Denon AVR-2113 Owner's Manual page 148

GAudioH
Symptom
Audio is not output. • Check the connections for all devices.
• Check the speaker connections and configurations.
• Check whether the audio device power is turned on.
• Adjust the master volume.
• Cancel the mute mode.
• Check the connection with the playback device and select the
proper input source.
• Match the input mode and the terminal assigned to be the digital
input terminal.
• Disconnect the headphones. No sound is output from the
speakers when headphones are connected.
The volume does not • The maximum volume is set too low. Set the maximum volume
increase. using "Limit"on the menu.
• Power for external devices connected to the output connectors
of the unit may not be turned on. Check the power of connected
external devices.
No sound is • Check if the surround speakers are connected to the SURROUND
produced from terminals.
surround speaker.
No sound is • Check if "Assign Mode" is set appropriately in order to output
produced from audio from the surround back speakers.
surround back • Set "Speaker Config." – "Surr. Back" on the menu to something
speaker. other than "None".
• Set the sound mode to something other than "STEREO" and
"VIRTUAL".
No sound is • Check if "Assign Mode" is set appropriately in order to output
produced from front audio from the front height speakers.
height speaker. • Set "Speaker Config." – "Front Height" on the menu to something
other than "None".
DVD
Cause/Solution
9,
15,
19, 20, 21
78,
82, 83, 84
Symptom
Page
No sound is • Check the subwoofer connections.
1 0, 1 3, 1 6, produced from
subwoofer. • Turn on the subwoofer's power.
1 4, 1 7, 1 8,
• Set "Speaker Config." – "Subwoofer" on the menu to "Yes".
• If "Front" and "Center" for "Speaker Config." are set to "Large",
and "Subwoofer Mode" is set to "LFE", no sound may be output
7 9, 8 0, 8 1,
from the subwoofers, depending on the input signal or selected
sound mode.
–
DTS sound is not • Set "Decode Mode" on the menu to "Auto" or "DTS".
31, 92
output.
31, 92
Dolby TrueHD, DTS- • Make HDMI connections.
30, 92
HD, Dolby Digital
Plus audio is not
113
output.
• Check that "Speaker Config." – "Center" or "Surround" is set to
Dolby PLg mode or
129
other than "None". If the speaker system is 2.0/2.1ch, this sound
DTS NEO:6 mode
mode cannot be selected.
cannot be selected.
103
• When headphones are used, Dolby PLg or DTS NEO:6 cannot be
selected.
–
Audyssey MultEQ ®
• Switch the sound mode to other than "DIRECT" or "PURE
XT, Audyssey DIRECT".
Dynamic EQ ® and • When headphones are used, Audyssey MultEQ ® XT, Audyssey
–
Dynamic EQ ® and Audyssey Dynamic Volume ® cannot be
Audyssey Dynamic
Volume ® cannot be
selected.
selected.
115
• Run Audyssey ® Setup.
Audyssey Dynamic
EQ ® and Audyssey
115
Dynamic Volume ®
cannot be selected.
68
"Restorer" cannot • Check that an analog signal or PCM signal (Sample Rate=44.1/48
be selected. kHz) is input. For playback of multichannel signals such as Dolby
115
Digital or DTS surround, "Restorer" cannot be used.
• Switch the sound mode to other than "DIRECT" or "PURE
116
DIRECT".
145
Cause/Solution
78,
82, 83, 84
Page
7 9, 8 0, 8 1,
–
115
115, 116
113
10
115
–
68
–
23, 85
102
68