Sub-Room Operations; Turning The Power On And Off (Standby) And Selecting The Sub-Room Operations - JVC RX-9000VBK Instructions Manual

Sub-Room Operations

This section explains only the operations used when you play any sound source in the sub-room.
See pages 15 for the main room operations.
IMPORTANT:
When using the buttons and controls on the front panel:
Check the following lamps' illumination.
For the sub-room operations:
• The SUB ROOM ON/OFF lamp is lit.
• The SUB ROOM CONTROL lamp is lit.
When using the remote control:
Check to see if the multi-room operation selector and the remote
control mode selector are set to the correct positions:
Multi-room operation selector:
To operate this receiver for the sub-room, set it
to "SUB ROOM."
Remote control mode selector:
To operate this receiver, set it to "AUDIO/TV/
VCR."
Turning the Power On and Off (Standby)
and Selecting the Sub-room Operations
On the front panel:
1. Press POWER.
The STANDBY lamp on the front panel goes
off, and the MAIN ROOM ON/OFF lamp on
the front panel lights red. The name of the
current main room source (or station
frequency) appears on the display.
Current source name for main room appears
Current volume level for main room is shown here
The currently selected SPEAKERS 1 (MAIN ROOM) and/or
SPEAKERS 2 (SUB ROOM) lamps on the front panel also light
red.
2. Press SUB ROOM ON/OFF.
The SUB ROOM ON/OFF lamp on the
button lights green (and the SUB ROOM
speaker (SPEAKERS 2) lamp on the front
panel also lights green if it has been
activated).
• If the SUB ROOM speaker (SPEAKERS 2) lamp on the front
panel is not lit, see also "Setting the Front Speakers Either for
the Main Room or Sub-room" on page 23, and "Activating the
Sub-room Front Speakers" on page 22.
20
3. Press SUB ROOM CONTROL.
The SUB ROOM CONTROL lamp on the
button lights green.
The name of the current source (or station
frequency) for the sub-room appears on the
display.
Current source name for sub-room appears
MAIN SUB
ROOM ROOM
AUDIO/
TV/VCR
Now the buttons and controls on the front panel work for the
sub-room operations.
CATV/DBS
• Each time you press the button, the lamp on the button turns
on and off.
To turn off the power (into standby mode),
press POWER again.
The STANDBY lamp lights red. A small amount
of power is consumed in standby mode. To turn
STANDBY
the power off completely, unplug the AC power
cord.
POWER
From the remote control ONLY:
1. Set the multi-room operation
MAIN ROOM
ON/OFF
selector to "SUB ROOM."
Now the buttons on the remote control work
for the sub-room operations.
2. Press AUDIO POWER ON.
The STANDBY lamp on the front panel
goes off, and the SUB ROOM ON/OFF
lamp on the front panel lights green (and
the SUB ROOM speaker (SPEAKERS 2)
lamp on the front panel also lights green if
it has been activated).
• If the SUB ROOM speaker (SPEAKERS 2) lamp on the front
panel is not lit, see "Activating the Sub-room Front Speakers"
on page 22.
SUB ROOM
ON/OFF
To turn off the power (into standby mode),
press AUDIO POWER STANDBY.
The STANDBY lamp lights red, and the SUB
ROOM ON/OFF lamp on the front panel goes
off.
Note:
If you have turned off the receiver with the volume level set at more
than level "30," the volume level will be automatically set at level "30"
next time you turn on the receiver.
SUB ROOM
CONTROL
Current volume level for sub-room is
shown here
MAIN
ROOM
STANDBY
SUB ROOM
ON/OFF
STANDBY
STANDBY
POWER
SUB
ROOM
ON
ON