Advertisement
Internal Web Pages
To configure IN1608 scalers using the factory-installed Web pages in a
Web browser, connect the Ethernet port on the device to a LAN or WAN
(see the example to the right). The default IP address is 192.168.254.254.
The default subnet mask is 255.255.0.0.
Extron Product Configuration Software
To configure IN1608 scalers using the Extron Product Configuration
Software (PCS), install the software (available on the Extron website,
www.extron.com) to a PC connected to the scaler via Ethernet or front
panel USB Config port. After the installation, start the program. For full
instructions, press <F1> on the keyboard or click the ? button in the
software and select Help File.
Firmware Upgrades
The firmware of the scaler can be upgraded via the internal Web pages or the Extron Firmware Loader program (available at www.extron.com).
Basic SIS Command Table
IN1608 scalers can be configured with specific SIS commands via an RS-232, USB, or Ethernet connection. Use the Extron DataViewer utility
or a control system to send and receive SIS commands. The table below lists a selection of SIS commands. For a full list of SIS commands and
variables, see the IN1606 and IN1608 Series User Guide at www.extron.com.
Command
Select audio and video input
Select video input only
Select audio input only
Execute Auto-Image™
Execute Auto-Image and fill
Execute Auto-Image and follow
Mute video to black
Mute video and sync
Unmute video and sync
NOTE:
By default, setting the audio mute with the following commands affects all outputs (configurable through group masters).
Set master audio mute
View master audio mute status
Enable executive mode 1
Enable executive mode 2
Disable executive modes
Set scaler IP address
Set scaler DHCP mode
Set subnet mask
Set gateway IP address
Reboot networking
NOTE:
IP settings will not take effect until the
NOTES:
X!
= Input selection (1-8)
X(
= Enable or disable (0 = off or disabled; 1 = on or enabled)
X4)
= IP address (xxx.xxx.xxx.xxx; 192.168.254.254 = default)
X4!
= Subnet mask (xxx.xxx.xxx.xxx; 255.255.0.0 = default)
X4@
= Gateway address (xxx.xxx.xxx.xxx; 0.0.0.0 = default)
Extron USA Headquarters
+1.800.633.9876 (Inside USA/Canada Only)
© 2014 Extron Electronics — All rights reserved. All trademarks mentioned are the property of their respective owners.
4
ASCII Command
Response
(Host to Device)
(Device to Host)
X!
!
In
X! •
X!
X! •
&
In
X!
$
In
X! •
A
]
Img0
1*A
]
Img1
2*A
]
Img2
1B
]
Vmt1
]
2B
Vmt2
0B
]
Vmt0
E
X(
}
D7*
GRPM
GrpmD07*
E
D7GRPM
}
X(]
1X
]
Exe1
2X
]
Exe2
0X
]
Exe0
E X4)
CI
}
Ipi
• X4)]
E X(
}
X(]
DH
Idh
E X4!
}
• X4!]
CS
Ips
E X4@
}
• X4@]
CG
Ipg
E
}
2BOOT
Boot2
E
}
2BOOT
command is executed.
Extron USA - West: +1.714.491.1500
Extron USA - East: +1.919.850.1000
Additional Description
All
]
Selects audio and video input
]
RGB
Selects the video only input
Aud
]
Selects the audio only input
Executes an Auto-Image on the current input.
Executes an Auto-Image and fills the output.
Executes an Auto-Image and maintains the aspect ratio of
the current input.
Mutes the video and displays a black output.
Mutes the video and sync output.
Unmutes the video.
X(]
Enable or disable master audio mute.
View the current master audio mute status.
Locks the entire front panel.
Locks the front panel except for input selection and volume
control.
Allows all front panel adjustments and selections.
Specifies a new scaler IP address.
Enables or disables DHCP (0 = default).
Specifies a new subnet mask.
Specifies a new gateway IP address.
]
Restarts the network connection after IP or DHCP changes.
FAX: +1.714.491.1517
FAX: +1.919.850.1001
X!
.
X!
.
X!
.
www.extron.com
68-1916-51 Rev. A
05 14
Advertisement
