Denon AVR-2113 Owner's Manual page 120

Setting items
Levels Test Tone Start : Output test tone.
Set the volume of the test • Front L / F. Height L / Center / F. Height R / Front R / Surround R /
tone to be the same when it
Surr. Back R
is output from each speaker. speaker to output test tone.
z When the "Speaker Config." – "Surr. Back" setting (vpage 115) is
set to "1spkr", "Surr. Back" is displayed.
• –12.0dB – +12.0dB (0.0dB) : Adjust the volume.
When "Levels" is adjusted, the adjusted values are set for all the sound
modes.
NOTE
• Speakers set to "None" in the "Speaker Config."
settings are not displayed.
• When a headphones jack is inserted in the PHONES jack of this unit, the
"Levels" is not displayed.
Set Defaults : The "Levels" settings are returned to the default settings.
• Yes : Reset to the defaults.
• No : Do not reset to the defaults.
When you select "Set Defaults" and press
ENTER
, the "Reset to the default values?"
prompt is displayed. Select either "Yes" or
"No", and press
DVD
Setting details
z z
/ Surr. Back L / Surround L / Subwoofer : Select
(vpage
ENTER
.
Setting items
Crossovers Crossover : Set the crossover frequency.
Set the maximum frequency • 40Hz / 60Hz / 80Hz / 90Hz / 100Hz / 110Hz / 120Hz / 150Hz / 200Hz /
of the bass signal output 250Hz / Individual : Set the crossover frequency for all speakers. See
from each channel to the speaker manual for information concerning speaker crossover
the subwoofer. Set the frequency.
Crossover Frequency to
The following settings can be set when the "Crossover" setting is set to
suit the bass reproduction
"Individual".
capability of the speaker
• Front / Center / Surround / Surr. Back / Front Height : Select speaker
being used.
for setting of crossover frequency.
• 40Hz / 60Hz / 80Hz / 90Hz / 100Hz / 110Hz / 120Hz / 150Hz / 200Hz /
250Hz : Set the crossover frequency.
115) • "Crossovers" can be set when the "Bass" – "Subwoofer Mode"
(vpage 116) setting is "LFE+Main", or when you have a speaker that
is set to "Small".
• Always set the crossover frequency to "80Hz". When using small
speakers, however, we recommend setting the crossover frequency to
a higher frequency.
• For speakers set to "Small", sound below the crossover frequency
is cut from the sound output. The cut bass sound is output from the
subwoofer or front speakers.
• The speakers that can be set when "Individual" is selected differ
depending on to the "Subwoofer Mode" setting (vpage 116).
• When "LFE" is selected, speakers set to "Small" at "Speaker Config."
can be set. If the speakers are set to "Large", "Full Band" is displayed
and the setting cannot be made.
• If set to "LFE+Main", this setting can be made regardless of the
speaker size.
Front Speaker Setup 2ch Playback : The front speakers used in direct play (2 channel), stereo
Set the front speakers to play and pure direct play (2 channel) are set in advance.
use for every sound mode. • A : Front speaker A is used.
• B : Front speaker B is used.
NOTE
• A+B : Both front speakers A and B are used.
This can be set when
Multi ch Playback : The front speakers used in play modes other than
"Assign Mode" is set to
direct play (2 channel), stereo play and pure direct play (2 channel) are set
"Front B" (vpage 115).
in advance.
• A : Front speaker A is used.
• B : Front speaker B is used.
• A+B : Both front speakers A and B are used.
117
Speakers
Setting details