
If the blinking number
under "TV PROG" agrees
with the channel
position . . .
. . . press OK.
If the numbers do not
agree . . .
. . . input the channel position using PUSH JOG % fi or
the NUMBER keys, then press OK.
If you input the S
has already aired, "ERROR" appears on screen for a
few seconds. Input the correct S
Repeat steps 4 and 5 as necessary.
CLOSE MENU
6
Press MENU and selection is complete.
If you already know the Guide Program number for a station . . .
1– After step 3, press PUSH JOG .
The GUIDE PROG number begins blinking.
2– Enter the Guide Program number using the NUMBER keys
or PUSH JOG% fi , then press PUSH JOG
The TV PROG number begins blinking.
3– Enter the channel position using the NUMBER keys or
PUSH JOG% fi , then press PUSH JOG
Repeat 2 and 3 as necessary.
4– Press MENU.
GUIDE PROG SET
1 2 3 4 5
GUIDE PROG TV PROG
1
[0-9] =
[MENU] : EXIT
When entering a S
number for ZDF
GUIDE PROG SET
GUIDE PROG TV PROG
2
[ 5 ∞] =
[MENU] : EXIT
V number of a program that
HOW IEW
V number.
HOW IEW
.
.
When Using A Satellite
Tuner
Satellite Antenna
Ex. 1
Satellite
1
Tuner
AV2 IN/
V
HOW IEW
DECODER
TV Receiver
2
Preparation
1– Connect the satellite tuner to the AV2 IN/DECODER
connector on the rear of your recorder.
2– Set "AV2 SELECT" to "AV2" (
To Record Satellite Broadcasts . . .
1– Select the appropriate channel on the satellite tuner.
2– Set your recorder's input mode to "AUX2". (
3– Start recording (
To Record Satellite Broadcasts Using S
Recording . . .
1– Set your recorder's input mode to "AUX2". (
2– Perform Guide Program Number setting.
In step 5 in the left column, press NUMBER key "0" to set
"TV PROG" to "AUX2".
3– Perform S
To Record Satellite Broadcasts Using Regular Timer Recording . . .
1– In step 6 on page 31, press TV PROG +/– to set the channel
position to "AUX2".
NOTES:
When timer-recording a satellite programme, first set the
satellite tuner to the appropriate channel before the selected
programme begins and then set the satellite tuner's timer. If
your satellite tuner does not have a timer, leave it switched on.
If your recorder's front panel VIDEO and/or AUDIO connec-
tors are being used, they take priority and "AUX2" cannot be
selected. Make sure no cables are connected to the front
panel connectors when performing this procedure.
Aerial or Cable
Ex. 2
Satellite
Tuner and
Decoder
pg. 35).
pg. 23, steps 3 – 6).
HOW
V Timer Recording (
HOW IEW
13
EN
Rear view
For Customers in
Australia and
New Zealand:
When connecting
the AV cable, use
the input and/or
output cable
adapter.
pg. 35)
V Timer
IEW
pg. 35)
pg. 28).