Putting Into Operation - Bosch GCM 10 Operating Instructions Manual

GCM10_ASIA.book Seite 9 Dienstag, 18. September 2007 9:40 09
Standard Horizontal Miter Angles
(see Figure )
J
For quick and precise setting of often used miter an
gles, detents 14 are provided on the saw table:
Left 15°
0°
Right 15°
Place the machine in the working position.
Loosen the locking knob 12 in case it is tightened.
Pull the lever 13 and turn the saw table 15 to the de
sired miter angle to the right or the left. Release the le
ver. The lever must be felt to engage in the detent.
Variable Horizontal Miter Angle
The horizontal miter angle can be set in the range from
48° (left side) to 48° (right side).
Place the machine in the working position.
Loosen the locking knob 12 in case it is tightened.
Pull the lever 13 and press the locking clamp 11 at the
same time until it engages in the groove provide for this
purpose (see the illustration
saw table becomes freely moveable.
Rotate the saw table 15 to the left or right and set the
desired miter angle with the aid of the fine scale 10.
Retighten the locking knob 12.
Fine scale
With the fine scale 10, the horizontal miter angle can
be set with an accuracy of up to ¼°.
Desired Setting of Align the Fine
the Initial Angle x Scale Mark
(Scale 10)
x,25 °
x,5 °
x,75 °
Example:
To set to a miter angle of 40.5°, the ½° mark of the fine
scale 10 must be aligned with the 42° mark of the
scale 9.
1 619 P04 359 • (2007.09)
22,5° 31,6° 45°
22,5° 31,6° 45°
). In this manner, the
K
... with the
Mark (Scale 9)
¼° x + 1°
½° x + 2°
¾° x + 3°
English–9
Standard Vertical Bevel Angles
(see Figure )
L
For quick and precise setting of often used bevel an
gles, stops are provided for the angles of 0°, 33.9° and
45°.
Place the machine in the working position.
Loosen the clamping handle 32.
For the standard angles of 0° or 45°, swing the tool
arm with the handle 1 to the stop at the upper or the
lower end of the elongated hole 33.
For the standard angle of 33.9°, press the setting knob
31 completely in. Then swing the tool arm with the
handle 1 until the pin 24 rests against the stop bolt 23.
Retighten the clamping handle 32.
Variable Vertical Bevel Angle
(see Figure )
M
The vertical bevel angle can be set in the range from
0° to 45°.
Loosen the clamping handle 32.
Swing the tool arm with the handle 1 until the angle in
dicator 47 points to the desired bevel angle.
Hold the tool arm in this position and retighten the
clamping handle 32.

Putting into Operation

Switching On and Off
To put into operation, pull the on/off switch 2 in the
direction of the handle 1.
For safety reasons, the on/off switch of the ma
chine cannot be locked on but must remain de
pressed during operation.
For sawing, press in addition the locking lever 3. (see
the Figure
N
)
Only by pressing the locking lever can the tool arm be
guided downward.
To switch off the machine, release the on/off switch
2.
0 601 B20 037 (Australia)
To put into operation, slide the switch lock in the di
rection of the tool arm. Then press the on/off switch 2
and hold it depressed.
For safety reasons, the on/off switch of the ma
chine cannot be locked on but must remain de
pressed during operation.
To switch off the machine, release the on/off switch
2.