Accessories - Lakeshore 330 User Manual

Lake Shore Model 330 Autotuning Temperature Controller User's Manual
6.3

ACCESSORIES

Accessories are devices that perform a secondary duty as an aid or refinement to the primary unit.
MODEL
NUMBER
106-009 * Heater Output Connector (Dual Banana Jack).
106-233 * Sensor Mating Connector (Quantity 2).
115-006 * Detachable 120 VAC Line Cord.
RJ-11 Cable Assembly. Four-Wire Cable Assembly with RJ-11 plugs on each end. Used with RS-232C
2001
Interface. Cable is 14 feet (4.6 meters) long. See Figure 6-1.
RJ-11 to DB-25 Adapter. Adapts RJ-11 receptacle to female DB-25 connector. Connects Model 622/647 to
2002
RS-232C Serial Port on rear of Customer's computer. See Figure 6-2.
RJ-11 to DE-9 Adapter. Adapts RJ-11 receptacle to female DE-9 connector. Connects Model 622/647 to RS-
2003
232C Serial Port on rear of Customer's computer. See Figure 6-3.
Heater Output Conditioner. A passive filter which further reduces already low Model 330 heater output noise.
Typical insertion loss for the Model 3003 is 20 dB (at 10 µV) at line frequency, and >40 dB from double the line
frequency up. The Model 3003 is housed in a 144 mm x 72 mm x 165 mm (5.67 x 2.84 x 6.5 inch) panel mount
enclosure and weighs 1.6 kg (3.5 lbs).
3003
The Model 3003 requires no external power. Take care not to reverse the polarity of the incoming heater signal.
An input protection diode acts as a short in case of reversed polarity. It is not necessary to use ground terminals
provided, but sometimes it helps reduce noise. Shorting out the filter input or output while the controller driving it
is turned on is not recommended; the Model 3003 may have a large stored charge.
Half-Rack Mounting Kit for One Model 330 Temperature Controller. Half-length mounting panel and
RM-3H1
mounting ears to attach one Model 330 to a 482.6 mm (19-inch) by 88.9 mm (3.5 inch) rack mount space.
See Figure 6-4.
Half-Rack Mounting Kit for One Model 330 Temperature Controller with Handles. Half-length mounting
RM-3H1-H
panel, mounting ears, and handles to attach one Model 330 to a 482.6 mm (19-inch) by 88.9 mm (3.5 inch)
rack mount space. See Figure 6-4.
Dual Mounting Shelf for Two Model 330 Temperature Controllers. Mounting brackets and ears to attach
RM-3H2
two Model 330 Temperature Controllers side-by-side on a 482.6 mm (19-inch) by 88.9 mm (3.5 inch) rack
mount shelf. See Figure 6-5.
Dual Mounting Shelf for Two Model 330 Temperature Controllers with Handles. Mounting brackets,
RM-3H2-H
ears, and handles to attach two Model 330 Temperature Controllers side-by-side on a 482.6 mm (19-inch) by
88.9 mm (3.5 inch) rack mount shelf. See Figure 6-5.
IEEE-488 (GPIB) Computer Interface Interconnect Cable Assembly. Connects two IEEE-488 devices. The
8072
cable is 1 meter (3.3 feet) in length.
8271-30 Sensor/Heater Cable Assembly. For Silicon Diode &100 Ω Platinum RTD Temperature Sensors.
Lake Shore Cryogenic Wire. Lake Shore sells these types of cryogenic wire: WNC = Nichrome Heater, WSL =
See Text
Single Strand, WQT = Quad-Twist™, WDT = Duo-Twist™, WDL = Duo-Lead, WQL = Quad-Lead™, WMW =
Manganin, and WHD = Heavy Duty. See the Lake Shore Catalog for details.
Apiezon ® "N" Grease, 25 gram Tube. General purpose grease well-suited for cryogenic use because of its
low viscosity. Often used to thermally anchor cryogenic sensors as well as lubricate joints and o-rings. Contains
GAN-25
high molecular weight polymeric hydrocarbon additive which gives it a tenacious, rubbery consistency that
forms a cushion between mating surfaces.
Indium Foil (5 Pieces). Indium is a semi-precious non-ferrous metal, softer than lead, and extremely malleable
IF-5
and ductile. It stays soft and workable down to cryogenic temperatures. May be used as a sealing gasket for
covers, flanges, and windows in cryogenic applications.
25 Ω Ω Ω Ω Cartridge Heater. Features precision-wound nickel-chromium resistance wire, magnesium oxide
insulation, two solid pins, non-magnetic package, and has UL and CSA component recognition. The heater is
HTR-25
25 W, 6.35 mm (0.25 inch) diameter by 25.4 mm (1 inch) long. The 25 W rating is in dead air. In cryogenic
applications, the cartridge heater can handle many times this dead air power rating.
50 Ω Ω Ω Ω Cartridge Heater. Features precision-wound nickel-chromium resistance wire, magnesium oxide
insulation, two solid pins, non-magnetic package, and has UL and CSA component recognition. The heater is
HTR-50
25 W, 6.35 mm (0.25 inch) diameter by 25.4 mm (1 inch) long. The 25 W rating is in dead air. In cryogenic
applications, the cartridge heater can handle many times this dead air power rating.
119-009 * Model 330 User's Manual.
* Accessories included with a new Model 330.
Options and Accessories
DESCRIPTION OF MODEL 330 ACCESSORY
6-3