Ieee-488/Serial Interface Command Summary; Command List Structure - Lakeshore 330 User Manual

Lake Shore Model 330 Autotuning Temperature Controller User's Manual
4.3

IEEE-488/SERIAL INTERFACE COMMAND SUMMARY

The IEEE-488/Serial Interface commands are listed alphabetically in function order. There are five command
groups: Common Commands (Paragraph 4.3.2), Interface Commands (Paragraph 4.3.3), Display Commands
(Paragraph 4.3.4), Control Process Commands (Paragraph 4.3.5), and Curve Commands (Paragraph 4.3.6).
The commands are listed in the same order as shown below.
Command Function
Common Commands
*CLS Clear Interface .................................... 4-11
*ESE Set Std. Event Status Enable ............. 4-11
*ESE? Query Std. Event Status Enable ......... 4-11
*ESR? Query Std. Event Status Register....... 4-11
*IDN? Query Identification............................. 4-11
*OPC Set Operation Complete ..................... 4-11
*OPC? Query Operation Complete................. 4-11
*RST Reset Instrument ................................ 4-12
*SRE Set Service Request Enable............... 4-12
*SRE? Query Service Request Enable .......... 4-12
*STB? Query Status Byte............................... 4-12
*TST? Query Self-Test................................... 4-12
*WAI Wait-To-Continue ............................... 4-12
Interface Commands
ADDR Set Address ........................................ 4-13
ADDR? Address Query.................................... 4-13
END EOI ..................................................... 4-13
END? EOI Query........................................... 4-13
MODE Remote Mode ..................................... 4-13
MODE? Remote Mode Query .......................... 4-13
TERM Terminator .......................................... 4-13
TERM? Terminator Query................................ 4-14
Display Commands
CCHN Set Control Channel ........................... 4-14
CCHN? Control Channel Query ....................... 4-14
CDAT? Control Sensor Data Query ................ 4-14
CUNI Set Control Units ................................ 4-14
CUNI? Control Units Query ............................ 4-14
FILT Set Display Filter ................................ 4-15
FILT? Display Filter Query ............................ 4-15
SCHN Set Sample Channel........................... 4-15
SCHN? Sample Channel Query ...................... 4-15
SDAT? Sample Sensor Data Query................ 4-15
SUNI Set Sample Units................................ 4-15
SUNI? Sample Units Query............................ 4-15
4.3.1

Command List Structure

Syntax of what user must input
Information returned in response
Explanation and definition of
4-10
Page
Command Name
CUNI?
Input:
Returned:
Remarks:
to the query
returned data
Command Function
Control Process Commands
CLIM Control Limit ......................................4-16
CLIM? Control Limit Query............................4-16
GAIN Set Gain ............................................4-16
GAIN? Gain Query ........................................4-16
HEAT? Heater Query .....................................4-16
RAMP Enable/Disable Ramping...................4-16
RAMP? Ramping Enable/Disable Query ........4-16
RAMPR Set Ramp Rate in K/min. ...................4-17
RAMPR? Ramp Rate Query..............................4-17
RAMPS? Ramping Status Query ......................4-17
RANG Set Range .........................................4-17
RANG? Range Query .....................................4-17
RATE Set Rate ............................................4-17
RATE? Rate Query ........................................4-17
RSET Set Reset...........................................4-17
RSET? Reset Query ......................................4-17
SETP Set Setpoint.......................................4-18
SETP? Setpoint Query...................................4-18
TUNE Tune Status .......................................4-18
TUNE? Tune Query........................................4-18
ZONE Store Zone.........................................4-18
ZONE? Zone Query........................................4-18
Curve Commands
ACOMP Set A Compensation .........................4-19
ACOMP? A Compensation Query .....................4-19
ACUR Set Curve for A ..................................4-19
ACUR? Curve A Query...................................4-19
ATYPE? A Input Type Query ...........................4-19
BCOMP Set B Compensation .........................4-19
BCOMP? B Compensation Query .....................4-19
BCUR Set Curve for B ..................................4-19
BCUR? Curve B Query...................................4-20
BTYPE? B Input Type Query ...........................4-20
CUID? Curve Identification Query .................4-20
CURV Curve Set...........................................4-20
CURV? Curve No. Information Query.............4-21
ECUR Edit Curve..........................................4-22
FREE? Curve Bytes Free Query....................4-22
KCUR Delete Curve......................................4-22
SCAL SoftCal Entry .....................................4-22
Brief Description of Function
Control Units Query
CUNI?
K, C, V, R, or M
Used to query the unit for current control units
information. The character returned will be K for
kelvin, C for Celsius, V for Volts, R for Ohms, or
M for millivolts.
Page
Remote Operation