Related Manuals for Automatic Technology GDO-7v2 SecuraLift
Summary of Contents for Automatic Technology GDO-7v2 SecuraLift
- Page 1 GDO-7v2 SecuraLift ® Overhead Garage Door Opener Featuring TrioCode ™ Technology Part # 13215 (Manual) INSTALLATION INSTRUCTIONS | OWNERS COPY...
- Page 2 Automatic Technology Australia Pty Ltd to the extent that such may be lawfully excluded hereby expressly disclaims all conditions or warranties, statutory or otherwise which may be implied by laws as conditions or warranties of purchase of an Automatic Technology Australia Pty Ltd Garage Door Opener.
-
Page 3: Table Of Contents
GDO-7v2 SecuraLift ® Overhead Garage Door Opener Important Safety Instructions Features Operating Controls Package Contents Installation Tube Rail Assembly Determine the Door Type Mounting on a Track Type Door Mounting on a non-Track Type Door Mounting Door Bracket & Arms... -
Page 4: Important Safety Instructions
Beam. In most countries P.E. Beams are mandatory on all garage doors fi tted with automatic openers. For a small additional outlay Automatic Technology recommends that Photo Electric Beams be installed with the automatic opener ensuring additional safety and peace of mind. - Page 5 If the power supply cord is damaged, it must be replaced by an Automatic Technology service agent or suitably qualifi ed person. Make sure that the door is fully open before driving in or out of the garage and fully closed before leaving the driveway.
-
Page 6: Features
Features Thank you for purchasing the Automatic Technology SecuraLift® Automatic Garage Door Opener. Designed by our renowned engineers to suit sectional overhead and one piece tilt up doors, the SecuraLift® will provide years of smart, simple & secure convenience to your home. - Page 7 This will allow you to manually open or close the door. To re-engage the opener pull the string Owner Installation Instructions GDO-7v2 SecuraLift®...
-
Page 8: Operating Controls
The shunt has to be removed when connecting a Photo Electric Beam. NOTE: P.E. Shunt must only be removed when P.E. Beams are being connected, otherwise the opener will malfunction. PROG INPUT is used to connect of the Automatic Technology Handheld Programmer for the purpose of editing control and receiver functions. - Page 9 Owner Installation Instructions GDO-7v2 SecuraLift®...
-
Page 10: Package Contents
Package Contents GDO-7V2 Securalift ® drive unit TrioCode ™ keyring transmitters TrioCode ™ wall mounted transmitters (not available all models) Tubes Tube inserts Pipe support assembly (either steel or plastic version) Chain Shuttle assembly Door attachment arms Hardware pack Installation Manual GDO-7v2 SecuraLift®... -
Page 11: Installation
DO NOT OVERTIGHTEN CHAIN - it must have approximately 6 to 12mm of sag. Engaged Ensure the chain is not twisted before tightening nuts. position Disengaged When the tension is fi nalised, tighten lock nuts at position both ends of chain index. Owner Installation Instructions GDO-7v2 SecuraLift®... -
Page 12: Determine The Door Type
Step 5. fi g One piece door with track For a one-piece door without tracks (on springs) (Fig. 07) proceed with the installation from Step 9. Door fi g One piece door without track GDO-7v2 SecuraLift® Owner Installation Instructions... -
Page 13: Mounting On A Track Type Door
Go to Step 14 on page 14. fi g WARNING: The opener must be securely fastened to structural supports otherwise opener failure may ensue, causing serious personal injury and/or property damage. Owner Installation Instructions GDO-7v2 SecuraLift®... -
Page 14: Mounting On A Non-Track Type Door
Strips should not extend more than 18mm below centre of powerhead mounting holes (Fig. 11). fi g WARNING: The opener must be securely fastened to structural supports, otherwise opener failure may ensue causing serious personal injury Pipe support assembly and/or property damage. GDO-7v2 SecuraLift® Owner Installation Instructions... -
Page 15: Mounting Door Bracket & Arms
If installing on a door with a bad wave action, lengthening the arm will assist in reducing this effect. IMPORTANT NOTE: Adjust the length of the cord so that its toggle is no more than 1.8m from the ground. fi g Owner Installation Instructions GDO-7v2 SecuraLift®... -
Page 16: Programming The Opener
Press and hold the MINUS (-) button for six (6) seconds until you hear three beeps and the CLOSE LIMIT LED starts to fl ash (Fig. 21). Release the CLOSE button. Repeat Steps 15.1 to 15.4 to set new travel limit positions.. GDO-7v2 SecuraLift® Owner Installation Instructions... -
Page 17: Setting Limits: Via Transmitter
Follow Steps 15.5 (a) and (b), as outlined overleaf. Repeat Steps 16.1 and 16.3 to set new travel limit positions. » There is no need to re-code the transmitter (Step 16.2) upon restting travel limits. The transmitter will still be stored in memory. Owner Installation Instructions GDO-7v2 SecuraLift®... -
Page 18: Safety Obstruction Force
fi g DANGER! If the door fails these tests, put the opener into manual mode, only operate the door by hand and call for service. Wood (40mm high) GDO-7v2 SecuraLift® Owner Installation Instructions... -
Page 19: Adjusting Safety Obstruction Forces
Step 18.3 - To Recall Factory Set Force While holding down the FORCE MARGIN SET button, press the LIMIT SET button for two (2) seconds. Release both buttons. The default setting should now be recalled. Owner Installation Instructions GDO-7v2 SecuraLift®... -
Page 20: Coding Transmitters
fi g Release LIGHT CODE and MINUS (-) buttons. To test, press and hold the transmitter button for fi ve seconds to set Vacation Mode. To reset Vacation Mode press the same button for two seconds. GDO-7v2 SecuraLift® Owner Installation Instructions... -
Page 21: Remotely Coding Transmitters
These LED’s will turn off and the CODING LED will illuminate. Release the DOOR CODE BUTTON. All stored codes will now be deleted. Confi rm this pressing buttons on any previously coded transmitters - the opener should not respond. Owner Installation Instructions GDO-7v2 SecuraLift®... -
Page 22: Accessories
OPEN LIMIT LED will fl ash to indicate that Auto- close mode is operational. Break the P.E. Beam’s path momentarily to initialise Auto-close. When the door reaches the fully opened position, the door will pause for the set Auto-close time and then close. GDO-7v2 SecuraLift® Owner Installation Instructions... -
Page 23: Final Set Up
(4) times (depending on the position of the door and the power up condition). A single beep will be heard once the initialisation is complete. The door is now ready for use. Owner Installation Instructions GDO-7v2 SecuraLift®... -
Page 24: Parameters
Door obstructed when closing Flashing Beeps as door moves Opener overloaded Alternating fl ashes Alternating fl ashes Door in open position with Auto- One second fl ashes Close mode selected Mains power interrupted Rapid fl ashes GDO-7v2 SecuraLift® Owner Installation Instructions... -
Page 25: Button Functions
Deletes all transmitter storage memory are off SET & DOOR CODE (the power on) and hold until all Deletes all control parameters and transmitter storage LEDs are off memory. Re-initialises the Opener to re-calculate force margin Owner Installation Instructions GDO-7v2 SecuraLift®... -
Page 26: System Specifi Cations
2. Intermittent operations may occur in areas which experience very strong winds. Strong wind puts extra pressure on the door and tracks which may in turn trigger the safety obstruction detection system intermittently. GDO-7v2 SecuraLift® Owner Installation Instructions... -
Page 27: Troubleshooting Guide
In such an instance please contact your Automatic Technology dealer for an alternative frequency replacement kit. As this is not a warrantable situation but an environmental issue charges may apply for the change-over. -
Page 28: Maintenance
Maintenance Maintenance Yearly The SERVICE LED will indicate the requirement for Automatic Technology suggests you contact your installer a service and/or adjustment. To reset the SERVICE to perform an annual door service. LED when the door is serviced, reprogram the Door Travel Limits and the Door Travel Force –... -
Page 29: Spare Parts
Spare Parts Owner Installation Instructions GDO-7v2 SecuraLift®... -
Page 30: Warranty
Trade Practices Act 1974 (Cwth). 2. Subject to all of the matters set out below, Automatic Technology Australia Pty Ltd (“ATA”) warrants: (a) overhead door opener drive units for twenty four (24) months or 5000 cycles, whichever occurs fi rst; and (b) all components and accessories for twelve (12) months, from the date of purchase (specifi... - Page 31 Owner Installation Instructions GDO-7v2 SecuraLift®...
- Page 32 © January 2008 Automatic Technology (Australia) Pty Ltd. All rights reserved. TrioCode™ and SecuraLift® are trademarks of Automatic Technology (Australia) Pty Ltd. No part of this document may be reproduced without prior permission. In an ongoing commitment to product quality we reserve the right to change specifi cation without notice. E&OE.
Need help?
Do you have a question about the GDO-7v2 SecuraLift and is the answer not in the manual?
Questions and answers