Using The Dvd Multi Playback Mode; Activating The Dvd Multi Playback Mode - JVC RX-9000VBK Instructions Manual

Using the DVD MULTI Playback Mode

This receiver provides the DVD MULTI playback mode for reproducing the analog discrete output mode of the DVD
player. Before playing back a DVD, refer also to the manual supplied with the DVD player.
The following operations are only possible while the receiver is ready for the main room operations, and are only used
for the main room source — DVD MULTI.
IMPORTANT:
When using the buttons and controls on the front panel:
Check the following lamps' illumination.
For the main room operations:
• The MAIN ROOM ON/OFF lamp is lit.
• The SUB ROOM CONTROL lamp is not lit.
When using the remote control:
Check to see if the multi-room operation selector and the remote
control mode selector are set to the correct positions:
• Multi-room operation selector:
To operate this receiver for the main room,
set it to "MAIN ROOM."
• Remote control mode selector:
To operate this receiver, set it to "AUDIO/TV/
VCR."

Activating the DVD MULTI Playback Mode

You can adjust the DVD MULTI playback mode while playing back
a DVD using the analog discrete output mode on the DVD player.
Once you have made adjustments, the receiver memorizes the
adjustments until you change them. You also need to set the DVD
player to the analog discrete output mode.
Before you start, remember...
• There is a time limit in doing the following steps. If the setting is
canceled before you finish, start from step 1 again.
On the front panel:
1. Turn SOURCE SELECTOR until
"DVD MULTI" appears on the
display.
Notes:
• When you select "DVD MULTI" as the main room source to play,
the DSP mode is canceled temporarily, and the SURROUND
ON/OFF and DSP MODE buttons do not work.
• When the SUB ROOM ON/OFF lamp and the SUB ROOM
speaker (SPEAKERS 2) lamp on the front panel are lit green,
you cannot select "DVD MULTI" as the main room source.
2. Select the analog discrete output mode on the
DVD player, and start playing a DVD.
• Refer to the manual supplied with the DVD player.
If you need to make any adjustment, go to the following
steps.
3. Adjust the speaker output levels.
1) Press BALANCE/SURROUND
ADJUST repeatedly until one of the
indications appears on the display.
"CENTER LEVEL":
"REAR L LEVEL":
"REAR R LEVEL":
MAIN SUB
ROOM ROOM
2) Turn MULTI JOG to adjust the
selected speaker output level (from –10
AUDIO/
TV/VCR
dB to +10 dB).
3) Repeat 1) and 2) to adjust the other
CATV/DBS
speaker output levels.
From the remote control:
1. Press DVD MULTI so that "DVD
MULTI" appears on the display.
Notes:
• When you select "DVD MULTI" as the main room source to play,
the DSP mode is canceled temporarily, and the SURROUND
ON/OFF and DSP MODE buttons do not work.
• When the SUB ROOM ON/OFF lamp and the SUB ROOM
speaker (SPEAKERS 2) lamp on the front panel are lit green,
you cannot select "DVD MULTI" as the main room source.
2. Select the analog discrete output mode on the
DVD player, and start playing a DVD.
SOURCE SELECTOR
• Refer to the manual supplied with the DVD player.
If you need to make any adjustment, go to the following
steps.
3. Press SOUND.
The 10 keys are activated for adjusting the sound.
4. Adjust the speaker output levels.
• To adjust the center speaker level, press CENTER –/+ (from –
10 dB to +10 dB).
• To adjust the left rear speaker level, press REAR•L –/+ (from
–10 dB to +10 dB).
• To adjust the right rear speaker level, press REAR•R –/+ (from
–10 dB to +10 dB).
2
To adjust the center speaker level.
To adjust the left rear speaker level.
To adjust the right rear speaker level.
REAR•L
CENTER
5
3
ENTER ENTER
MENU MENU
BALANCE/SURROUND
ADJUST
MULTI JOG
DVD MUILTI
SOUND
REAR•R
8 9
6
41