Mazda 6 Training Manual page 143

DTC Table
DTC No.
P0500 VSS circuit malfunction (ATX)
P0706 Transale range (TR) switch circuit range/performance
P0707 Transale range (TR) switch circuit low input
P0708 Transale range (TR) switch circuit high input
Transale fluid temperature (TFT) sensor circuit range/
P0711
perfotmance
Transale fluid temperature (TFT) sensor circuit
P0712
malfunction (short to ground)
Transale fluid temperature (TFT) sensor circuit
P0713
malfunction (open circuit)
P0715 Input/turbine speed sensor circuit malfunction
P0731 Gear 1 incorrect (Incorrect Gear Ratio Detected)
P0732 Gear 2 incorrect (Incorrect Gear Ratio Detected)
P0733 Gear 3 incorrect (Incorrect Gear Ratio Detected)
P0734 Gear 4 incorrect (Incorrect Gear Ratio Detected)
P0741 Torque converter clutch (TCC) (stuck OFF)
P0742 Torque converter clutch (TCC) (stuck ON)
P0745 Pressure control solenoid malfunction
P0751 Shift solenoid A stuck OFF
P0752 Shift solenoid A stuck ON
P0753 Shift solenoid A malfunction (electrical)
P0756 Shift solenoid B stuck OFF
P0757 Shift solenoid B stuck ON
P0758 Shift solenoid B malfunction (electrical)
P0761 Shift solenoid C stuck OFF
P0762 Shift solenoid C stuck ON
P0763 Shift solenoid C malfunction (electrical)
P0766 Shift solenoid D stuck OFF
P0767 Shift solenoid D stuck ON
P0768 Shift solenoid D malfunction (electrical)
P0771 Shift solenoid E stuck OFF
P0772 Shift solenoid E stuck ON
P0773 Shift solenoid E malfunction (electrical)
P0841 Oil pressure switch circuit malfunction
Failure Detection Function
• The failure detection function compares input/output devices and system components operation to normal
condition values pre-programmed in the PCM.
• If a failure is detected, the HOLD indicator light flashes to warn the driver of a malfunction in the powertrain
system components or sensors/switches.
• The stored DTCs in the PCM are retrieved using the WDS or equivalent.
• The failures are detected according to the following detection concepts. Detection concepts of the TP sensor
malfunction (P0122, P0123) are mentioned in the ENGINE section.
Vehicle speed sensor (VSS) circuit malfunction (P0500)
• No VSS signal is input to PCM terminal 3C when engine coolant temperature is above 60 ° ° ° ° C {140 ° ° ° ° F} and
input/turbine speed sensor signal is above 1,500 rpm and selector lever position is at D, S or L range.
Transale range (TR) switch circuit range/performance (P0706)
• No TR signal (P, R, N, D, S or L range/position) Input to PCM terminal 1W when engine speed is above 530
rpm and vehicle speed is above 20 km/h {12 mph} and voltage at PCM terminal 1W is 0.5 V or above.
Transale range (TR) switch circuit low input (P0707)
• Input voltage from TR switch to PCM terminal 1W below 0.5 V when engine speed is above 530 rpm and
vehicle speed is above 20 km/h {12 mph}.
Transale range (TR) switch circuit high input (P0708)
• Input voltage from TR switch to PCM terminal 1W above 4.79 V when engine speed is above 530 rpm and
vehicle speed is above 20 km/h {12 mph}.
ON-BOARD DIAGNOSTIC
Condition
HOLD
indicator
MIL DC
light
flashes
ON YES 2
ON YES 2
ON YES 1
ON YES 2
ON NO 2
ON YES 1
ON YES 1
ON YES 1
OFF YES 1
OFF YES 1
OFF YES 1
OFF YES 1
OFF YES 1
OFF YES 1
OFF YES 1
ON YES 2
ON YES 2
ON YES 1
ON YES 2
ON YES 2
ON YES 1
ON YES 2
ON YES 2
ON YES 1
ON YES 2
ON YES 2
ON YES 1
ON YES 2
ON YES 2
ON YES 1
OFF NO 2
Monitor Memory
item function
CCM ×
CCM ×
CCM ×
CCM ×
CCM ×
CCM ×
CCM ×
CCM ×
CCM ×
CCM ×
CCM ×
CCM ×
CCM ×
CCM ×
CCM ×
CCM ×
CCM ×
CCM ×
CCM ×
CCM ×
CCM ×
CCM ×
CCM ×
CCM ×
CCM ×
CCM ×
CCM ×
CCM ×
CCM ×
CCM ×
CCM ×
K–17
K