Selecting The Main Room Source To Play - JVC RX-9000VBK Instructions Manual

To use this receiver for the main room operations again, press
MAIN ROOM ON/OFF again.
The MAIN ROOM ON/OFF lamp on the front panel lights red, and
the currently selected Front speaker lamps on the front panel also
light red.
Notes:
• If you have turned off the receiver with the volume level set at more
than level "30," the volume level will be automatically set at level
"30" next time you turn on the receiver.
• If "TURN ON MAIN OR SUB ROOM" appears on the display, press
MAIN ROOM ON/OFF or SUB ROOM ON/OFF to listen the sound
in the main room or in the sub-room; otherwise, the receiver will
turn off after about 1 minute.

Selecting the Main Room Source to Play

On the front panel:
Turn SOURCE SELECTOR until the source
name you want appears on the display.
• As you turn the selector, the source changes as
follows:
CD O PHONO O TAPE (or MD) O FM O AM O DVD O
DVD MULTI O TV SOUND (or DBS) O VCR 1 O
CDR/VCR 2 O VIDEO O (back to the beginning)
The selected source lamp also lights up.
DVD
TV SOUND/DBS
VCR 1
CDR/VCR 2
VIDEO
• The DVD lamp lights up both for "DVD" and
"DVD MULTI."
From the remote control:
Press one of the source selecting buttons.
DVD DVD MUILTI
TV/DBS VIDEO
VCR 1 CDR/VCR 2
Selected source name appears
16
SOURCE SELECTOR
CD
PHONO
TAPE/MD
FM
AM
CD TAPE/MD
PHONO FM/AM
DVD Select the DVD player.
DVD MULTI
Select the DVD player for viewing the digital video
disc using the analog discrete output mode (5.1 CH
reproduction) on the DVD player.
To enjoy the DVD MULTI playback, see page 41.
CD *
Select the CD player.
TAPE/MD * Select the cassette deck (or the MD recorder).
TV/DBS
Select TV sounds (or the DBS tuner).
VIDEO
Select video component connected to the VIDEO
jacks.
PHONO * Select the turntable.
FM/AM *
Select an FM or AM broadcast.
• Each time you press the button, the band alternates
between FM and AM.
VCR 1
Select the video component connected to the VCR 1
jacks.
CDR/VCR 2 * Select the CD recorder or video component
connected to the CDR/VCR 2 jacks.
Notes:
• When connecting an MD recorder (to the TAPE/MD jacks), and a
DBS tuner (to the TV SOUND/DBS jacks), change the source
name shown on the display. For details, see page 23.
• When you press one of the source selecting buttons on the remote
control marked above with an asterisk ( * ), the receiver
automatically turns on.
Signal and speaker indicators on the display
• The signal indicators light up to indicate the incoming channel
signals.
– Only the indicators for the incoming signals light up.
• The frame of the signal indicator (except for "LFE" and "S")
lights up if the corresponding speaker is set to "LARGE" or
"SMALL" (for subwoofer, "YES").
– The frames of "L" and "R" indicators always light up.
L C
SUBWFR
LS S
L: • When digital input is selected: Lights up when the left
channel signal comes in.
• When analog input is selected: Always lights up.
R:
• When digital input is selected: Lights up when the right
channel signal comes in.
• When analog input is selected: Always lights up.
C:
Lights up when the center channel signal comes in.
LS: Lights up when the left rear channel signal comes in.
RS: Lights up when the right rear channel signal comes in.
S:
Lights up when the monaural rear channel signal comes in.
LFE: Lights up when the LFE channel signal comes in.
Notes:
• When "SUBWOOFER" is set to "YES,"
• When you select "DVD MULTI," all the signal indicators except "S"
light up.
R
LFE
RS
lights up.
SUBWFR