JVC RX-9000VBK Instructions Manual page 61

IMPORTANT:
To operate JVC's video components using this remote control:
• You need to connect JVC video components through the AV
COMPU LINK terminals (see page 54) in addition to the
connections using cables with RCA pin plugs (see pages 7 and 8).
• Some JVC VCRs can accept two types of the control signals —
remote codes "A" and "B." Before using this remote control, make
sure that the remote control code of the VCR connected to the
VCR 1 jacks is set to code "A."
– When another JVC VCR is connected to the CDR/VCR 2 jacks,
set its remote control code to code "B." (This remote control
cannot emit the control signals of code "B.")
• To operate the video components only using this remote control,
aim the remote control at the remote sensors on the target video
component(s) directly. (For the TV having AV COMPU LINK
terminal "RECEIVER/AMP," aim the remote control directly at
the remote sensor on the receiver.)
• To operate the video component(s) using the RF signals emitted
from this remote control, the IR signal transmitter and the RF rod
antenna must be connected to this receiver.
– Place the IR signal transmitter so that it is aimed at the remote
sensor on the target video component(s).
– The RF signal-reachable distance may differ depending on the
operating conditions and circumstances.
– The IR signal transmitter can send signals at a distance of 10
feet (3 m).
MAIN SUB
ROOM ROOM
MAIN ROOM SUB ROOM
ON/OFF ON/OFF
MAIN SUB
DVD DVD MUILTI
ROOM ROOM
TV/DBS VIDEO
VCR 1 CDR/VCR 2 ANALOG/DIGITAL
Check to see if the
multi-room
SURROUND CNTR TONE
operation selector
1
ON/OFF
REAR TONE
is set to the SURROUND
4
MODE
correct position.
CD-DISC SEA MODE
7
To operate the
SOUND
TEST
receiver for the
10
RETURN
main room, set it
to "MAIN ROOM."
To operate the MENU
receiver for the
sub-room, set it
EXIT
to "SUB ROOM."
TV VOL CHANNEL
TV/VIDEO VCR 1
/REW
DOWN
REC
RM-SRX9000J
STANDBY ON
TV/CATV/DBS VCR 1
POWER POWER
CD TAPE/MD
PHONO FM/AM
SLEEP
CENTER
2 3
MENU MENU
REAR-L
5 6
ENTER ENTER
REAR-R
8 9
/P
SUBWOOFER
0 +10
AUDIO/
FM MODE 100+
TV/VCR
AUDIO/
TV/VCR
CATV/DBS
CATV/DBS
SET
TEXT
DISPLAY
Check to see if the
remote control
mode selector is set
VOLUME
to the correct
position.
TAPE/MD MUTING
To operate the
CONTROL
audio system, TVs,
PLAY
FF/
VCRs, and DVD
TUNING UP
STOP PAUSE
players, set it to
"AUDIO/TV/VCR."
REMOTE CONTROL
VCR 1 (VCR connected to the
VCR 1 jacks)
You can always perform the following operations (with the remote
control mode selector set to "AUDIO/TV/VCR"):
VCR 1 POWER: Turns on or off the VCR 1.
After pressing VCR 1 or VCR 1 CONTROL (with the remote
control mode selector set to "AUDIO/TV/VCR"), you can perform
the following operations on the VCR 1:
1 – 9, 0:
Selects the TV channels on VCR 1.
PLAY: Starts playing.
REW: Rewinds a tape.
FF:
Fast winds a tape.
STOP:
Stops operations.
PAUSE: Pauses playing. To release it, press PLAY.
¶ REC:
Press this button with the PLAY button to start
recording. (Only for the main room operations)
Press this button with the PAUSE button to enter
recording pause.
CHANNEL +/–:
Changes the TV channels on the VCR.
Note:
You can use either VCR 1 button or the VCR 1 CONTROL button to
activate the buttons listed above. If you press VCR 1, the playing
source also changes. On the other hand, if you press VCR 1
CONTROL, the playing source does not change.
DVD player
After pressing DVD (or DVD MULTI: only for the main room
operations) (with the remote control mode selector set to "AUDIO/
TV/VCR"), you can perform the following operations on a DVD
player:
PLAY:
Starts playing.
4:
Returns to the beginning of the current (or previous) track.
¢:
Skips to the beginning of the next track.
STOP:
Stops playing.
PAUSE: Stops playing temporarily. To release it, press PLAY.
After pressing DVD (or DVD
MULTI: only for the main room
operations), these buttons can be
used for the DVD menu operations.
Note:
For detailed menu operations, refer to the instructions supplied
with the discs or the DVD player.
TV
You can always perform the following operations only for the main
room operations (with the remote control mode selector set to
"AUDIO/TV/VCR"):
TV/CATV/DBS POWER:
Turns on or off the TV.
TV VOL +/–: Adjusts the volume.
TV/VIDEO: Sets the input mode (either TV or VIDEO).
After pressing TV/DBS (with the remote control mode selector set
to "AUDIO/TV/VCR"), you can perform the following operations
on a TV:
CHANNEL +/–: Changes the channels.
1 – 9, 0, 100+: Selects the channels.
RETURN: Alternates between the previously selected channel
and the current channel.
CENTER
2 3
MENU MENU
REAR TONE REAR-L
4 5 6
ENTER ENTER
REAR-R
8
59