Download Table of Contents Print this page
Panasonic Pure IP-PBX KX-TDE600 Installation Manual

Panasonic Pure IP-PBX KX-TDE600 Installation Manual

Pure ip-pbx
Hide thumbs Also See for Pure IP-PBX KX-TDE600:

Advertisement

Table of Contents
Thank you for purchasing a Panasonic Pure IP-PBX.
Please read this manual carefully before using this product and save this manual for future use.
KX-TDE600: PGMPR Software File Version 3.0000 or later

Installation Manual

Pure IP-PBX
KX-TDE600
Model No.
Document Version: 2009-12
SD Logo is
a trademark.

Advertisement

Table of Contents
loading

Related Manuals for Panasonic Pure IP-PBX KX-TDE600

Summary of Contents for Panasonic Pure IP-PBX KX-TDE600

  • Page 1: Installation Manual

    Pure IP-PBX KX-TDE600 Model No. Thank you for purchasing a Panasonic Pure IP-PBX. Please read this manual carefully before using this product and save this manual for future use. SD Logo is KX-TDE600: PGMPR Software File Version 3.0000 or later a trademark.
  • Page 2: System Components

    System Components System Components System Components Table Category Model No. Description Basic Shelf KX-TDE600 Basic Shelf Main Processing Card Main Processing Card (IPCEMPR) IPCEMPR Optional Cards KX-TDE0105 Memory Expansion Card (IPCMEC) KX-TDE0110 16-Channel VoIP DSP Card (DSP16) KX-TDE0111 64-Channel VoIP DSP Card (DSP64) KX-TDA0196 Remote Card (RMT) Optional Shelf Expansion...
  • Page 3 System Components Category Model No. Description KX-NCS4704 4-Channel SIP Extension Activation Key (4 SIP Extension) KX-NCS4708 8-Channel SIP Extension Activation Key (8 SIP Extension) KX-NCS4716 16-Channel SIP Extension Activation Key (16 SIP Extension) KX-NCS4950 Activation Key for Software Upgrade to Enhanced Version (Software Upgrade 01) KX-NCS2101 Activation Key for CA Basic for 1 User (CA Basic 1user)
  • Page 4 System Components Category Model No. Description KX-TDA0170 8-Port Digital Hybrid Extension Card (DHLC8) KX-TDA0171 8-Port Digital Extension Card (DLC8) KX-TDA0172 16-Port Digital Extension Card (DLC16) KX-TDA0173 8-Port Single Line Telephone Extension Card (SLC8) KX-TDA0177 16-Port Single Line Telephone Extension Card with Caller ID (CSLC16) KX-TDA0470 16-Channel VoIP Extension Card (IP-EXT16)
  • Page 5 Activation Key for Software Upgrade to Enhanced Version (Software Upgrade 01) KX-TDA0108 S-Type Power Supply Unit (PSU-S) Equipment Compatibility Compatible Panasonic Proprietary Telephones The PBX supports the following telephones: • IP proprietary telephones (e.g., KX-NT300 series) • IP softphones (e.g., KX-TDA0350) •...
  • Page 6: Safety Notices

    System Components • Single line telephones Incompatible Panasonic Proprietary Telephones The PBX does not support the following telephones: • KX-T30800 series proprietary telephones and DSS consoles • KX-T61600 series proprietary telephones and DSS consoles • KX-T123200 series proprietary telephones and DSS consoles Note •...
  • Page 7: Important Safety Instructions

    Important Safety Instructions Important Safety Instructions When using your telephone equipment, basic safety precautions should always be followed to reduce the risk of fire, electric shock and injury to persons, including the following: • Do not use the product near water, for example, near a bathtub, wash bowl, kitchen sink, or laundry tub, in a wet basement, or near a swimming pool.
  • Page 8: Important Information

    Important Information Important Information SAVE THESE INSTRUCTIONS WARNING SAFETY REQUIREMENTS For All Telephone Equipment • Do not install the product in any other way than described in relevant manuals. • The product must only be installed and serviced by qualified service personnel. The product should be used as-is from the time of purchase;...
  • Page 9 Unplug all installed shelves of the system from the AC outlet if it emits smoke, an abnormal smell or makes unusual noise. These conditions can cause fire or electric shock. Confirm that smoke has stopped and contact an authorized Panasonic Factory Service Center. •...
  • Page 10 Contact your telephone company. If all SLTs operate properly, there may be a problem with your PBX. Do not reconnect the PBX to the CO lines until it has been serviced by an authorized Panasonic Factory Service Center. Installation Manual...
  • Page 11 Precaution Precaution WARNING REMOVE MEMORY CARD WHILE POWER SUPPLIED TO THE PBX Doing so may cause the PBX to fail to start when you try to restart the system. Document Version 2009-12 Installation Manual...
  • Page 12 Precaution Password Security CAUTION To the Administrator or Installer regarding the system password Please provide all system passwords to the customer. To avoid unauthorized access and possible abuse of the PBX, keep the passwords secret, and inform the customer of the importance of the passwords, and the possible dangers if they become known to others.
  • Page 13: Installation Manual

    Introduction Introduction This Installation Manual is designed to serve as an overall technical reference for the Panasonic Pure IP-PBX, KX-TDE600. It provides instructions for installing the hardware, and programming the PBX using the Maintenance Console. The Structure of this Manual...
  • Page 14 Installation must be performed by a qualified professional installer. If required, provide the telephone company with the following technical information: • Telephone numbers to which the system will be connected • Make: Panasonic • Model: KX-TDE600 • Certification No.: found on the side of the unit •...
  • Page 15 F.C.C. REQUIREMENTS AND RELEVANT INFORMATION interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
  • Page 16: Table Of Contents

    Table of Contents Table of Contents 1 System Outline ..................19 System Construction ......................20 1.1.1 Basic System ........................20 1.1.2 Expanded System ......................21 1.1.3 System Connection Diagram ..................26 Optional Equipment ......................28 1.2.1 Optional Equipment ......................28 Specifications ........................31 1.3.1 General Description ......................31 1.3.2 Characteristics ........................33 1.3.3 System Capacity ......................34...
  • Page 17 Table of Contents 3.7.2 CID8 Card (KX-TDA0193) ....................142 3.7.3 T1 Card (KX-TDA0187) ....................143 3.7.4 PRI23 Card (KX-TDA0290) ..................145 3.7.5 IP-GW4E Card (KX-TDA0484) ..................147 3.7.6 IP-GW16 Card (KX-TDA0490) ..................149 Information about the Extension Cards ..............151 3.8.1 CSIF4 Card (KX-TDA0143) and CSIF8 Card (KX-TDA0144) ........151 3.8.2 DHLC8 Card (KX-TDA0170) ..................153 3.8.3...
  • Page 18 Table of Contents 6 Appendix ....................221 Revision History ......................222 6.1.1 PGMPR Software File Version 3.0xxx ................222 Index......................223 Installation Manual Document Version 2009-12...
  • Page 19: System Outline

    Section 1 System Outline This section provides general information on the PBX, including the system capacity and specifications. Document Version 2009-12 Installation Manual...
  • Page 20: System Construction

    1.1.1 Basic System 1.1 System Construction 1.1.1 Basic System Basic Shelf The Basic Shelf contains an IPCEMPR card for controlling the PBX. To use the basic system, install a power supply unit (PSU) in the PSU Slot and optional service cards in Free Slots. To expand to a multiple-shelf system, you also need to install a BUS-M card in the BUS-M Card Slot.
  • Page 21: Expanded System

    1.1.2 Expanded System 1.1.2 Expanded System Expansion Shelf Each Expansion Shelf contains a BUS-S card for connecting to the Basic Shelf. To use Expansion Shelf, connect it to the Basic Shelf, and install a power supply unit (PSU) in the PSU Slot and optional service cards in Free Slots.
  • Page 22 1.1.2 Expanded System 2-shelf System Expanded system (Basic Shelf + 1 Expansion Shelf). Expansion Shelf 1 is mounted on the Basic Shelf. CAUTION If you are installing a 2-shelf system in an area prone to earthquakes, make sure to fix the system to the wall using the wall brackets (supplied with an optional Mounting Kit).
  • Page 23 1.1.2 Expanded System 3-shelf System (Tower Type) Expanded system (Basic Shelf + 2 Expansion Shelves). Expansion Shelves 1 and 2 are mounted on the Basic Shelf. A Mounting Kit is required for the 3-shelf system. Document Version 2009-12 Installation Manual...
  • Page 24 1.1.2 Expanded System 4-shelf System (Tower Type) Fully expanded system (Basic Shelf + 3 Expansion Shelves). Expansion Shelves 1 to 3 are mounted on the Basic Shelf. A Mounting Kit is required for the 4-shelf system. Installation Manual Document Version 2009-12...
  • Page 25 1.1.2 Expanded System 4-shelf System (Side-by-side Type) When vertical space is limited, it is possible to install a fully expanded system (Basic Shelf + Expansion Shelf 1, and Expansion Shelf 2 + Expansion Shelf 3 ) in a side-by-side configuration. Expansion Shelf 1 is mounted on the Basic Shelf, and Expansion Shelf 3 is mounted on Expansion Shelf 2.
  • Page 26: System Connection Diagram

    1.1.3 System Connection Diagram 1.1.3 System Connection Diagram ITSP Private Network IP Network CO (Telephone Company) Lines Analog/PRI/T1 Remote PC Router (e.g., ADSL Modem) IP-PT IP Softphone, CA Client PC Fax Machine SIP Extension Printer DSS Console IP-CS Wireless Phone External Sensor/ External Relay Device DSS Console...
  • Page 27 1.1.3 System Connection Diagram ECSLC24 (KX-TDA6178) ELCOT16 (KX-TDA6181) EMSLC16 (KX-TDA6175) Analog Analog Analog CID8 CO Line CO Line CO Line (KX-TDA0193) ESLC16 Telephone (KX-TDA6174) Company ISDN PRI Line ISDN PRI Line ISDN PRI Line CSLC16 Wireless Phone Fax Machine (Digital CO Line) (Digital CO Line) (Digital CO Line) (KX-TDA0177)
  • Page 28: Optional Equipment

    1.2.1 Optional Equipment 1.2 Optional Equipment 1.2.1 Optional Equipment Model No. Model Name Description KX-TDE0105 Memory Expansion Card Memory expansion card to increase system data (IPCMEC) storage space. To be mounted on the IPCEMPR card. KX-TDE0110 16-Channel VoIP DSP Card 16-channel digital signal processor card with a (DSP16) 4-Channel IP Trunk activation key and a...
  • Page 29 NI (North American standard ISDN protocol) compliant. KX-TDA0470 16-Channel VoIP Extension Card 16-channel VoIP extension card. Compliant with (IP-EXT16) Panasonic proprietary protocol, and ITU-T G. 729A and G.711 codec methods. KX-TDA0484 4-Channel VoIP Gateway Card 4-channel VoIP gateway card. Compliant with (IP-GW4E) VoIP H.323 V.2 protocol, and ITU-T G.729A, G.
  • Page 30 1.2.1 Optional Equipment Model No. Model Name Description KX-TDA6175 16-Port Single Line Telephone 16-port extension card for SLTs with Message Extension with Message Lamp Waiting Lamp control and 4 power failure transfer Card (EMSLC16) (PFT) ports. Maximum power output of 145 V/ 85 V for Message Waiting Lamp control.
  • Page 31: Specifications

    1.3.1 General Description 1.3 Specifications 1.3.1 General Description Control Bus Original bus (16-bit, 8 MHz, 10 megabytes per second) Communication Bus H.100 bus conformity (1024 time slots) Switching Distributed Switching Power Input PSU-M 100 V AC to 130 V AC; 2.5 A/200 V AC to 240 V AC; 1.4 A; 50 Hz/60 Hz PSU-L 100 V AC to 130 V AC;...
  • Page 32 1.3.1 General Description PT-interface CS 1-pair wire (D1, D2) PT-interface CS (High-density) 4-pair wire (D1, D2) DSS Console and Add-on Key 1-pair wire (D1, D2) Module 430 mm (W) ´ 415 mm (H) ´ 270 mm (D) Dimension Basic Shelf (17-1/5 in ´...
  • Page 33: Characteristics

    1.3.2 Characteristics 1.3.2 Characteristics Terminal Equipment Loop Limit • PT: KX-DT300/KX-T7600 series DPT: 90 W; all other DPTs/APTs: 40 W SLT: 600 W including set • • Doorphone: 20 W CS: 130 W; PT-interface CS: 65 W • 15 000 W minimum Minimum Leakage Resistance Maximum Number of Extension for PT or SLT...
  • Page 34: System Capacity

    1.3.3 System Capacity 1.3.3 System Capacity Type and Maximum Number of Slots The PBX supports the following type and number of slots. Maximum Number Slot Type 2-shelf 3-shelf 4-shelf Basic System System System System IPCEMPR Card Slot BUS-M Card Slot Free Slot Virtual CO Line Slot Virtual Slot...
  • Page 35 1.3.3 System Capacity Virtual Slots of the IPCEMPR Card Virtual CO Virtual Line Slots Extension Slots IPCEMPR Card Virtual Slots Maximum Optional Service Cards The following number of cards can be installed in the Free Slots or Virtual Slots of the PBX. Note •...
  • Page 36 1.3.3 System Capacity Cards Installed in Free Slots or Virtual Slots Maximum Number 3-shelf 2-shelf 4-shelf Basic Card Type System System System System IPCEMPR CO Line Card Virtual CO Line Card V-IPGW16 V-SIPGW16 Physical CO Line Card ELCOT16 PRI23 IP-GW4E IP-GW16 Extension Card Virtual Extension Card...
  • Page 37 1.3.3 System Capacity Cards Mounted on Other Optional Service Cards Maximum Number Card Type Mounted on 2-shelf 3-shelf 4-shelf Basic System System System System DSP16 DSP64 IPCEMPR Card IPCMEC CID8 ELCOT16 Card EXT-CID SLC8 Card DPH4 MSG4 OPB3 Card ESVM4 EIO4 BUS-ME –...
  • Page 38 1.3.3 System Capacity Maximum CO Lines and Extensions The PBX supports the following number of CO lines and extensions. Basic 2-shelf 3-shelf 4-shelf Type System System System System Total Number of CO Lines CO Line (Physical CO Line Card) CO Line (Virtual CO Line Card) H.323 CO Lines SIP CO Lines Total Number of Extensions...
  • Page 39 1.3.3 System Capacity Maximum Terminal Equipment The following number of items of terminal equipment can be supported by the PBX. 2-shelf 3-shelf 4-shelf Terminal Equipment Type Basic System System System System Telephone (using Digital XDP) (432) (736) (1008) (1152) KX-DT300/KX-T7600 series DPT Other DPT IP-PT IP-PT...
  • Page 40 1.3.3 System Capacity Note for KX-NT265 IP-PT users The supported card varies depending on the software version of your KX-NT265 IP-PT. To confirm the version, follow the procedure below: While starting up SP-PHONE SP-PHONE PROGRAM "AP Version". Select Select "Maintenance". "Version display".
  • Page 41 1.3.3 System Capacity PSU Capacity Each PSU supports a different load figure. PSU Type Maximum Load Figure PSU-M PSU-L If the total load figure is greater than 128, you must install the PSU-L. If the total load figure is less than 128, but you expect expansion in the future, it may be better to install the PSU-L instead of the PSU-M.
  • Page 42 1.3.3 System Capacity Installation Manual Document Version 2009-12...
  • Page 43: Activation Key Installation

    Section 2 Activation Key Installation This section describes information on activation keys, including how to obtain an activation key and install it in the SD Memory Card. Document Version 2009-12 Installation Manual...
  • Page 44: Information About The Activation Keys

    2.1.1 Activation Keys 2.1 Information about the Activation Keys 2.1.1 Activation Keys To use IP CO lines and IP telephones on a private IP network using the IPCEMPR card or to upgrade the software for enhanced features, you need the appropriate activation keys. Type and Maximum Number of Activation Keys The PBX supports the following type and number of activation keys: Supported IP CO lines/...
  • Page 45 2.1.1 Activation Keys Supported IP CO lines/ Maximum Activation Key Type Description IP Telephones/CA Number Users Allows the use of CA Basic for 128 CA Basic 128users 128 users users. Allows the use of CA PRO for 1 CA Pro 1user 128 users user.
  • Page 46 2.1.1 Activation Keys Activation Keys for IP CO Lines Maximum Number/Supported IP CO Lines Model No. Activation Key Type with DSP16 with DSP64 KX-NCS4102 2 IP Trunk 60 IP CO lines 48 IP CO lines (H. (H.323/SIP) 323/SIP) KX-NCS4104 4 IP Trunk Activation Keys for IP Telephones Maximum Number/Supported IP Telephones Model No.
  • Page 47 2.1.1 Activation Keys Model No. Activation Key Type Maximum Number Supported CA Users KX-NCS2205 CA Pro 5users 125 users KX-NCS2210 CA Pro 10users 120 users KX-NCS2240 CA Pro 40users 120 users KX-NCS2249 CA Pro 128users 128 users KX-NCS2301 CA Supervisor 1user 4 users Activation Keys for Software Upgrading Model No.
  • Page 48: Activation Key Code And Key Management System

    2.1.2 Activation Key Code and Key Management System 2.1.2 Activation Key Code and Key Management System To obtain additional activation keys, you need to purchase the appropriate activation key codes and access the Key Management System. You can download the activation keys as an activation key file from the Key Management System.
  • Page 49: Activation Key File

    2.1.3 Activation Key File 2.1.3 Activation Key File The corresponding number of IP CO lines and IP telephones or enhanced features can be activated by installing the downloaded activation key file(s) in the SD Memory Card of the IPCEMPR card using the Maintenance Console.
  • Page 50 2.1.3 Activation Key File Installation Manual Document Version 2009-12...
  • Page 51: Installation

    Section 3 Installation This section describes the procedures to install the PBX. Detailed instructions for planning the installation site, installing the shelves and optional service cards, and cabling of peripheral equipment are provided. Further information on system expansion and peripheral equipment installation is included.
  • Page 52: Before Installation

    3.1.1 Before Installation 3.1 Before Installation 3.1.1 Before Installation Please read the following notes concerning installation and connection before installing the PBX and terminal equipment. Be sure to comply with all applicable laws, regulations, and guidelines. Safety Installation Instructions WARNING When installing telephone wiring, basic safety precautions should always be followed to reduce the risk of fire, electric shock and injury to persons, including the following: •...
  • Page 53 3.1.1 Before Installation • Do not stack up the optional service cards. Wiring Precautions Be sure to follow these instructions when wiring the unit: WARNING • Do not run unshielded telephone cables near AC power cables, computer cables, AC power sources, etc.
  • Page 54: Installation Of The Pbx

    3.2.1 Unpacking 3.2 Installation of the PBX 3.2.1 Unpacking Supplied Items for the Basic Shelf (KX-TDE600) Unpack the box and check the items below: Main Unit Ferrite Core (for the IPCEMPR card) Metal Bracket Anchor Plug Fan Guard Mini Plug (for pager and music source) SD Memory Card Screw A Screw B...
  • Page 55 3.2.1 Unpacking Supplied Items for an Expansion Shelf (KX-TDE620) Unpack the box and check the items below: Main Unit Metal Bracket Anchor Plug Fan Guard Screw A Screw B Screw C Supplied Items for the Mounting Kit (KX-TDA6201) Unpack the box and check the items below: Wall Bracket (Right) Wall Bracket (Left) Base Stand...
  • Page 56: Names And Locations

    3.2.2 Names and Locations 3.2.2 Names and Locations Inside View Basic Shelf (KX-TDE600) Expansion Shelf (KX-TDE620) RUN Indicator ALARM Indicator MNT Port LAN Port PSU Slot Free Slots 1 to 10 (from the left) IPCEMPR Card BUS-M Card Slot RS-232C Port Free Slots 1 to 11 (from the left) BUS-S Card Installation Manual...
  • Page 57: Opening/Closing The

    3.2.3 Opening/Closing the Front Cover 3.2.3 Opening/Closing the Front Cover Opening the Front Cover Insert a flathead screwdriver into the opening (on the left of the screw cover) and unlatch the screw cover. Screw Cover Turn the screw counterclockwise to loosen. Slide the front cover to the right until it stops, then lift the front cover.
  • Page 58: Closing The Front Cover

    3.2.3 Opening/Closing the Front Cover Closing the Front Cover Hook the front cover onto the shelf (line up the protrusions on the cover with the receptacles on the shelf). Then slide the front cover to the left until it locks. Turn the screw clockwise to tighten.
  • Page 59: Attaching Fan Guards

    3.2.4 Attaching Fan Guards 3.2.4 Attaching Fan Guards Attaching Fan Guards Fan Guards (supplied with the shelf) must be attached using the screws (C) when: • installing a multiple-shelf system, • mounting the shelf on the wall, or • installing the shelf near the wall to protect the air vents on the back of the shelf.
  • Page 60: Installation Of Basic System Or 2-Shelf System (Floor Standing)

    3.2.5 Installation of Basic System or 2-shelf System (Floor Standing) 3.2.5 Installation of Basic System or 2-shelf System (Floor Standing) The PBX can be expanded to a 2-shelf system by mounting an Expansion Shelf on the Basic Shelf. Construction of Basic System or 2-shelf System Expansion Shelf 1 Metal Bracket 2-shelf...
  • Page 61: Metal Bracket

    3.2.5 Installation of Basic System or 2-shelf System (Floor Standing) Installing the Basic Shelf For the basic system, install the metal bracket (supplied with the Basic Shelf) on the floor first. Then, attach the Basic Shelf to the metal bracket. Install 4 anchor plugs on the floor, using the metal bracket as a template.
  • Page 62 3.2.5 Installation of Basic System or 2-shelf System (Floor Standing) Secure the Basic Shelf to the metal bracket with 2 screws (B). Screw (B) Installation of the basic system is complete. If you are installing a 2-shelf system, follow the procedure below. Mounting Expansion Shelf 1 For the 2-shelf system, attach the metal bracket (supplied with the Expansion Shelf 1) to the Basic Shelf first.
  • Page 63 3.2.5 Installation of Basic System or 2-shelf System (Floor Standing) Fix the metal bracket to the Basic Shelf with 4 screws (B). Metal Bracket Screw (B) Lift Expansion Shelf 1, attach it to the metal bracket on the Basic Shelf, and slide it backwards until it locks. Metal Bracket Document Version 2009-12 Installation Manual...
  • Page 64: Screw C

    3.2.5 Installation of Basic System or 2-shelf System (Floor Standing) Secure Expansion Shelf 1 to the metal bracket with 2 screws (B). Screw (B) Shelf installation is complete. Next, it is necessary to connect the shelves. Installation Manual Document Version 2009-12...
  • Page 65 3.2.5 Installation of Basic System or 2-shelf System (Floor Standing) Connecting Shelves For the 2-shelf system, you need to install an optional BUS-M card in the Basic Shelf. To connect the shelves, plug the Bus Cable (supplied with the BUS-M card) into the bottom slot of the BUS-M card. Then, plug the other end into the BUS-S card built in to Expansion Shelf 1.
  • Page 66 3.2.5 Installation of Basic System or 2-shelf System (Floor Standing) Turn the 2 screws clockwise to fix the BUS-M card in place. Screws Plug the Bus Cable into the bottom port of the BUS-M card in the Basic Shelf. Then, plug the other end into the BUS-S card in Expansion Shelf 1.
  • Page 67 3.2.5 Installation of Basic System or 2-shelf System (Floor Standing) Attach the noise shield wires of the Bus Cable to the Basic Shelf and Expansion Shelf 1 with the screws of the BUS-M card. Note When attaching or removing the noise shield wires, make sure that the DC power supply is turned off. Screw Noise Shield Wire Document Version 2009-12...
  • Page 68: Installation Of 3- Or 4-Shelf System (Tower Type)

    3.2.6 Installation of 3- or 4-shelf System (Tower Type) 3.2.6 Installation of 3- or 4-shelf System (Tower Type) The PBX can be expanded to a 3- or 4-shelf system by mounting Expansion Shelves on the Basic Shelf. For a 3- or 4-shelf system, you need a Mounting Kit, which supplies you with the base stands and wall brackets. Construction of 3- or 4-shelf System (Tower Type) Wall Bracket (Left)
  • Page 69 3.2.6 Installation of 3- or 4-shelf System (Tower Type) WARNING Be careful not to drop any components. Dropping components may damage them or cause an injury. CAUTION • Do not block the openings of the shelf. Allow space of at least 10 cm (4 in) at the sides of the shelf, and 20 cm (8 in) above the top-mounted shelf.
  • Page 70 3.2.6 Installation of 3- or 4-shelf System (Tower Type) Note If necessary, it is possible to reverse the direction of the base stands as shown below: Place the metal bracket on the base stands. Metal Bracket Installation Manual Document Version 2009-12...
  • Page 71 3.2.6 Installation of 3- or 4-shelf System (Tower Type) Attach the metal bracket to the base stands with 4 screws (B). Screw (B) Make 4 holes for anchor plugs on the floor, using the measurements indicated here. W a l l 95 mm (3-3/4 in) 510 mm...
  • Page 72 3.2.6 Installation of 3- or 4-shelf System (Tower Type) Install 4 anchor plugs in the holes on the floor. Then, fasten the base stands to the floor loosely with 4 screws (A). (This makes it easy to adjust the position of the shelves later.) Screw (A) Washer...
  • Page 73 3.2.6 Installation of 3- or 4-shelf System (Tower Type) Lift the Basic Shelf, attach it to the metal bracket, and slide it backwards until it locks. Metal Bracket Secure the Basic Shelf to the metal bracket with 2 screws (B). Screw (B) Document Version 2009-12 Installation Manual...
  • Page 74 3.2.6 Installation of 3- or 4-shelf System (Tower Type) Mounting Expansion Shelves 1 and 2 For the 3- or 4-shelf system, attach the metal bracket (supplied with the Expansion Shelf) to the Basic Shelf first. After mounting Expansion Shelf 1 on the Basic Shelf, fix Expansion Shelf 1 to the wall. Then, mount Expansion Shelf 2 on Expansion Shelf 1.
  • Page 75 3.2.6 Installation of 3- or 4-shelf System (Tower Type) Lift Expansion Shelf 1, attach it to the metal bracket on the Basic Shelf, and slide it backwards until it locks. Metal Bracket Secure Expansion Shelf 1 to the metal bracket with 2 screws (B). Screw (B) Document Version 2009-12 Installation Manual...
  • Page 76 3.2.6 Installation of 3- or 4-shelf System (Tower Type) Fixing to the Wall Attach the metal bracket to the wall brackets. Metal Bracket Wall Bracket (Left) Wall Bracket (Right) Fix the metal bracket to Expansion Shelf 1 with 4 screws (D). Screw (D) Installation Manual Document Version 2009-12...
  • Page 77 3.2.6 Installation of 3- or 4-shelf System (Tower Type) Install 4 anchor plugs in the wall, using the wall brackets as a template. Fix the wall brackets to the wall with 4 screws (A). Notice • Drive mounting screws into the wall. Be careful to avoid touching any metal laths, wire laths or metal plates in the wall.
  • Page 78 3.2.6 Installation of 3- or 4-shelf System (Tower Type) Check that the shelves are standing exactly vertically. If the shelves are leaning slightly to one side, move the base stands to adjust the position. (Since the base stands are attached loosely to the floor, it should be possible to adjust the position of the shelves.) Then, tighten the screws connecting the base stands to the floor.
  • Page 79 3.2.6 Installation of 3- or 4-shelf System (Tower Type) Expansion Shelf 2 Lift Expansion Shelf 2, attach it to the metal bracket fixed on Expansion Shelf 1, and slide it backwards until it locks. Metal Bracket Secure Expansion Shelf to the metal bracket 2 with 2 screws (B). Screw (B) Installation of a 3-shelf system is complete.
  • Page 80 3.2.6 Installation of 3- or 4-shelf System (Tower Type) Mounting Expansion Shelf 3 For the 4-shelf system, attach the metal bracket (supplied with Expansion Shelf 3) to Expansion Shelf 2 first. Then, attach the wall brackets (supplied with the Mounting Kit) to Expansion Shelf 3. After mounting Expansion Shelf 3 on Expansion Shelf 2, fix Expansion Shelf 3 to the wall.
  • Page 81 3.2.6 Installation of 3- or 4-shelf System (Tower Type) Remove the 4 tabs on the top cover of Expansion Shelf 3, by using a flathead screwdriver, as shown below. Expansion Shelf 3 Fasten the wall brackets loosely to Expansion Shelf 3 with 4 screws (D). (This makes it easy to adjust the position of the shelves later.) Screw (D) Wall Bracket (Left)
  • Page 82 3.2.6 Installation of 3- or 4-shelf System (Tower Type) Lift Expansion Shelf 3, attach it to the metal bracket fixed on Expansion Shelf 2, and slide it backwards until it locks. Metal Bracket Installation Manual Document Version 2009-12...
  • Page 83 3.2.6 Installation of 3- or 4-shelf System (Tower Type) Secure Expansion Shelf 3 to the metal bracket with 2 screws (B). Screw (B) Document Version 2009-12 Installation Manual...
  • Page 84 3.2.6 Installation of 3- or 4-shelf System (Tower Type) Fixing to the Wall Install 4 anchor plugs in the wall, using the wall brackets as a template. Fix the wall brackets to the wall with 4 screws (A). Notice • Drive mounting screws into the wall.
  • Page 85 3.2.6 Installation of 3- or 4-shelf System (Tower Type) Check that the shelves are standing exactly vertically. If the upper shelves are leaning slightly to one side, move Expansion Shelf 3 to adjust the position. (Since the wall brackets are attached loosely to Expansion Shelf 3, it should be possible to adjust the position of the shelves.) Then, tighten the screws connecting the wall brackets to Expansion Shelf 3.
  • Page 86 3.2.6 Installation of 3- or 4-shelf System (Tower Type) Connecting Shelves For a 3- or 4-shelf system, you need to install an optional BUS-M card and BUS-ME card(s) in the Basic Shelf. To connect the shelves, plug the Bus Cables (supplied with the BUS-M card or BUS-ME card) into the slots of the BUS-M card.
  • Page 87 3.2.6 Installation of 3- or 4-shelf System (Tower Type) Push the release lever in the direction of the arrow so that the BUS-M card engages securely with the connector on the back board. Release Lever Back Board Turn the 2 screws clockwise to fix the BUS-M card in place. Screws Document Version 2009-12 Installation Manual...
  • Page 88 3.2.6 Installation of 3- or 4-shelf System (Tower Type) Plug each Bus Cable into the corresponding port of the BUS-M card in the Basic Shelf. Then, plug the other end into the BUS-S card in each Expansion Shelf. Note When plugging or unplugging the Bus Cables, make sure that the DC power supply is turned off. Bus Cable For Expansion Shelf 3...
  • Page 89 3.2.6 Installation of 3- or 4-shelf System (Tower Type) Attach the noise shield wires of each Bus Cable to the Basic Shelf and each Expansion Shelf with the screws of the BUS-M card. Note When attaching or removing the noise shield wires, make sure that the DC power supply is turned off. Screw Noise Shield Wire Document Version 2009-12...
  • Page 90: Installation Of 4-Shelf System (Side-By-Side Type)

    3.2.7 Installation of 4-shelf System (Side-by-side Type) 3.2.7 Installation of 4-shelf System (Side-by-side Type) When vertical space is limited, it is possible to install shelves side-by-side. Installing the system using base stands (supplied with an optional Mounting Kit) makes it easy to reinstall shelves in a different place. Construction of 4-shelf System (Side-by-side Type) Wall Bracket (Left)
  • Page 91 3.2.7 Installation of 4-shelf System (Side-by-side Type) Installing the Basic Shelf and Expansion Shelf 1 To install the Basic Shelf, attach the metal bracket (supplied with the Basic Shelf) to the base stands (supplied with the optional Mounting Kit) first. Then, install the base stands on the floor and fix the Basic Shelf to it. To install Expansion Shelf 1, attach the metal bracket (supplied with Expansion Shelf 1) to the Basic Shelf.
  • Page 92 3.2.7 Installation of 4-shelf System (Side-by-side Type) Place the metal bracket on the base stands. Metal Bracket Attach the metal bracket to the base stands with 4 screws (B). Screw (B) Installation Manual Document Version 2009-12...
  • Page 93 3.2.7 Installation of 4-shelf System (Side-by-side Type) Make 4 holes for anchor plugs on the floor, using the measurements indicated here. W a l l 95 mm (3-3/4 in) 510 mm 287 mm (20-1/16 in)* (11-5/16 in) Floor 382 mm (15-1/16 in) * If the direction of the base stands is reversed, the measurement must be 443.4 mm (17-7/16 in).
  • Page 94 3.2.7 Installation of 4-shelf System (Side-by-side Type) Install 4 anchor plugs in the holes on the floor. Then, fasten the base stands to the floor with 4 screws (A). Screw (A) Washer Hammer Anchor Plug 30 mm (1-3/16 in) 8 mm Anchor (5/16 in) Plug...
  • Page 95 3.2.7 Installation of 4-shelf System (Side-by-side Type) Lift the Basic Shelf, attach it to the metal bracket, and slide it backwards until it locks. Metal Bracket Secure the Basic Shelf to the metal bracket with 2 screws (B). Screw (B) Document Version 2009-12 Installation Manual...
  • Page 96 3.2.7 Installation of 4-shelf System (Side-by-side Type) Expansion Shelf 1 Fix the metal bracket to the Basic Shelf with 4 screws (B). Metal Bracket Screw (B) Remove the 4 tabs on the top cover of Expansion Shelf 1, by using a flathead screwdriver, as shown below. Expansion Shelf 1 Installation Manual Document Version 2009-12...
  • Page 97 3.2.7 Installation of 4-shelf System (Side-by-side Type) Fasten the wall brackets loosely to Expansion Shelf 1 with 4 screws (D). (This makes it easy to adjust the position of the shelves later.) Screw (D) Wall Bracket (Left) Wall Bracket (Right) Lift Expansion Shelf 1, attach it to the metal bracket fixed on the Basic Shelf, and slide it backwards until it locks.
  • Page 98 3.2.7 Installation of 4-shelf System (Side-by-side Type) Secure Expansion Shelf 1 to the metal bracket with 2 screws (B). Screw (B) Fixing to the Wall Install 4 anchor plugs in the wall, using the wall brackets as a template. Fix the wall brackets to the wall with 4 screws (A).
  • Page 99 3.2.7 Installation of 4-shelf System (Side-by-side Type) • When installing anchor plugs in the wall, be careful not to damage or dirty the shelves. Wall Bracket (Left) Wall Bracket (Right) Washer Anchor Plug Screw (A) 413 mm Hammer Anchor Plug (16-1/4 in) 8 mm (5/16 in)
  • Page 100 3.2.7 Installation of 4-shelf System (Side-by-side Type) Check that the shelves are standing exactly vertically. If the shelves are leaning slightly to one side, move the base stands to adjust the position. (Since the base stands are attached loosely to the floor, it should be possible to adjust the position of the shelves.) Then, tighten the screws connecting the base stands to the floor.
  • Page 101 3.2.7 Installation of 4-shelf System (Side-by-side Type) Installing Expansion Shelves 2 and 3 Repeat the procedure in "Installing the Basic Shelf and Expansion Shelf 1" for Expansion Shelves 2 and 3. Expansion Shelves 2 and 3 must be connected to the Basic Shelf using Bus Cables. Therefore, make sure that Expansion Shelves 2 and 3 are installed so that the Bus Cables can reach the Basic Shelf.
  • Page 102 3.2.7 Installation of 4-shelf System (Side-by-side Type) Connecting Shelves For the 4-shelf system, you need to install an optional BUS-M card and BUS-ME cards in the Basic Shelf. To connect the shelves, plug the Bus Cables (supplied with the BUS-M card or BUS-ME card) into the slot of the BUS-M card.
  • Page 103 3.2.7 Installation of 4-shelf System (Side-by-side Type) Push the release lever in the direction of the arrow so that the BUS-M card engages securely with the connector on the back board. Release Lever Back Board Turn the 2 screws clockwise to fix the BUS-M card in place. Screws Document Version 2009-12 Installation Manual...
  • Page 104 3.2.7 Installation of 4-shelf System (Side-by-side Type) Plug each Bus Cable into the corresponding port of the BUS-M card in the Basic Shelf. Then, plug the other end into the BUS-S card in each Expansion Shelf. Note When plugging or unplugging the Bus Cables, make sure that the DC power supply is turned off. Bus Cable For Expansion Shelf 3...
  • Page 105 3.2.7 Installation of 4-shelf System (Side-by-side Type) Attach the noise shield wires of each Bus Cable to the Basic Shelf and each Expansion Shelf with the screws of the BUS-M card. Note When attaching or removing the noise shield wires, make sure that the DC power supply is turned off. Screw Noise Shield Wire Document Version 2009-12...
  • Page 106: Wall Mounting (Kx-Tde600/Kx-Tde620)

    3.2.8 Wall Mounting (KX-TDE600/KX-TDE620) 3.2.8 Wall Mounting (KX-TDE600/KX-TDE620) Mounting Shelves WARNING • Make sure that the wall that the shelf will be attached to is strong enough to support the shelf. If not, it is necessary for the wall to be reinforced. •...
  • Page 107 3.2.8 Wall Mounting (KX-TDE600/KX-TDE620) Install 4 anchor plugs in the wall, using the metal bracket as a template. Fix the metal bracket with 4 screws (A). Anchor Plug W a ll Hammer Anchor Plug Metal Bracket 8 mm (5/16 in) 30 mm (1-3/16 in) Screw (A)
  • Page 108 3.2.8 Wall Mounting (KX-TDE600/KX-TDE620) Hook the shelf onto the metal bracket, making sure that the shelf slides down and onto the hooked parts of the metal bracket. Use 2 screws (B) to fix both sides of the shelf. Screw (B) Connecting Shelves For a multiple shelf system, you need to install an optional BUS-M card and BUS-ME card(s) in the Basic Shelf.
  • Page 109: Installing/Replacing The Power Supply Unit

    3.2.9 Installing/Replacing the Power Supply Unit 3.2.9 Installing/Replacing the Power Supply Unit Function PSU Type Lower/Upper Input Voltage Range Current Input Frequency Lower: 100 V AC to 130 V AC 2.5 A 50 Hz or 60 Hz PSU-M Upper: 200 V AC to 240 V AC 1.4 A Lower: 100 V AC to 130 V AC 5.1 A...
  • Page 110 3.2.9 Installing/Replacing the Power Supply Unit The following procedures are for installing or replacing a PSU only. Do not replace or remove the PSU for any other purpose. Installing the Power Supply Unit Insert the PSU along the guide rails. CAUTION For safety reasons, do not touch parts in the PSU.
  • Page 111: Replacing The Power Supply Unit

    3.2.9 Installing/Replacing the Power Supply Unit Turn the 4 screws clockwise, in the order indicated by the numbers 1 to 4, to fix the PSU. Screws Replacing the Power Supply Unit Unplug the AC power cord. Turn the 4 screws counterclockwise to loosen them. Screws Document Version 2009-12 Installation Manual...
  • Page 112 3.2.9 Installing/Replacing the Power Supply Unit Pull the release lever in the direction of the arrow to disconnect the PSU from the back board. Back Board Release Lever Replace the PSU. New PSU Current PSU Follow the steps in "Installing the Power Supply Unit". Installation Manual Document Version 2009-12...
  • Page 113: Frame Ground Connection

    3.2.10 Frame Ground Connection 3.2.10 Frame Ground Connection Loosen the screw. Screw Insert a grounding wire (user-supplied). Tighten the screw. Connect the grounding wire to ground. Repeat steps 1 to 4 for each shelf. Grounding wire To ground WARNING • Proper grounding (connection to ground) is very important to reduce the risk to the user of electrocution or to protect the PBX from the bad effects of external noise in the case of a lightning strike.
  • Page 114: Installing/Removing The Optional Service Cards

    3.2.11 Installing/Removing the Optional Service Cards 3.2.11 Installing/Removing the Optional Service Cards CAUTION • To protect the back board from static electricity, do not touch parts on the back board in the main unit and on the optional service cards. To discharge static electricity, touch ground or wear a grounding strap.
  • Page 115 3.2.11 Installing/Removing the Optional Service Cards Turn the 2 screws clockwise to fix the card in place. Screws Note Make sure the screws are tightened to ground the card securely. Document Version 2009-12 Installation Manual...
  • Page 116 3.2.11 Installing/Removing the Optional Service Cards Covering the Blank Slots Be sure to cover each slot in which no optional service card is installed by using a Blank Slot Cover. CAUTION Failure to install the Blank Slot Cover may cause electromagnetic interference. Installation Manual Document Version 2009-12...
  • Page 117 3.2.11 Installing/Removing the Optional Service Cards Removing the Optional Service Cards Turn the 2 screws counterclockwise to loosen them. Screws Pull the release lever in the direction of the arrow to disconnect the card from the back board. Pull the card from the shelf to remove it.
  • Page 118: Cable Handling

    3.2.12 Cable Handling 3.2.12 Cable Handling Note For safety reasons, do not stretch, bend, or pinch the AC power cord. Cable Handling for Each Shelf When cables are connected to the shelf, run the cables to either the right or the left, and then towards the back of the shelf as shown below.
  • Page 119 3.2.12 Cable Handling Cable Handling for Connected Shelves When running connected cables towards the back of the shelves, make sure not to block the opening of each Fan Guard as shown below. Fan Guard Document Version 2009-12 Installation Manual...
  • Page 120: Types Of Connectors

    3.2.13 Types of Connectors 3.2.13 Types of Connectors Connector Type Pin Number Used for • DHLC8 (KX-TDA0170) RJ11 • SLC8 (KX-TDA0173) • CSLC16 (KX-TDA0177) • ESLC16 (KX-TDA6174) • EMSLC16 (KX-TDA6175) • ECSLC24 (KX-TDA6178) • ELCOT16 (KX-TDA6181) (Twisted pair cable) • IPCEMPR RJ45 •...
  • Page 121 3.2.13 Types of Connectors Connector Type Pin Number Used for • Basic Shelf (KX-TDE600) RS-232C (Shielded cable) • IPCEMPR Mini Plug Document Version 2009-12 Installation Manual...
  • Page 122: Attaching A Ferrite Core

    3.2.14 Attaching a Ferrite Core 3.2.14 Attaching a Ferrite Core A ferrite core must be attached when: • an RJ45 connector is connected to IPCEMPR, IP-GW16 or IP-EXT16 cards, or • an Amphenol connector is connected to an extension card. The ferrite core is included with the card.
  • Page 123 3.2.14 Attaching a Ferrite Core Attaching to an Amphenol Connector For Extension Cards Pass the cable through the ferrite core, then close the case of the ferrite core. Attach the ferrite core 3 cm (1-3/16 in) away from the connector. The ferrite core is included with the card. 3 cm (1-3/16 in) If you need to open the ferrite core, use a flathead screwdriver to unlatch the case of the ferrite core.
  • Page 124: Fastening Amphenol Connector

    3.2.15 Fastening Amphenol Connector 3.2.15 Fastening Amphenol Connector An Amphenol 57JE-type connector is used on some of the optional service cards. To connect an Amphenol connector, use the spring latch or screw to fix the upper part and use Velcro® tape to fix the lower part of the connector.
  • Page 125 3.2.15 Fastening Amphenol Connector Amphenol Connector Pin Assignment Chart Below is an Amphenol connector pin assignment chart for all optional service cards that use the Amphenol connector. For more details, refer to the appropriate section in "3.7 Information about the CO Line Cards" and "3.8 Information about the Extension Cards".
  • Page 126: Surge Protector Installation

    3.2.16 Surge Protector Installation 3.2.16 Surge Protector Installation CAUTION Performing surge protection is essential. Make sure to follow the instructions in this section. Overview A massive electrical surge can be caused if lightning strikes a telephone cable 10 m (33 ft) above ground, or if a telephone line comes into contact with a power line.
  • Page 127 3.2.16 Surge Protector Installation Outside Installation (Main Building) Surge Protector CO Line (Another Building) CO Line Extn. PT-interface CS Terminal Board Surge Extn. Protector Extn. Extn. PT-interface CS Ground Extn.: Extension Line If you install an extension outside of the building, the following precautions are recommended: Install the extension wire underground.
  • Page 128 3.2.16 Surge Protector Installation Connect the grounding rod to the surge protector using a grounding wire with a cross-sectional area of at least 1.3 mm Bury the grounding rod near the protector. The grounding wire should be as short as possible. The grounding wire should run straight to the grounding rod.
  • Page 129: Information About The Main Processing Card

    3.3.1 IPCEMPR Card 3.3 Information about the Main Processing Card 3.3.1 IPCEMPR Card Function The IPCEMPR card is the preinstalled main processing card with built-in ESVM card feature (2-channel) and an Activation Key for CA Basic for 20 Users. The Virtual Cards (CO line/extension) can be installed in Virtual Slots of the IPCEMPR card and can be activated with the activation keys.
  • Page 130 3.3.1 IPCEMPR Card WARNING A lithium battery is used in the IPCEMPR card. There is a risk of explosion if the battery is replaced with the incorrect type. Dispose of used batteries according to the manufacturer’s instructions. CAUTION • The SD Memory Card contains software for all the processes of the PBX and all the customer data. It can be easily removed and taken away from the PBX by a third party.
  • Page 131: Led Indications

    3.3.1 IPCEMPR Card LED Indications Indication Color Description BATT ALARM Battery alarm indication • OFF: Normal ON: Alarm SD ACCESS Green SD memory card status • ON: Accessing 10BASE-T/ 2 LINK Green Link status indication 100BASE-TX • OFF: Off-line • ON: Linked normally •...
  • Page 132: Dsp16 Card (Kx-Tde0110) And Dsp64 Card (Kx-Tde0111)

    3.3.2 DSP16 Card (KX-TDE0110) and DSP64 Card (KX-TDE0111) 3.3.2 DSP16 Card (KX-TDE0110) and DSP64 Card (KX-TDE0111) Function DSP16: 16-channel digital signal processor card with a 4-Channel IP Trunk activation key and a 8-Channel IP Proprietary Telephone activation key preinstalled. Compliant with ITU-T G. 729A and G.711 codec methods.
  • Page 133 3.3.2 DSP16 Card (KX-TDE0110) and DSP64 Card (KX-TDE0111) • When installing the DSP16 or DSP64 card, hold down the shaded areas of the card to connect it firmly. Document Version 2009-12 Installation Manual...
  • Page 134: Ipcmec Card (Kx-Tde0105)

    3.3.3 IPCMEC Card (KX-TDE0105) 3.3.3 IPCMEC Card (KX-TDE0105) Function Memory expansion card to increase system data storage space. To be mounted on the IPCEMPR card. To install the IPCMEC card, first remove the preinstalled memory card from the IPCEMPR card. IPCEMPR Card inside Preinstalled...
  • Page 135: Rmt Card (Kx-Tda0196)

    3.3.4 RMT Card (KX-TDA0196) 3.3.4 RMT Card (KX-TDA0196) Function Analog modem card for remote communication with the PBX. V90 support. To be mounted on the IPCEMPR card. IPCEMPR Card inside Screw RMT Card Accessories and User-supplied Items Accessories (included): Screws ´ 2 User-supplied (not included): none Document Version 2009-12 Installation Manual...
  • Page 136: Information About The Virtual Cards

    3261, 3262, 3264, 3311, 3581, 3960 and 4028 protocols, and ITU-T G.729A and G.711 codec methods. Also supports T.38 protocol. Virtual 32-Channel VoIP Extension Virtual Card for 32 VoIP extensions. Compliant with Panasonic Card (V-IPEXT32) proprietary protocol. Virtual 32-Channel SIP Extension Card Virtual Card for 32 SIP Extensions.
  • Page 137: Information About The Optional Shelf Expansion Cards

    3.5.1 BUS-M Card (KX-TDA6110) 3.5 Information about the Optional Shelf Expansion Cards 3.5.1 BUS-M Card (KX-TDA6110) Function Optional shelf expansion card required when mounting Expansion Shelves. To be installed in the Basic Shelf only. LEDs Bus Cable Connector Noise Shield Connector Accessories and User-supplied Items Accessories (included): Bus Cable ´...
  • Page 138: Bus-Me Card (Kx-Tda6111)

    3.5.2 BUS-ME Card (KX-TDA6111) 3.5.2 BUS-ME Card (KX-TDA6111) Function Optional shelf expansion card required when mounting Expansion Shelf 2 or 3. To be mounted on the BUS-M card installed in the Basic Shelf. BUS-M Card inside BUS-ME Card Accessories and User-supplied Items Accessories (included): Bus Cable ´...
  • Page 139: Information About The Built-In Shelf Expansion Card

    3.6.1 BUS-S Card 3.6 Information about the Built-in Shelf Expansion Card 3.6.1 BUS-S Card Function Shelf expansion card, built in to an Expansion Shelf, for connecting to the Basic Shelf. Bus Cable Connector Noise Shield Connector WARNING A lithium battery is used in the BUS-S card. There is a risk of explosion if the battery is replaced with the incorrect type.
  • Page 140: Information About The Co Line Cards

    3.7.1 ELCOT16 Card (KX-TDA6181) 3.7 Information about the CO Line Cards 3.7.1 ELCOT16 Card (KX-TDA6181) Function 16-port analog CO line card with 4 power failure transfer (PFT) ports. A maximum of 2 CID8 cards can be mounted on the ELCOT16 card (refer to "3.7.2 CID8 Card (KX-TDA0193)"). Amphenol To CO line Accessories and User-supplied Items...
  • Page 141 3.7.1 ELCOT16 Card (KX-TDA6181) Pin Assignments Amphenol Connector Signal Name Function Signal Name Function Ring port 1 Tip port 1 Ring port 2 Tip port 2 Ring port 3 Tip port 3 Ring port 4 Tip port 4 Ring port 5 Tip port 5 Ring port 6 Tip port 6...
  • Page 142: Cid8 Card (Kx-Tda0193)

    3.7.2 CID8 Card (KX-TDA0193) 3.7.2 CID8 Card (KX-TDA0193) Function 8-port Caller ID signal type FSK/FSK (with Call Waiting Caller ID [Visual Caller ID])/DTMF. To be mounted on the ELCOT16 card. inside CID8 Card Screw S W 1 Accessories and User-supplied Items Accessories (included): Screws ´...
  • Page 143: T1 Card (Kx-Tda0187)

    3.7.3 T1 Card (KX-TDA0187) 3.7.3 T1 Card (KX-TDA0187) Function 1-port T1 CO line card. EIA/TIA standard compliant. LEDs RJ45 To NT1 Accessories and User-supplied Items Accessories (included): none User-supplied (not included): RJ45 connector CAUTION • T1 ports are SELV ports and should only be connected to SELV services. •...
  • Page 144 3.7.3 T1 Card (KX-TDA0187) Pin Assignments RJ45 Connector Signal Name Level [V] Function Receive data (+) Receive data (-) Reserved – – Transmit data (-) Transmit data (+) Reserved – – LED Indications Indication Color Description CARD STATUS Green/Red Card status indication •...
  • Page 145: Pri23 Card (Kx-Tda0290)

    3.7.4 PRI23 Card (KX-TDA0290) 3.7.4 PRI23 Card (KX-TDA0290) Function 1-port ISDN Primary Rate Interface card (23B channels). NI (North American standard ISDN protocol) compliant. LEDs RJ45 Accessories and User-supplied Items Accessories (included): none User-supplied (not included): RJ45 connector CAUTION • PRI ports are SELV ports and should only be connected to SELV services.
  • Page 146 3.7.4 PRI23 Card (KX-TDA0290) Pin Assignments RJ45 Connector Signal Name Level [V] Function Receive data (+) Receive data (-) Reserved – – Transmit data (-) Transmit data (+) Reserved – – LED Indications Indication Color Description CARD STATUS Green/Red Card status indication •...
  • Page 147: Ip-Gw4E Card (Kx-Tda0484)

    3.7.5 IP-GW4E Card (KX-TDA0484) 3.7.5 IP-GW4E Card (KX-TDA0484) Function 4-channel VoIP gateway card. Compliant with VoIP H.323 V.2 protocol, and ITU-T G.729A, G.723.1, and G. 711 codec methods. LEDs RJ45 (10BASE-T/100BASE-TX) To private IP network Accessories and User-supplied Items Accessories (included): CD-ROM (including documentation for web programming) ´ 1 User-supplied (not included): RJ45 connector Note •...
  • Page 148 3.7.5 IP-GW4E Card (KX-TDA0484) LED Indications Indication Color Description CARD STATUS Green/Red Card status indication • OFF: Power Off • Green ON: Normal (all ports are idle) • Green Flashing (60 times per minute): Normal (a port is in use) •...
  • Page 149: Ip-Gw16 Card (Kx-Tda0490)

    3.7.6 IP-GW16 Card (KX-TDA0490) 3.7.6 IP-GW16 Card (KX-TDA0490) Function 16-channel VoIP gateway card. Compliant with VoIP H.323 V.2 protocol, and ITU-T G.729A, G.723.1, and G. 711 codec methods. LEDs RJ45 (10BASE-T/100BASE-TX Full Duplex) To private IP network Accessories and User-supplied Items Accessories (included): Ferrite core ´...
  • Page 150 3.7.6 IP-GW16 Card (KX-TDA0490) LED Indications Indication Color Description CARD STATUS Green/Red Card status indication • OFF: Power Off • Green ON: Normal (all ports are idle) • Green Flashing (60 times per minute): Normal (a port is in use) •...
  • Page 151: Information About The Extension Cards

    3.8.1 CSIF4 Card (KX-TDA0143) and CSIF8 Card (KX-TDA0144) 3.8 Information about the Extension Cards 3.8.1 CSIF4 Card (KX-TDA0143) and CSIF8 Card (KX-TDA0144) Function CSIF4: 4-port CS interface card for 4 CSs. CSIF8: 8-port CS interface card for 8 CSs. RJ45 (LINE 1 to LINE 8) To CS Accessories and User-supplied Items...
  • Page 152 3.8.1 CSIF4 Card (KX-TDA0143) and CSIF8 Card (KX-TDA0144) Example: When the CSIF4 card has been installed The contents and design of the software are subject to change without notice. Pin Assignments RJ45 Connector Signal Name Function Reserved – Data port (High) POWH Power (High) POWL...
  • Page 153: Dhlc8 Card (Kx-Tda0170)

    3.8.2 DHLC8 Card (KX-TDA0170) 3.8.2 DHLC8 Card (KX-TDA0170) Function 8-port digital hybrid extension card for DPTs, APTs, SLTs, DSS consoles, and PT-interface CSs, with 2 power failure transfer (PFT) ports. Amphenol To extensions Accessories and User-supplied Items Accessories (included): Screws ´ 2, Ferrite core ´ 1 User-supplied (not included): Amphenol connector Note •...
  • Page 154 3.8.2 DHLC8 Card (KX-TDA0170) Pin Assignments Amphenol Connector Signal Signal Function Function Name Name SLT Ring port 1 SLT Tip port 1 PT Data port 1 PT Data port 1 (Low) (High) Reserved – Reserved – SLT Ring port 2 SLT Tip port 2 PT Data port 2 PT Data port 2...
  • Page 155 3.8.2 DHLC8 Card (KX-TDA0170) LED Indications Indication Color Description CARD STATUS Green/ Card status indication Orange/Red • OFF: Power Off • Green ON: Normal (all ports are idle) • Green Flashing (60 times per minute): Normal (a port is in use) •...
  • Page 156: Dlc8 Card (Kx-Tda0171)

    3.8.3 DLC8 Card (KX-TDA0171) 3.8.3 DLC8 Card (KX-TDA0171) Function 8-port digital extension card for DPTs, DSS consoles, and PT-interface CSs. Amphenol To extensions Accessories and User-supplied Items Accessories (included): Screws ´ 2, Ferrite core ´ 1 User-supplied (not included): Amphenol connector Note •...
  • Page 157 3.8.3 DLC8 Card (KX-TDA0171) Pin Assignments Amphenol Connector Signal Signal Function Function Name Name Reserved – Reserved – Data port 1 (Low) Data port 1 (High) Reserved – 28-29 Reserved – Data port 2 (Low) Data port 2 (High) Reserved –...
  • Page 158: Dlc16 Card (Kx-Tda0172)

    3.8.4 DLC16 Card (KX-TDA0172) 3.8.4 DLC16 Card (KX-TDA0172) Function 16-port digital extension card for DPTs, DSS consoles, and PT-interface CSs. Amphenol To extensions Accessories and User-supplied Items Accessories (included): Screws ´ 2, Ferrite core ´ 1 User-supplied (not included): Amphenol connector Note •...
  • Page 159 3.8.4 DLC16 Card (KX-TDA0172) Pin Assignments Amphenol Connector Signal Signal Function Function Name Name Data port 1 (Low) Data port 1 (High) Data port 2 (Low) Data port 2 (High) Data port 3 (Low) Data port 3 (High) Data port 4 (Low) Data port 4 (High) Data port 5 (Low) Data port 5 (High)
  • Page 160: Slc8 Card (Kx-Tda0173)

    3.8.5 SLC8 Card (KX-TDA0173) 3.8.5 SLC8 Card (KX-TDA0173) Function 8-port extension card for SLTs with 2 power failure transfer (PFT) ports. Amphenol To extensions Accessories and User-supplied Items Accessories (included): Screws ´ 2, Ferrite core ´ 1 User-supplied (not included): Amphenol connector Note •...
  • Page 161 3.8.5 SLC8 Card (KX-TDA0173) Pin Assignments Amphenol Connector Signal Signal Function Function Name Name Ring port 1 Tip port 1 Reserved – 27-28 Reserved – Ring port 2 Tip port 2 Reserved – 30-31 Reserved – Ring port 3 Tip port 3 Reserved –...
  • Page 162: Ext-Cid Card (Kx-Tda0168)

    3.8.6 EXT-CID Card (KX-TDA0168) 3.8.6 EXT-CID Card (KX-TDA0168) Function Sends Caller ID signals to extension ports. To be mounted on the SLC8 card only. inside SLC8 Card Screw EXT-CID Card Accessories and User-supplied Items Accessories (included): Screws ´ 2 User-supplied (not included): none Installation Manual Document Version 2009-12...
  • Page 163: Cslc16 Card (Kx-Tda0177), Eslc16 Card (Kx-Tda6174), Emslc16 Card (Kx-Tda6175), And Ecslc24 Card (Kx-Tda6178)

    Accessories (included): Screws ´ 2, Ferrite core ´ 1 User-supplied (not included): Amphenol connector Note • Panasonic SLT with Message Waiting Lamp is recommended for connection to the EMSLC16 card. • Attach the included ferrite core to the cable. Refer to "3.2.14 Attaching a Ferrite Core". •...
  • Page 164 3.8.7 CSLC16 Card (KX-TDA0177), ESLC16 Card (KX-TDA6174), EMSLC16 Card (KX-TDA6175), and ECSLC24 Card (KX-TDA6178) Pin Assignments Amphenol Connector Signal Name Function Signal Name Function Ring port 1 Tip port 1 Ring port 2 Tip port 2 Ring port 3 Tip port 3 Ring port 4 Tip port 4 Ring port 5...
  • Page 165 3.8.7 CSLC16 Card (KX-TDA0177), ESLC16 Card (KX-TDA6174), EMSLC16 Card (KX-TDA6175), and ECSLC24 Card (KX-TDA6178) LED Indications Indication Color Description CARD STATUS Green/Red Card status indication • OFF: Power Off • Green ON: Normal (all ports are idle) • Green Flashing (60 times per minute): Normal (a port is in use) •...
  • Page 166: Ip-Ext16 Card (Kx-Tda0470)

    3.8.8 IP-EXT16 Card (KX-TDA0470) 3.8.8 IP-EXT16 Card (KX-TDA0470) Function 16-channel VoIP extension card. Compliant with Panasonic proprietary protocol, and ITU-T G.729A and G. 711 codec methods. LEDs RJ45 (10BASE-T/100BASE-TX Full Duplex) To private IP network Accessories and User-supplied Items Accessories (included): Ferrite core ´ 1...
  • Page 167 If the LINK indicator is OFF, the ONLINE indicator will also be OFF. ALARM Alarm indication • OFF: Normal • ON: Alarm VoIP BUSY Green Panasonic proprietary VoIP protocol process indication • OFF: VoIP process inactive • ON: VoIP process active LINK Green Link status indication •...
  • Page 168: Information About The Other Cards

    3.9.1 OPB3 Card (KX-TDA0190) 3.9 Information about the Other Cards 3.9.1 OPB3 Card (KX-TDA0190) Function Optional 3-slot base card for mounting a maximum of 3 optional service cards from the following: • DPH4 card • EIO4 card • MSG4 card •...
  • Page 169: Dph4 Card (Kx-Tda0161)

    3.9.2 DPH4 Card (KX-TDA0161) 3.9.2 DPH4 Card (KX-TDA0161) Function 4-port doorphone card for 4 doorphones and 4 door openers. To be mounted on the OPB3 card. Fully insert the connectors through the panel openings. DPH4 Card OPB3 Card 8-pin Screw 10-pin Accessories and User-supplied Items Accessories (included): Screws ´...
  • Page 170 3.9.2 DPH4 Card (KX-TDA0161) Pin Assignments 8-pin Terminal Block Signal Name Function Doorphone 4 transmit com4 Doorphone 4 receive Doorphone 3 transmit com3 Doorphone 3 receive Doorphone 2 transmit com2 Doorphone 2 receive Doorphone 1 transmit com1 Doorphone 1 receive 10-pin Terminal Block Signal Name Function...
  • Page 171: Eio4 Card (Kx-Tda0164)

    3.9.3 EIO4 Card (KX-TDA0164) 3.9.3 EIO4 Card (KX-TDA0164) Function 4-port external input/output card. To be mounted on the OPB3 card. Fully insert the connectors through the panel openings. EIO4 Card OPB3 Card 8-pin Screw 10-pin Accessories and User-supplied Items Accessories (included): Screws ´ 3, 10-pin terminal block ´ 1, 8-pin terminal block ´ 1 User-supplied (not included): Copper wire Note For details about connection to external sensors and external relays, refer to "3.11.1 Connection of...
  • Page 172 3.9.3 EIO4 Card (KX-TDA0164) Pin Assignments 8-pin Terminal Block Signal Name Function Control 4 Control 4 com Control 3 Control 3 com Control 2 Control 2 com Control 1 Control 1 com 10-pin Terminal Block Signal Name Function Reserved – OP4b Opener 4 OP4a...
  • Page 173: External Sensor

    3.9.3 EIO4 Card (KX-TDA0164) External Sensor Power to the external sensor is provided from the EIO4 card and must be grounded through the EIO4 card as indicated in the diagram below. A pair of "sensor" and "common" lines are connected to the EIO4 card for each external sensor.
  • Page 174: Msg4 Card (Kx-Tda0191)

    3.9.4 MSG4 Card (KX-TDA0191) 3.9.4 MSG4 Card (KX-TDA0191) Function 4-channel message card. To be mounted on the OPB3 card. OPB3 Card inside MSG4 Card Screw Accessories and User-supplied Items Accessories (included): Screws ´ 3 User-supplied (not included): none Installation Manual Document Version 2009-12...
  • Page 175: Esvm4 Card (Kx-Tda0194)

    3.9.5 ESVM4 Card (KX-TDA0194) 3.9.5 ESVM4 Card (KX-TDA0194) Function 4-channel simplified voice message card for Built-in Simplified Voice Message feature. Also supports MSG card features. To be mounted on the OPB3 card. OPB3 Card inside ESVM Card Screw Accessories and User-supplied Items Accessories (included): Screws ´...
  • Page 176: Eecho16 Card (Kx-Tda6166)

    3.9.6 EECHO16 Card (KX-TDA6166) 3.9.6 EECHO16 Card (KX-TDA6166) Function 16-channel card for echo cancellation during conferences. Accessories and User-supplied Items Accessories (included): none User-supplied (not included): none Note To establish a conference call involving 6 to 8 parties, install an EECHO16 card and enable echo cancellation for conferences using the Maintenance Console.
  • Page 177: Connection Of Extensions

    3.10.1 Maximum Cabling Distances of the Extension Wiring (Twisted Cable) 3.10 Connection of Extensions 3.10.1 Maximum Cabling Distances of the Extension Wiring (Twisted Cable) Cable Maximum Distance 26 AWG: 222 m (728 ft) PT-interface CS 24 AWG: 347 m (1138 ft) 22 AWG: 500 m (1640 ft) CAT 5:...
  • Page 178 3.10.1 Maximum Cabling Distances of the Extension Wiring (Twisted Cable) PT-interface Console DHLC8 Card ü ü ü ü ü EMSLC16, ESLC16,ECSLC24, ü CSLC16, SLC8 Cards DLC16, DLC8 Cards ü ü ü "ü" indicates that the extension card supports the terminal. Installation Manual Document Version 2009-12...
  • Page 179: Parallel Connection Of The Extensions

    3.10.2 Parallel Connection of the Extensions 3.10.2 Parallel Connection of the Extensions Any SLT can be connected in parallel with an APT or a DPT as follows. Note In addition to an SLT, an answering machine, a fax machine or a modem (PC) can be connected in parallel with an APT or a DPT.
  • Page 180 3.10.2 Parallel Connection of the Extensions With DPT Parallel mode or eXtra Device Port (XDP) mode can be selected through system programming. If XDP mode is enabled through system programming, parallel connection is not possible. Refer to "13.1.2 Paralleled Telephone" and "5.1.7 Extension Port Configuration" in the Feature Manual for further information.
  • Page 181 3.10.2 Parallel Connection of the Extensions With KX-T7600 Series DPT To DHLC8 card 2-conductor wiring cord 4-conductor wiring cord Connect pins "T" and "R". Connect pins "T", "R", "D1" and "D2". TO MAIN UNIT / PABX TO TEL To DHLC8 card To SLT With Other DPT To DHLC8 card...
  • Page 182: Digital Extra Device Port (Digital Xdp) Connection

    3.10.3 Digital EXtra Device Port (Digital XDP) Connection 3.10.3 Digital EXtra Device Port (Digital XDP) Connection A DPT can be connected to another DPT on the Digital XDP connection. In addition, if the DPT is connected to a DHLC8 card, it can also have an SLT connected in Parallel mode or XDP mode. Note •...
  • Page 183 3.10.3 Digital EXtra Device Port (Digital XDP) Connection Using an EXtra Device Port To DLC8/DLC16 card 4-conductor wiring cord To DHLC8 card Connect pins "T", "R", 2-conductor wiring cord (for connection of SLT) "D1" and "D2". Connect pins "T" and "R". 4-conductor wiring cord Connect pins "T", "R", "D1"...
  • Page 184 3.10.3 Digital EXtra Device Port (Digital XDP) Connection With KX-T7600 Series DPT Using a Modular T-Adaptor To DLC8/DLC16 card Modular To DHLC8 card T-Adaptor (for connection of SLT) 2-conductor wiring cord Connect pins "T" and "R". 4-conductor wiring cord Connect pins "D1" and "D2". 4-conductor wiring cord Connect pins "D1"...
  • Page 185 3.10.3 Digital EXtra Device Port (Digital XDP) Connection Using an EXtra Device Port To DLC8/DLC16 card 4-conductor wiring cord To DHLC8 card Connect pins "T", "R", 2-conductor wiring cord (for connection of SLT) "D1" and "D2". Connect pins "T" and "R". 4-conductor wiring cord Connect pins "T", "R", "D1"...
  • Page 186: First Party Call Control Cti Connection

    3.10.4 First Party Call Control CTI Connection 3.10.4 First Party Call Control CTI Connection CTI connection between a PC and a KX-DT343/KX-DT346/KX-T7633/KX-T7636 DPT provides first party call control. The CTI connection is made via a USB interface (version 2.0), and uses the TAPI 2.1 protocol. A USB Module must be connected to the DPT.
  • Page 187: Connection Of Doorphones, Door Openers, External Sensors, And External Relays

    3.11.1 Connection of Doorphones, Door Openers, External Sensors, and External Relays 3.11 Connection of Doorphones, Door Openers, External Sensors, and External Relays 3.11.1 Connection of Doorphones, Door Openers, External Sensors, and External Relays The PBX supports a maximum of 64 doorphones, 64 door openers, 64 external sensors, and 64 external relays. Note Doorphones, door openers, external sensors, and external relays are user-supplied.
  • Page 188 3.11.1 Connection of Doorphones, Door Openers, External Sensors, and External Relays Note for KX-T7765 Users When loosening/tightening the screw, do not scratch the cabinet wall with the driver shaft. Cabinet Wall Pass the wires through the hole in the base cover, and attach the base cover to a wall using 2 screws. Screw To 8-pin terminal block Note...
  • Page 189 3.11.1 Connection of Doorphones, Door Openers, External Sensors, and External Relays Connection Use 8-pin and 10-pin terminal blocks (included with the card) for connection. While pressing down on the hole at the top of the terminal block using a screwdriver, insert the wire into the side hole as shown below.
  • Page 190: Connection Of Peripherals

    3.12.1 Connection of Peripherals 3.12 Connection of Peripherals 3.12.1 Connection of Peripherals Maximum Distance 5 m (16 ft) Cable Maximum Distance MNT Port 26 AWG to 22 AWG: 10 m (32 ft) CAT 5: 10 m (32 ft) BGM/ Music on Hold Cable Maximum Distance 26 AWG to 22 AWG: 10 m (32 ft)
  • Page 191 3.12.1 Connection of Peripherals BGM/MOH The PBX provides Background Music and Music on Hold. Up to 2 external music sources (e.g., user-supplied radios) can be connected to the PBX. CAUTION • Wiring should be done carefully to prevent undue force being exerted on the plug. Otherwise, sound may only be heard intermittently.
  • Page 192 3.12.1 Connection of Peripherals Connection Charts For connecting a printer/PC with a 9-pin RS-232C connector PBX (9-pin) Printer/PC (9-pin) Circuit Type Signal Signal Circuit Type Pin No. Pin No. (EIA) Name Name (EIA) RD (RXD) RD (RXD) SD (TXD) SD (TXD) ER (DTR) ER (DTR) DR (DSR)
  • Page 193 3.12.1 Connection of Peripherals • Clear To Send (CTS):…(input) An ON condition of circuit CS (CTS) indicates that the printer or the PC is ready to receive data from the unit. The unit does not attempt to transfer data or receive data when circuit CS (CTS) is OFF. •...
  • Page 194: Lan Connection

    3.13.1 LAN Connection 3.13 LAN Connection 3.13.1 LAN Connection Connection Chart for LAN Connection The PBX is equipped with a LAN port for connecting to a LAN so that IP telephones (IP-PTs, IP softphones, SIP Extensions), IP-CSs, PCs and a CTI Server can be connected on a private IP network. IP Softphone LAN Port Switching Hub...
  • Page 195: Power Failure Connections

    3.14.1 Power Failure Connections 3.14 Power Failure Connections 3.14.1 Power Failure Connections When the power supply to the PBX fails, power failure transfer (PFT) will switch from the current connection to the Power Failure Connection. Refer to "13.1.11 Power Failure Transfer" in the Feature Manual for further information.
  • Page 196 3.14.1 Power Failure Connections RJ11 Connector Pin Assignments for CO line Card PFT Ports 1 and 2 Signal Name Function Ring port 2 Ring port 1 Tip port 1 Tip port 2 PFT Ports 3 and 4 Signal Name Function Ring port 4 Ring port 3 Tip port 3...
  • Page 197: Starting The Pbx

    3.15.1 Starting the PBX 3.15 Starting the PBX 3.15.1 Starting the PBX Before Starting the PBX Before starting the PBX, please pay attention to the following points: • SD Memory Card Notice The SD Memory Card must be inserted in the SD Memory Card slot of the IPCEMPR card before startup.
  • Page 198 3.15.1 Starting the PBX System Initialization Procedure Slide the System Initialize Switch to the "SYSTEM INITIALIZE" position. RUN Indicator Reset Button RESET SYSTEM INITIALIZE NORMAL System Initialize Switch Plug the AC power cord into the PBX and an AC outlet, and turn on the PBX. The RUN indicator will flash. Note For safety reasons, do not stretch, bend, or pinch the AC power cord.
  • Page 199 3.15.1 Starting the PBX LED Indications For the Basic Shelf Indication Color Description Green PBX status indication • OFF: Power Off (includes normal reset) • ON: Power On and running (on-line) • Flashing (60 times per minute): Starting up • Flashing (120 times per minute): Starting up or resetting with: •...
  • Page 200 3.15.1 Starting the PBX For an Expansion Shelf Indication Color Description Green Expansion shelf status indication • OFF: Power Off (includes normal reset) • ON: Power On and running (on-line) • Flashing (60 times per minute): Starting up • Flashing (120 times per minute): Program error in the BUS-S card ALARM Alarm indication •...
  • Page 201: Guide For The Maintenance Console

    Section 4 Guide for the Maintenance Console Explains the installation procedure, structure, and basic information of the Maintenance Console. Document Version 2009-12 Installation Manual...
  • Page 202: Overview

    4.1.1 Overview 4.1 Overview 4.1.1 Overview Maintenance Console is designed to serve as an overall system programming reference for the PBX. To program and administer the PBX by PC, you need to install the Maintenance Console onto the PC. This section describes overview and installation of the Maintenance Console only. Menu Bar System Menu Note...
  • Page 203: Pc Connection

    4.2.1 PC Connection 4.2 PC Connection 4.2.1 PC Connection Connection via MNT Port of IPCEMPR Card MNT Port To LAN Port Notice When connecting a PC to the PBX, a fixed IP address must be assigned to the PC. For information about fixed IP addresses, ask your network administrator.
  • Page 204 4.2.1 PC Connection CAUTION To protect the system, keep the following in mind: Make sure that both connector cases (frame ground) of the RS-232C cross cable (shielded cable)/USB cable are conductive. If they are not conductive, make sure that both connector cases of the cable are firmly connected.
  • Page 205 4.2.1 PC Connection • Data compression should be disabled. • Error Correction is not necessary. Note • An AT command (for initialization, enabling automatic answer, etc.) can only be programmed by Maintenance Console. "AT&F" is stored as the default value. •...
  • Page 206: Installation Of The Maintenance Console

    4.3.1 Installing and Starting the Maintenance Console 4.3 Installation of the Maintenance Console 4.3.1 Installing and Starting the Maintenance Console System Requirements Required Operating System • Microsoft Windows XP or Windows Vista Business operating system ® ® ® Minimum Hardware Requirements •...
  • Page 207 4.3.1 Installing and Starting the Maintenance Console Click Connect. Select KX-TDE600 from PBX Model. Select the LAN or RS-232C tab, depending on the type of PC connection with the PBX. Specify the settings as required. Note When connecting to the PBX for the first time selecting LAN, the IP Address and Port Number must be set to 192.168.0.101 and 35300 respectively.
  • Page 208 4.3.1 Installing and Starting the Maintenance Console • The PC will not perform any shutdown operation, or enter the power-saving system standby mode while the Maintenance Console is connected to the PBX. To perform either of the operations above, first close the connection to the PBX. CAUTION Do not remove the SD Memory Card while power is supplied to the PBX.
  • Page 209: Troubleshooting

    Section 5 Troubleshooting This section provides information on the PBX and telephone troubleshooting. Document Version 2009-12 Installation Manual...
  • Page 210: Troubleshooting

    5.1.1 Installation 5.1 Troubleshooting 5.1.1 Installation PROBLEM PROBABLE CAUSE SOLUTION You cannot make/receive • • IP-EXT/IP-GW/DSP Replace the corresponding card. calls via an IP network. card malfunction • • IPCEMPR card Replace the IPCEMPR card (be sure to malfunction turn off the PBX when replacing). •...
  • Page 211 5.1.1 Installation PROBLEM PROBABLE CAUSE SOLUTION Extensions (except IP-PT/ • • Extension card Replace the corresponding card. SIP Extension) do not malfunction operate. • • Poor connection Take the extension and plug it into the between the PBX and same extension port using a short the extension telephone cord.
  • Page 212 5.1.1 Installation PROBLEM PROBABLE CAUSE SOLUTION Alternate Calling—Ring/ • • Voice-calling mode and Switch the calling mode to ring-calling. Voice and Live Call Hands-free mode with • Set the LCS mode to "Private". Screening (LCS) do not LCS are not available function as set when using a with Wireless Phones.
  • Page 213 5.1.1 Installation PROBLEM PROBABLE CAUSE SOLUTION Extensions connected to an • • Bus Cable is not Connect the Bus Cables properly. Expansion Shelf do not connected properly. send a dial tone. • • Optional service card Replace the corresponding shelf malfunction: BUS-S expansion card.
  • Page 214: Connection

    5.1.2 Connection 5.1.2 Connection Connection between the PBX and a PT: CAUSE SOLUTION Can you dial The T/R is connected to the D1/D2. Use the correct cord (the an extension? inner 2 wires are for T/R and the outer 2 wires are for D1/D2).
  • Page 215 5.1.2 Connection Connection between the central office and the PBX: CAUSE SOLUTION (Continued from the CO line is connected to the T2/T1. Reconnect the CO line to previous page.) the T1/R1 or T2/R2 of the telephone jack using 2-conductor wiring. Can you dial out on a CO line...
  • Page 216: Operation

    5.1.3 Operation 5.1.3 Operation PROBLEM PROBABLE CAUSE SOLUTION • • • Cannot set the IP An unusable value is Set an IP address within the valid range. address, subnet mask being set. IP address of the IP-PT/PBX: "1.0.0.0" to address, and PBX IP "223.255.255.255"...
  • Page 217 5.1.3 Operation PROBLEM PROBABLE CAUSE SOLUTION • • • During a power failure, A DPT or APT is Disconnect the DPT or APT and connect extensions connected connected to the an SLT. to ports 1 to 4 of extension port. •...
  • Page 218: Using The Reset Button

    5.1.4 Using the Reset Button 5.1.4 Using the Reset Button If the PBX does not operate properly, use the Reset Button. Before using the Reset Button, try the system feature again to confirm whether there definitely is a problem or not. CAUTION In order to avoid possible corruption of data on the SD Memory Card, please ensure that the "SD ACCESS"...
  • Page 219: Troubleshooting By Error Log

    5.1.5 Troubleshooting by Error Log 5.1.5 Troubleshooting by Error Log When a major system error occurs in the PBX, the ALARM indicator on the front of the Basic Shelf turns on red, and the system logs the error information. Error Log Display Format Below is the display format of the error log.
  • Page 220 5.1.5 Troubleshooting by Error Log Item Description Sub Code The 6-digit sub code of the relevant hardware (WXYYZZ). • W: Shelf type – Physical shelf: " " (blank) – Virtual shelf: "*" (asterisk) • X: Shelf number – 1: Basic Shelf –...
  • Page 221: Appendix

    Section 6 Appendix Document Version 2009-12 Installation Manual...
  • Page 222: Revision History

    6.1.1 PGMPR Software File Version 3.0xxx 6.1 Revision History 6.1.1 PGMPR Software File Version 3.0xxx New Options • System Components Table – Activation Key for CA Basic for 1 User (CA Basic 1user) KX-NCS2101 – Activation Key for CA Basic for 5 Users (CA Basic 5users) KX-NCS2105 –...
  • Page 223: Index

    Index Document Version 2009-12 Installation Manual...
  • Page 224 Index 8-Channel IP Softphone/IP Proprietary Telephone Activation Numerics Key (KX-NCS4208) 16-Channel Echo Canceller Card (KX-TDA6166) 29, 176 8-Channel SIP Extension Activation Key 16-Channel IP Proprietary Telephone Activation Key (KX-NCS4708) (KX-NCS4516) 8-Port Caller ID Card (KX-TDA0193) 29, 142 16-Channel IP Softphone/IP Proprietary Telephone Activation 8-Port Digital Extension Card (KX-TDA0171) 28, 156 Key (KX-NCS4216)
  • Page 225 Index Cable Distance Fan Guard Cable Handling for Connected Shelves Ferrite Core Cable Handling for Each Shelf First Party Call Control CTI Connection Characteristics Frame Ground Connection CID8 Card (KX-TDA0193) Front Cover, Closing CO Line Connection Front Cover, Opening Components, System Connecting Shelves, 2-shelf System Connecting Shelves, 3-shelf System Information about the Virtual Cards...
  • Page 226 KX-TDA0193 (8-Port Caller ID Card) 29, 142 KX-TDA0194 (4-Channel Simplified Voice Message Pager Card) 29, 175 Panasonic Proprietary Telephones, Compatible KX-TDA0196 (Remote Card) 29, 135 Panasonic Proprietary Telephones, Incompatible KX-TDA0290 (PRI Card [PRI23]) 29, 145 Parallel Connection of the Extensions...
  • Page 227 Index SD Memory Card Slave DPT, Digital XDP SLC8 Card (KX-TDA0173) Slot for the IPCEMPR Card Slots for Physical Cards (Free Slots) Slots for Virtual CO Line Cards Slots for Virtual Extension Cards Specifications Specifications, Characteristics Specifications, General Description Specifications, System Capacity Starting the PBX Supplied Items for an Expansion Shelf (KX-TDE620) Supplied Items for the Basic Shelf (KX-TDE600)
  • Page 228 Copyright: This material is copyrighted by Panasonic System Networks Co., Ltd., and may be reproduced for internal use only. All other reproduction, in whole or in part, is prohibited without the written consent of Panasonic System Networks Co., Ltd. © Panasonic System Networks Co., Ltd. 2009...

This manual is also suitable for:

Tde600Kxtda620Tda620Kx-tde620Tde620

Table of Contents