Canon imageRUNNER 3300 Series Copying Manual
Hide thumbs Also See for imageRUNNER 3300 Series:
Table of Contents

Advertisement

Series
Copying Guide
Copying Guide
Please read this guide before operating this equipment.
After you finish reading this guide, store it in a safe place for future reference.

Advertisement

Table of Contents
loading

Summary of Contents for Canon imageRUNNER 3300 Series

  • Page 1 Series Copying Guide Copying Guide Please read this guide before operating this equipment. After you finish reading this guide, store it in a safe place for future reference.
  • Page 2: Setup Guide

    About the Manuals for the Machine The manuals for this machine are divided as follows. Please read them to suit your needs. For Basic Use ..........Reference Guide Troubleshooting ..........For Basic Copying ........... Copying Guide For Convenient Copying ........(This Document) For Basic Mail Box Function Use ......
  • Page 3: How This Manual Is Organized

    Canon, Inc. • Considerable effort has been made to make sure that this manual is free of inaccuracies and omissions. • However, as we are constantly improving our products, if you need an exact specification, please contact Canon.
  • Page 4: Table Of Contents

    Table of Contents How This Manual Is Organized ........ii Table of Contents.
  • Page 5 Two-sided Copying (Two-sided Mode) ......1-56 Making Two-sided Copies from One-sided Originals (1 2-Sided) . . 1-57 Making Two-sided Copies from Two-sided Originals (2 2-Sided) .
  • Page 6 Erasing a Copy Job ........2-54 Recalling a Previous Copy Setting (Recall) .
  • Page 7: How To Use This Manual

    How to Use This Manual Symbols Used in This Manual The following symbols are used in this manual, for explanations of procedures and restrictions, handling cautions, and instructions that should be observed for safety. Indicates a warning concerning operations that may lead to death or injury WARNING to persons if not performed correctly.
  • Page 8: Displays Used In This Manual

    Displays Used in This Manual Screenshots of the touch panel display used in this manual are those taken when the Finisher-J1, Cassette Feeding Unit-W1, Feeder (DADF-H1), Printer Kit, and FAX Board are attached to the imageRUNNER 3300. Note that functions that cannot be used depending on the model or options, are not displayed on the touch panel display.
  • Page 9: Basic Copying

    Basic Copying CHAPTER This chapter describes the basic copy functions. What the imageRUNNER 3300/2800/2200 Series Machine Can Do ....1-3 Various Kinds of Copies ............1-3 Flow of Copy Operations .
  • Page 10 1. Basic Copying Interrupting the Current Job to Make Priority Copies (Interrupt Mode)....1-69 Checking a Sample Set Before Copying (Sample Set)......1-71 Checking the Copy Mode Settings (Setting Confirmation) .
  • Page 11: What The Imagerunner 3300/2800/2200 Series Machine Can Do

    What the imageRUNNER 3300/2800/2200 Series Machine Can Do Most operations of this machine are done from the touch panel display. To use the copy function of this machine, press keys in accordance with the messages displayed on the touch panel display. Various Kinds of Copies Copy Basic Features screen The screen on the left, which appears when the...
  • Page 12 When you select “Collate” See p. 1-44. R E P O R T R E P O R T Press to select or cancel Collate, Group, R E P O R T or Staple modes. R E P O R T R E P O R T When you select “1 2-Sided”...
  • Page 13 Special Features screen 1/2 The screen on the left, which appears on the touch panel display when you press “Special Features” in the Copy Basic Features screen, is called the Special Features screen. This screen is divided into two ▼ ▲...
  • Page 14 Transparencies See p. 2-15. R E P O R T R E P O R T R E P O R T Press to select or cancel the Transparency Interleaving mode. This mode enables you to insert a sheet between each transparency when copying transparencies.
  • Page 15 When you select “1 To 2.” See p. 2-39. Press to select or cancel the Image Separation mode. This mode enables you to divide an original into 2 or 4 sections and enlarge each section onto a copy sheet of a specified size. 11"x17"...
  • Page 16 Special Features screen 2/2 See p. 2-58. SCENE SCENE Press to make copies with the entire black/white image inverted. See p. 2-59. CITY CITY Press to copy an original with the image repeated in the vertical or horizontal CITY direction. See p.
  • Page 17: Flow Of Copy Operations

    Flow of Copy Operations This section describes the flow of basic copy operations. NOTE • For the following items, see the Reference Guide: - Main power and control panel power - Routine maintenance Press (Copy). COPY COPY MAIL BOX SCAN If the message <You must insert a control card>...
  • Page 18: Place Your Original

    If the message <Enter the Department ID and Password using the numeric keys.> appears, enter the Department ID and Password. (See the Reference Guide.) Place your original. NOTE • For instructions on placing the original, see the Reference Guide. • When Auto Collate is set to “On,”...
  • Page 19 Set the desired copy mode in the Special Features screen. ▼ ▲ The Special Features screen is divided into two screens. Press “ ”or “ ” to select the desired mode. You can continue setting other available modes. (See ‘Useful Copy Functions,’ in Chapter Enter the copy quantity.
  • Page 20 Press (Start). Clear Stop Start Power Copying starts. When scanning is completed, remove the original. If the optional Card Reader-C1 is attached, remove the control card. (See the Reference Guide.) If you have set the Department ID Management, press (ID). (See the Reference Guide.) IMPORTANT •...
  • Page 21 ● When the following screen is displayed: Follow the instructions in the screen, and press (Start) once for each original. When scanning is completed, press “Done.” ● When you want to copy a different original while printing: Press “Done,” and place your originals. Then Press (Start).
  • Page 22 ● When you want to stop a copy job: Press (Stop). Clear Stop Start Power For instructions on canceling a copy job, see the Reference Guide. NOTE • After you have pressed (Stop), several copies may be output from the machine. •...
  • Page 23: Entering The Copy Quantity

    Entering the Copy Quantity The machine allows up to 999 copies to be made. The maximum number of copies allowable can be changed. For details, contact your service representative. Specifying the Required Number of Copies Press (numeric keys) to enter the desired copy quantity (1 to 999).
  • Page 24: Changing The Copy Quantity

    Changing the Copy Quantity Press (Clear) to clear the entered number. ON / OFF Clear Stop Start Press (numeric keys) to enter the desired copy quantity (1 to 999). Clear Reset Guide Additional Functions Interrupt OPER The copy quantity appears on the upper right side of the Basic Features screen. IMPORTANT •...
  • Page 25: Selecting The Copy Paper Size (Paper Select)

    Selecting the Copy Paper Size (Paper Select) You can set the machine to automatically select the paper size, or you can specify the paper size for a copy job. NOTE • When copying an original onto the same size paper at a 100% copy ratio, the periphery of the original may be cut slightly on the copy.
  • Page 26 Place your original, and press “Paper Select.” Select “Auto,” and press “Done.” The following screen is displayed. Press (Start). Copying starts. 1-18 Selecting the Copy Paper Size (Paper Select)
  • Page 27: Specifying Paper Size/Type (Manual Paper Selection)

    Specifying Paper Size/Type (Manual Paper Selection) You can make copies after selecting the paper size and type (color, recycled, etc.) of paper loaded in the paper drawer. Place your originals, and press “Paper Select.” NOTE • The default setting is “Auto.” Select the desired paper size.
  • Page 28 ● When you select “Stack Bypass Setting”: Select the paper size, and press “Next.” Select the paper type, and press “OK.” NOTE • When placing paper other than a standard size, press “Free Size.” • When loading envelopes, press “Envelope.” •...
  • Page 29 The display returns to the Basic Features screen, and the selected paper size is displayed. Press (Start). Copying starts. NOTE • To cancel all settings and return the machine to the Standard mode, press (Reset). Selecting the Copy Paper Size (Paper Select) 1-21...
  • Page 30: Adjusting Exposure And Image Quality

    Adjusting Exposure and Image Quality The exposure and image quality can be adjusted when the original is scanned. NOTE • You can also change the exposure while printing. (See ‘Changing the Copy Exposure During Printing,’ on p. 1-26.) Adjusting Copy Exposure You can manually adjust the exposure to the most appropriate level for the original.
  • Page 31: Selecting Image Quality

    Selecting Image Quality You can adjust image quality to the level best suited to the quality of text or photo originals. The following three modes are available for adjusting image quality: Text/Photo mode Photo mode Text mode The world s coral reefs, where The world s coral reefs, where brilliantly colored fish and a brilliantly colored fish and a...
  • Page 32 Place your originals, press “ ,” and select the type of original (Text, Text/Photo, or Photo). When <Photo Mode> in Copy Settings is set to on, you can select “Printed Img.” or “Photo.” (See ‘Setting the Photo Mode of the Copy Function,’ on p. 3-9.) Press “Light”...
  • Page 33: Automatic Adjustment Of Exposure And Image Quality

    Press (Start). Copying starts. NOTE • To cancel the copy exposure setting, press “A.” • To cancel all settings and return the machine to the Standard mode, press (Reset). Automatic Adjustment of Exposure and Image Quality Place your originals, and press “A.” The exposure is automatically adjusted to the level best suited to the quality of the original.
  • Page 34: Changing The Copy Exposure During Printing

    Changing the Copy Exposure During Printing The copy exposure can be changed during printing. Press “Light” or “Dark,” in the screen displayed during printing. Move the indicator above “Light” and “Dark” to the left to make the exposure lighter, or to the right to make the exposure darker.
  • Page 35: Changing The Copy Ratio (Copy Ratio)

    Changing the Copy Ratio (Copy Ratio) You can set the machine to adjust the copy ratio automatically, or to specify the copy ratio for a job. NOTE • If you want to make copies at the copy ratio of 100%, press “Direct.” Enlarging/Reducing Originals to a Standard Size (Preset Zoom) You can enlarge or reduce standard size originals to a standard paper size.
  • Page 36 Place your original, and press “Paper Select.” Select “Auto,” and press “Done.” The display returns to the Basic Features screen. NOTE • The default setting is “Auto.” Press “Copy Ratio.” 1-28 Changing the Copy Ratio (Copy Ratio)
  • Page 37: Specifying The Copy Ratio By % (Zoom Designation)

    To reduce, select a reduction ratio. To enlarge, select an enlargement ratio. Following your selection, press “Done.” The display returns to the Basic Features screen, and the selected copy ratio is displayed. Press (Start). Copying starts. NOTE • To return the copy ratio to 100%, press “Direct.” •...
  • Page 38 Place your original, and press “Copy Ratio.” Set a copy ratio by pressing “–” or “+,” and press “Done.” You can also use (numeric keys) to input the value. Even if you entered the ratio with (numeric keys), you can change the entered values with “–” or “+.” The display returns to the Basic Features screen, and the selected copy ratio is displayed.
  • Page 39: Automatically Setting The Copy Ratio Based On The Original And Copy Paper Sizes (Auto)

    Press (Start). Copying starts. NOTE • To return the copy ratio to 100%, press “Direct.” • To cancel all settings and return the machine to the Standard mode, press (Reset). Automatically Setting the Copy Ratio Based on the Original and Copy Paper Sizes (Auto) The machine automatically selects the appropriate copy ratio based on the size of the original and the selected paper.
  • Page 40 Place your original, and press “Paper Select.” Select the paper size, and press “Done.” The display returns to the Basic Features screen. IMPORTANT • Select a paper size other than “Auto.” If not, the copy ratio will be automatically set to the size of the paper loaded in the top paper drawer.
  • Page 41: Slightly Reducing Images To Prevent The Original From Being Trimmed (Entire Image)

    Press “Auto,” and press “Done.” The specified mode is set and the display returns to the Basic Features screen. Press (Start). Copying starts. NOTE • To return the copy ratio to 100%, press “Direct.” To cancel the setting, press “Copy Ratio” A “Auto” in this order. •...
  • Page 42 Place your originals, and press “Copy Ratio.” Press “Entire Image,” and press “Done.” The specified mode is set and the display returns to the Basic Features screen. Press (Start). Copying starts. NOTE To cancel the setting, press “Copy Ratio” A “Entire Image,” in this order. •...
  • Page 43: Calculating The Copy Ratio Based On The Original And Copy Paper Sizes (Zoom Program)

    Calculating the Copy Ratio Based on the Original and Copy Paper Sizes (Zoom Program) You can change the copy ratio by specifying the original size and paper size in inches. The available copy ratios are from 25% to 800% when the original is placed on the platen glass, and from 25% to 400% when the original is placed in the feeder.
  • Page 44 Making Copies with the Same XY Copy Ratio (Zoom) Place your originals, and press “Copy Ratio.” Press “Other Zoom.” Press “Zoom Program.” 1-36 Changing the Copy Ratio (Copy Ratio)
  • Page 45 Press “Original Size” and enter the original size press “Copy Size” and enter the copy size press “OK.” When entering values in millimeters, you can use (numeric keys) to enter numbers and (Clear) to clear your entries. The display returns to the Basic Features screen, and the specified copy ratio is displayed. If the copy ratio is less than 25%, a message appears telling you that the ratio will be adjusted to 25%.
  • Page 46 Making Copies with Different XY Copy Ratios (XY Zoom) Place your originals, and press “Copy Ratio.” Press “Other Zoom.” Press “Zoom Program.” 1-38 Changing the Copy Ratio (Copy Ratio)
  • Page 47 Press “XY Zoom.” Enter each value for both the original and copy size, after pressing “X” (horizontal direction) and “Y” (vertical direction). Then press “OK.” When entering values in millimeters, you can use (numeric keys) to enter numbers and (Clear) to clear your entries. The display returns to the Basic Features screen, and the selected copy ratio is displayed.
  • Page 48: Enlarging/Reducing Originals With Copy Ratios Set Independently For X And Y Axes (Xy Zoom)

    Press (Start). Copying starts. NOTE • To return the copy ratio to 100%, press “Direct.” To cancel the setting, press “Copy Ratio” A “Other Zoom”A“Zoom Program” A “Cancel,” in • this order. • To cancel all settings and return the machine to the Standard mode, press (Reset).
  • Page 49 ■ Automatically Specifying the Copy Ratio (Auto XY Zoom) The XY copy ratio is automatically set to suit the size of the selected paper. Original Copy LTRR selected LTRR IMPORTANT • You cannot copy highly transparent originals, such as transparencies, in the Auto XY Zoom mode. To make such copies, specify the copy ratio.
  • Page 50 Press “Other Zoom.” Press “XY Zoom.” Enter each value for X and Y after pressing “X” and “Y.” Then press “OK.” You can also use (numeric keys) to input the value. Even if you entered the copy ratio with (numeric keys), you can change the entered values with “–” or “+.” The display returns to the Basic Features screen, and the selected copy ratio is displayed.
  • Page 51 IMPORTANT • When you select “Auto XY Zoom,” you cannot use <Auto> for a paper size. If no paper size is specified, the copy ratio is automatically set to the size of the paper in the top paper drawer. NOTE •...
  • Page 52: Collating Copies (Finisher)

    Collating Copies (Finisher) The Finisher mode can be selected to collate the copies in various ways by pages or copy sets. NOTE • When envelopes, tracing paper, transparencies, or labels are selected, Finisher functions cannot be set. • When heavyweight paper is selected, the Staple or Hole Punch mode cannot be set. Below is a list of finishing functions and paper sizes available for each optional unit.
  • Page 53 ■ When <Collate> Is Set Copies are automatically collated into sets arranged in page order, and output into the trays as follows: Originals Copy set 1 Copy set 2 Copy set 3 Three sets of specified copies ■ When <Group> Is Set All copies of the same original page are automatically collated and grouped together, and output into the trays as follows: Grouped...
  • Page 54 • When you select “Double” (Left) Originals Copy set 1 Copy set 2 Copy set 3 Three sets of specified copies • When you select “Saddle Stitch” Originals Copy set 1 Copy set 2 Copy set 3 Three sets of specified copies IMPORTANT •...
  • Page 55 ■ When <Non-collate> Is Set When neither Collate, Group, nor Staple is set, copies are output into the trays as shown below. Originals Copies ■ When <Hole Punch> Is Set The machine punches 2 or 3 holes in the copies. Originals Copies ■...
  • Page 56: Collating Copies Into Sets In Page Order (Collate)

    ■ When <Offset> Is Set Copies are shifted to the front and back, alternatively. Copies Originals Collating Copies into Sets in Page Order (Collate) Place your originals, and press “Finisher.” NOTE • When Auto Collate is set to “On,” the Offset Collate mode is automatically set when you place the originals in the feeder.
  • Page 57 Press “Collate,” and press “OK.” When Finisher-J1 is attached When Saddle Finisher-G1 and Puncher Unit-K1 are attached, and Tray A exit slot is selected When Saddle Finisher-G1 and When Finisher is not attached, or Puncher Unit-K1 are attached, when only Inner 2way Tray-A1 is and Tray A exit slot is not attached selected...
  • Page 58: Collating Copies Into Groups Of The Same Page (Group)

    - Available paper size is loaded in both horizontal and vertical directions. - Drawer Eligibility for APS/ADS of the paper drawers loaded with available paper size is set to “On.” Â Press (Start). When the original is placed on the platen glass, follow the instructions that appear on the screen and press (Start) once for each original.
  • Page 59 Press “Group,” and press “OK.” When Finisher-J1 is attached When Saddle Finisher-G1 and Puncher Unit-K1 are attached, and Tray A exit slot is selected When Finisher is not attached, or When Saddle Finisher G-1 and when only Inner 2way Tray-A1 is Puncher Unit-K1 are attached, attached and Tray A exit slot is not...
  • Page 60 ● When you select “Rotate” When the Automatic Paper Selection mode is set, press “Next” select LTR, LTRR, STMT, or STMTR-size paper press “OK.” Press “OK,” as long as: - Available paper size is selected manually. - Available paper size is loaded in both horizontal and vertical direction. - Drawer Eligibility for APS/ADS of the paper drawers loaded with the available paper size is set to “On.”...
  • Page 61: Collating Pages And Stapling (Staple)

    Collating Pages and Stapling (Staple) Place your originals, and press “Finisher.” NOTE • When Auto Collate is set to “On,” the Offset Collate mode is automatically set when you place the originals in the feeder. (See ‘Setting Automatic Collate On/Off,’ on p. 3-5.) Press “Staple.”...
  • Page 62 When Saddle Finisher-G1 and Puncher Unit-K1 are attached, and Tray A exit slot is not selected When you want hole punches made, press “Hole Punch.” When the Finisher-J1 is attached, the saddle stitch position cannot be selected. For details of the saddle stitch position, see the Reference Guide. ●...
  • Page 63 - Select the paper size, and press “OK.” NOTE • You can adjust the saddle stitch position. (See the Reference Guide.) Press “OK.” The specified mode is set and the display returns to the Basic Features screen. Press (Start). When the original is placed on the platen glass, follow the instructions that appear in the screen and press (Start) once for each original.
  • Page 64: Two-Sided Copying (Two-Sided Mode)

    Two-sided Copying (Two-sided Mode) This function enables you to make two-sided copies from one- or two-sided originals or one- sided copies from two-sided originals. IMPORTANT • When the machine is operating in the Two-sided Mode, you cannot use the Two-page Separation, Booklet, Transparency Interleaving, Image Combination, or Image Separation modes.
  • Page 65: Making Two-Sided Copies From One-Sided Originals (1 2-Sided)

    Making Two-sided Copies from One-sided Originals (1 2-Sided) This feature enables you to make two-sided copies from one-sided originals. Originals Copy IMPORTANT • Place the originals horizontally when copying originals that are LTRR or STMTR-size. If these originals are placed vertically, the back side of the copies is printed upside down. NOTE •...
  • Page 66 Press “1 2-Sided.” To select the type of two-sided copy: press “Option” A select the type of two-sided original A press “Done.” Press “OK.” The display returns to the Basic Features screen, and <1 2-Sided> is displayed above “Two-sided Mode.” Press (Start).
  • Page 67: Making Two-Sided Copies From Two-Sided Originals (2 2-Sided)

    NOTE To cancel the setting, press “Two-sided Mode” A “Cancel,” in this order. • • To cancel all settings and return the machine to the Standard mode, press (Reset). Making Two-sided Copies from Two-sided Originals (2 2-Sided) This feature enables you to copy two-sided originals on the front and back sides of the paper. Original Copy Place your original, and press “Two-sided Mode.”...
  • Page 68 Press “2 2-Sided.” To select the type of two-sided copy: press “Option” A select the type of two-sided original A press “Done.” Press “OK.” The display returns to the Basic Features screen, and <2 2-Sided> is displayed above “Two-sided Mode.” 1-60 Two-sided Copying (Two-sided Mode)
  • Page 69: Making One-Sided Copies From Two-Sided Originals (2 1-Sided)

    Press (Start). When the original is placed on the platen glass, follow the instructions that appear in the screen and press (Start) once for each original. When scanning is completed, press “Done.” Copying starts. NOTE To cancel the setting, press “Two-sided Mode” A “Cancel,” in this order. •...
  • Page 70 Place your original, and press “Two-sided Mode.” NOTE • When Auto Collate is set to “On,” the Collate mode or the Offset Collate mode is automatically set when you place the original in the feeder. (See ‘Setting Automatic Collate On/Off,’ on p. 3-5.) Press “2 1-Sided.”...
  • Page 71 Press “OK.” The display returns to the Basic Features screen, and <2 1-Sided> is displayed above “Two-sided Mode.” Press (Start). Copying starts. NOTE To cancel the setting, press “Two-sided Mode” A “Cancel,” in this order. • • To cancel all settings and return the machine to the Standard mode, press (Reset).
  • Page 72: Making Two-Sided Copies From Facing Pages In A Book (Book 2-Sided)

    Making Two-sided Copies from Facing Pages in a Book (Book 2-Sided) This feature enables you to make two-sided copies from facing pages or front and back sides of a page in a bound original, such as a book or a magazine. IMPORTANT •...
  • Page 73 Place your original on the platen glass, and press “Two-sided Mode.” If you want to make copies in page order, begin copying from the first page. Place the original face down, so that its top edge is aligned with the top left corner of the platen glass.
  • Page 74 Select the type of two-sided original, and press “OK.” If “Left/Right Two-sided” is selected, the left and right pages of a book or a magazine are copied to the front and back of a single sheet. If you select “Front/Back Two-sided,” the front and back sides of the left page, or the front and back sides of the right page, are copied onto the front and back sides of a single sheet.
  • Page 75: Reserved Copying

    Reserved Copying You can select copy settings and scan originals even if the machine is currently printing. Your scanned documents are processed after the current job is completed. NOTE • You can reserve up to five copy jobs for the Copy function, including the current job. Interrupt copy jobs are not included in this count.
  • Page 76 Press (Start), and start scanning originals. If the following screen is displayed, press “OK.” After the current job is completed, repeat the operation. 1-68 Reserved Copying...
  • Page 77: Interrupting The Current Job To Make Priority Copies (Interrupt Mode)

    Interrupting the Current Job to Make Priority Copies (Interrupt Mode) The Interrupt mode enables you to interrupt the reserved or current job long enough to make higher priority copies. This mode is useful when making a rush copy during a long copy job. NOTE •...
  • Page 78 Once the original is scanned, remove it from the machine. When the Interrupt copy job is completed, the interrupted printing operation resumes. IMPORTANT • If you want to continue making Interrupt copies, wait until the current Interrupt copy job is completed (end of printing).
  • Page 79: Checking A Sample Set Before Copying (Sample Set)

    Checking a Sample Set Before Copying (Sample Set) Before making multiple copies, you can check the copy result using the Sample Set mode. IMPORTANT • “Sample Set” is displayed only when you set to make multiple copies of your original in the Collate, Staple, Cover/Sheet Insertion, or Booklet mode.
  • Page 80 Check the print, and select “Start Print,” “Cancel,” or “Change Settings.” To make the remaining copies, press “Start Print.” To cancel the copying, press “Cancel.” 1-72 Checking a Sample Set Before Copying (Sample Set)
  • Page 81 To change the setting, press “Change Settings,” set a new mode, and press “Done.” - To change the number of copies, use (numeric keys). - To change the exposure, press “Light” or “Dark.” - To make a two-sided copy, press “2-Sided Copy.” - To select the copy paper, press “Paper Select.”...
  • Page 82: Checking The Copy Mode Settings (Setting Confirmation)

    Checking the Copy Mode Settings (Setting Confirmation) When the copy mode settings are selected in screens, for example, the Special Features screen, you can check those settings in a list. Press “Setting Confirmation” in the Basic Features screen. The display shows the selected copy mode settings. Check the settings, and press “Done.”...
  • Page 83: Changing Or Canceling A Selected Copy Mode (Setting Cancel)

    Changing or Canceling a Selected Copy Mode (Setting Cancel) From the Setting Confirmation screen, you can also change or cancel selected functions. Press “Setting Confirmation” in the Basic Features screen. The Setting Confirmation screen is displayed, showing the selected copy mode settings. Press the key of the copy mode to be changed or canceled.
  • Page 84 ● To change a mode (for example, Sharpness) Perform the same steps as when setting the mode. Change the setting as you desire, and press “OK.” The display returns to the Setting Confirmation screen. ● To cancel a mode Press “Cancel.” The display returns to the Setting Confirmation screen.
  • Page 85: Useful Copy Functions

    Useful Copy Functions CHAPTER This chapter describes more advanced copy functions. Copying Facing Pages in a Book on Two Separate Sheets of Paper (Two-page Separation) ........... 2-3 Adding Front and Back Covers, Sheet Insertions and Chapter Pages to Copy Sets (Cover/Sheet Insertion).
  • Page 86 2. Useful Copy Functions Making Sharp Contrast Copies (Sharpness) ....... . .2-64...
  • Page 87: Copying Facing Pages In A Book On Two Separate Sheets Of Paper (Two

    Copying Facing Pages in a Book on Two Separate Sheets of Paper (Two-page Separation) This mode enables you to copy facing pages in a book or a magazine onto separate sheets of paper. Copy Original IMPORTANT • When the machine is operating in the Two-page Separation mode, you cannot use the Two-sided, Cover/Sheet Insertion, Booklet, Transparency Interleaving, Binding Erase, Different Size Originals, Image Combination, Image Separation, or Image Repeat modes.
  • Page 88 Press “Done.” The specified mode is set and the display returns to the Basic Features screen. Press (Start). Copying starts. NOTE To cancel the setting, press “Special Features” A “Two-page Separation” A “Done,” in this • order. • To cancel all settings and return the machine to the Standard mode, press (Reset).
  • Page 89: Adding Front And Back Covers, Sheet Insertions And Chapter Pages To Copy Sets (Cover/Sheet Insertion)

    Adding Front and Back Covers, Sheet Insertions and Chapter Pages to Copy Sets (Cover/Sheet Insertion) This function enables you to set the machine to automatically add front and back covers, sheet insertions, or chapter pages using a different type of paper from which is used for the main text.
  • Page 90 ■ Back Cover Adds a back cover sheet to each set of copies. The back cover can also be copied on. Original Copies R E P O R T R E P O R T Printed back cover selected in the Cover/Sheet Insertion mode ■...
  • Page 91 ■ Chapter Page Adds chapter pages between the pages of copy sets. Since the chapter page is always copied on one side, this function is useful when you want to divide the copy by chapter. Original Copies R E P O R T R E P O R T Printed chapter page selected in the Cover/Sheet Insertion mode Place your originals, and press “Special Features”...
  • Page 92 When copying onto the front cover, back cover, or sheet insertion, press “Printed,” and press “Next.” When setting Two-sided Copying, press “Option,” set the side to be copied, and press “Done.” NOTE • The display varies depending on the setting in step 2. •...
  • Page 93 ● When you select “Back Cover”: Select the side to be copied onto, and press “Next.” ● When you select “Sheet Insertion” or “Chapter Page”: Set all positions where the sheet is to be inserted into the copies, and press “Next.”...
  • Page 94 Select the paper source for each cover/sheet insertion press “OK” press “Done.” The specified mode is set and the display returns to the Basic Features screen. IMPORTANT • Select the same paper size for the front and back cover, sheet insertions, and chapter page.
  • Page 95: Making Copies For Use As A Booklet (Booklet)

    Making Copies for Use as a Booklet (Booklet) You can copy one-sided or two-sided originals in such a way that the copies are made into a booklet. Originals Copies When the Saddle Finisher-G1 is attached IMPORTANT • When the machine is operating in the Booklet mode, you cannot use the Entire Image, Finisher, Two-sided, Two-page Separation, Cover/Sheet Insertion, Transparency Interleaving, Margin, Frame Erase, Different Size Originals, Image Combination, Image Separation, Image Repeat, or Mirror Image modes.
  • Page 96: Making Copies For Use As A Booklet (Booklet)

    Select the original size, and press “Next.” If two-sided originals will be copied, also press “2-Sided Original” to select how the two- sided originals are to be saddle stitched, and press “OK.” NOTE • To select an A or B series paper size, press “A/B-size.” Select the paper size, and press “Next.”...
  • Page 97 NOTE • Set the cover paper face down in the stack bypass. ● When you select “Add Cover”: Select “Yes” or “No” to specify whether or not to copy on the cover, and press “Next.” Select the type of paper, and press “Next.” IMPORTANT •...
  • Page 98 Select whether to saddle stitch the booklet, and press “OK” press “Done.” The specified mode is set and the display returns to the Basic Features screen. NOTE • When the number of sheets exceeds 11, stapling is not performed, and the sheets are output to the tray.
  • Page 99: Making Copies With Sheets Of Paper Interleaved Between Transparencies (Transparency Interleaving)

    Making Copies with Sheets of Paper Interleaved Between Transparencies (Transparency Interleaving) Use this mode when copying onto transparencies fed from the stack bypass. The machine automatically interleaves a sheet of paper between each transparency. The interleaf sheets protect the copied surface of the transparencies. The image can also be printed on the interleaf sheets.
  • Page 100 ■ When Printing on the Interleaf Sheets: Outputs a printed transparency and a printed interleaf sheet alternately. Copies Originals Transparencies R E P O R T R E P O R T R E P O R T Printed interleaf sheets Place your original, and press “Special Features”...
  • Page 101 Select the size of the interleaf sheet, and press “Next.” Select whether or not to copy the image onto the interleaf sheet, and press “OK” press “Done.” The selected mode is set and the display returns to the Basic Features screen. NOTE •...
  • Page 102 Place the transparencies in the stack bypass, and press (Start). Scanning starts. When the original is placed on the platen glass, follow the instructions that appear on the display and press (Start) once for each original. When scanning is completed, press “Done.”...
  • Page 103: Making Copies With Original Image Shifted (Shift)

    Making Copies with Original Image Shifted (Shift) Makes copies with the entire image shifted to the center or a corner. IMPORTANT • When the machine is operating in the Shift mode, you cannot use the Image Repeat or Mirror Image modes. •...
  • Page 104: Makes Copies With Original Image Shifted To The Center Or A Corner2-20

    Makes Copies with Original Image Shifted to the Center or a Corner Place your original, and press “Special Features” press “Shift.” Press “Center Shift/Corner Shift,” and select the shift direction with an arrow key. Then press “OK,” and “Done.” The shift direction refers not to the direction in which the original is placed on the platen glass or in the feeder, but to the direction that you want the original image shifted (viewing the original that you want to scan as face up and situated in the center of the copy page).
  • Page 105: Makes Copies With Original Image Shifted Using The Numeric Keys

    Makes Copies with Original Image Shifted Using the Numeric Keys Place your original, and press “Special Features” press “Shift.” Press “No. Key Entry” to select the shift direction, enter the desired value using (numeric keys). If you enter a value outside the setting range, a message prompting you to enter an appropriate value appears in the screen.
  • Page 106 ● Example: To move the image in a diagonal direction as in the illustration below: Press the upper or lower side “ ” to enter the value. Next, press the right or left side “ .” Enter the value on the touch panel display, and press “OK” press “OK.”...
  • Page 107: Making Copies With Margins (Margin)

    Making Copies with Margins (Margin) This mode enables you to make copies with the entire original image shifted by a designated width to the left, right, top, or bottom to create a margin on the copies. Use this mode to make copies ready for placement in ring binders.
  • Page 108 Place your original, and press “Special Features” press “Margin.” Select the type of margin, and press Next. “ ” IMPORTANT • If you are using the Margin and Two-sided modes together and copying an original that already has a left or right margin, follow the instructions below: - 1 2-sided: Set the margin for the back only.
  • Page 109 ● When you select “Left Margin” or “Right Margin”: Use “–” or “+” to set the margin for the front and back (0" to 13/16" or 0 to 20mm). Then press “OK,” and press “Done.” The specified mode is set and the screen returns to the Basic Features screen. ●...
  • Page 110: Erasing Shadows And Frame Lines From Copies (Frame Erase)

    Erasing Shadows and Frame Lines from Copies (Frame Erase) This mode erases shadows and lines that appear when copying various types of originals. IMPORTANT • Combination of the Original Frame Erase, Book Frame Erase, or Binding Erase modes cannot be set.
  • Page 111 ■ Book Frame Erase Erases the dark border as well as center and contour lines that appear when copying facing pages in a bound original onto a single sheet of paper. Copy Book Frame Erase Original selected Copy Book Frame Erase not selected IMPORTANT...
  • Page 112: Making Copies Erasing The Frame Of The Originals (Original Frame Erase)

    Making Copies Erasing the Frame of the Originals (Original Frame Erase) Place your originals, and press “Special Features” press “Frame Erase.” Press “Original Frame Erase,” and press “Next.” Select the size of the original, and press “Next.” IMPORTANT • You can set the Original Frame Erase mode only on the original sizes shown on the touch panel display.
  • Page 113 Select the desired original frame erase width using “-” or “+,” and press “OK” press “Done.” When entering values in millimeters, you can use (numeric keys) and (Clear). Even when you enter the values with (numeric keys), you can change the values with “–”...
  • Page 114: Making Copies Erasing The Book Frame (Book Frame Erase)

    Press (Start). Copying starts. NOTE To cancel the setting, press “Special Features” A “Frame Erase” A “Cancel,” in this order. • • To cancel all settings and return the machine to the Standard mode, press (Reset). Making Copies Erasing the Book Frame (Book Frame Erase) Place your original, and press “Special Features”...
  • Page 115 Press each key: “Top,” “Left,” “Center,” “Right,” and “Bottom” the desired book frame erase width using “-” or “+” press “OK” “Done.” When entering values in millimeters, you can use (numeric keys) and (Clear). Even when you enter the values with (numeric keys), you can change the values using “–”...
  • Page 116: Making Copies Erasing Binding Holes Etc. (Binding Erase)

    Press (Start). Copying starts. NOTE To cancel the setting, press “Special Features” A “Frame Erase” A “Cancel,” in this order. • • To cancel all settings and return the machine to the Standard mode, press (Reset). Making Copies Erasing Binding Holes etc. (Binding Erase) Place your original on the platen glass, and press “Special Features”...
  • Page 117 The position of the binding holes refers not to the position in which the original is placed on the platen glass, but to the position of the binding holes viewed when the surface of the original that you want to scan is face up, with its top edge aligned with the top left corner of the platen glass.
  • Page 118: Reducing Two, Four, Or Eight Originals To Fit On A Single Copy Sheet (Image Combination)

    Reducing Two, Four, or Eight Originals to Fit on a Single Copy Sheet (Image Combination) This mode automatically reduces two, four, or eight originals, two-sided originals, or the facing pages of a book to fit on one side or both sides of a selected paper size. IMPORTANT •...
  • Page 119 ■ 4 On 1 Reduces four 1-sided or two 2-sided originals to fit on one side or both sides of the copy sheet. Originals Copy ■ 8 On 1 Reduces eight 1-sided or four 2-sided originals to fit on one side or both sides of the copy sheet.
  • Page 120 Place your originals, and press “Special Features” press “Image Combination.” NOTE • When Auto Collate is set to “On,” the Collate mode or the Offset Collate mode is automatically set when you place the originals in the feeder. (See ‘Setting Automatic Collate On/Off,’...
  • Page 121 Select the desired Image Combination feature, and press “Next.” If you want to make two-sided copies, press “2-Sided Copy,” select the opening method, and press “OK.” Press “Option” to select the order of the image layout, and press “Done.” 2 On 1 4 On 1, 8 On 1 If you do not specify “Option,”...
  • Page 122 Select the paper size, and press “OK” press “Done.” The specified mode is set and the display returns to the Basic Features screen. IMPORTANT • You cannot set Automatic Paper Selection in the Image Combination mode. NOTE • The machine automatically selects the copy ratio depending on the selected paper size. •...
  • Page 123: Dividing An Original Into Equal Sections And Enlarging Each Section On A Separate Copy Sheet (Image Separation)

    Dividing an Original into Equal Sections and Enlarging Each Section on a Separate Copy Sheet (Image Separation) This mode automatically divides an original into equal sections and copies each section in an enlarged form on a separate sheet of paper. The following four types of Image Separation features are available: 1 to 2 (1-sided and 2- sided copies), and 1 to 4 (1-sided and 2-sided copies).
  • Page 124 ■ 1 to 4 Divides a one-sided original into four equal sections and outputs the sections in an enlarged form as four 1-sided copies or two 2-sided copies. Original Copies NOTE • You can place LTR-size originals horizontally or vertically when using this feature. Place the original on the platen glass, and press “Special Features”...
  • Page 125 If “2-Sided Copy” is selected, select the opening method, and press “OK.” Select the layout of the final page of the original, and press “Next.” 1 To 2 1 To 4 You can reduce the output of pages without images (blank output) by setting the layout of the last original.
  • Page 126 Select the paper size, and press “OK” press “Done.” The specified mode is set and the display returns to the Basic Features screen. IMPORTANT • You cannot select “Automatic Paper Selection” in the Image Separation mode. NOTE • The machine automatically selects the copy ratio depending on the selected paper size. Press (Start).
  • Page 127: Feeding Different-Size Originals Together In The Feeder (Different Size Originals)

    Feeding Different-size Originals Together in the Feeder (Different Size Originals) This function enables you to copy different-size originals together in one group, by setting them in the feeder. IMPORTANT • This function can be set when the Feeder (DADF-H1) is attached. •...
  • Page 128 Select the type of Different Size Originals mode, and press “OK” press “Done.” When you are setting originals of the same width, press “Same Width.” When you are setting originals of different widths, press “Different Width.” The selected mode is set and the display returns to the Basic Features screen. Press (Start).
  • Page 129: Copying Separately-Set Originals (Job Build)

    Copying Separately-set Originals (Job Build) This mode enables you to scan too many originals to set at once, by dividing them into multiple batches. You can use both the feeder and the platen glass for scanning. The originals are copied as one document after all batches have been scanned. Originals Copies IMPORTANT...
  • Page 130 Press “Job Build,” and press “Done.” The specified mode is set and the display returns to the Basic Features screen. Press (Start). Scanning starts. NOTE • To cancel scanning, press “Cancel” or (Stop). When scanning is completed, place the next original, and press (Start).
  • Page 131 When scanning two-sided originals, press “2-sided Original.” Select the type of two-sided original, and press “OK.” - Do not forget to set or cancel the Two-sided Original mode according to the type of originals. Repeat this operation as necessary. After the last original is scanned, press “Done.” NOTE To cancel the setting, press “Special Features”...
  • Page 132: Storing/Recalling Often-Used Copy Settings In Memory (Mode Memory)

    Storing/Recalling Often-used Copy Settings in Memory (Mode Memory) You can store any possible combination of the Copy functions, up to nine settings, in a memory key, and then name that key. It is useful when you want to store frequently used Copy functions.
  • Page 133 Press “Mode Memory.” Press “Store/Erase.” Press “Store.” Storing/Recalling Often-used Copy Settings in Memory (Mode Memory) 2-49...
  • Page 134: Storing Copy Settings

    Select the desired memory key from among memory keys “M1” to “M9,” and press “Next.” NOTE ■ • A mode memory key already storing copy settings shows a small, black square ( ) in the lower right corner. • If you select a memory key already storing copy settings, the settings are displayed. •...
  • Page 135: Storing A Memory Key Name

    ● If you select a memory key already storing a copy setting: Select “Yes” to overwrite the stored settings. Select “No” to cancel storing. When storing is completed, the message <Stored in memory.> appears for about two seconds. The memory key storing the copy settings is reversed and the stored settings are displayed. Press “OK,”...
  • Page 136 Press “Store Name.” Select the memory key (“M1” to “M9”) to which you want to store a name, and press “Next.” NOTE ■ • A mode memory key already storing copy settings shows a small, black square ( ) in the lower right corner.
  • Page 137 Enter the new name, and press “OK.” The maximum number of characters you can use for the memory key name is 10. For details of how to enter characters from the touch panel display, see the Reference Guide. The name appears on the memory key. NOTE •...
  • Page 138: Recalling Copy Settings

    Recalling Copy Settings Press “Special Features,” and press “Mode Memory.” Select the memory key storing the copy settings you want to use confirm the stored settings press “OK” press “Done.” The display returns to the Basic Features screen. NOTE • Recalling copy settings from memory cancels the current copy settings.
  • Page 139 Press “Erase.” Select a memory key to be erased, and press “Next.” The message appears to confirm that you want to erase the copy job. IMPORTANT • Check the copy settings before you erase them. NOTE ■ • A mode memory key already storing copy settings shows a small, black square ( ) in the lower right corner.
  • Page 140 Press “Yes.” If you want to cancel erasing, press “No.” The message <Erased.> appears for about two seconds on the touch panel display. The stored copy setting is erased. NOTE • The name of the memory key is not erased. For details of how to change the name, see ‘Storing a Memory Key Name,’...
  • Page 141: Recalling A Previous Copy Setting (Recall)

    Recalling a Previous Copy Setting (Recall) With this function, you can recall up to three previous copy settings and make copies using these settings. IMPORTANT • One copy job is defined by setting the number of copies, exposure, copy ratio, etc., and pressing (Start) or (Reset) when the Auto Clear function is “On”, or by calling up a copy job stored in memory.
  • Page 142: Inverting Original Images (Nega/Posi)

    Inverting Original Images (Nega/Posi) This function enables you to make copies of the original image inverting the black and the white areas. Copy Original SCENE SCENE ▼ Place your originals, and press “Special Features” press “ .” Press “Nega/Posi,” and press “Done.” The specified mode is set and the display returns to the Basic Features screen.
  • Page 143: Making Copies With The Original Image Repeated (Image Repeat)

    Making Copies with the Original Image Repeated (Image Repeat) You can repeatedly copy the image of an original in either the vertical or horizontal direction. The following two setting methods are available for the Image Repeat mode. ■ Automatic Setting The original image is copied so that the maximum possible number of copies fit in the selected paper size.
  • Page 144 ■ Manual Setting The original image is copied a specified number of times. Copy Original CITY CITY CITY CITY Example: When <3 times> is specified, images overlap when copied. IMPORTANT • When the machine is operating in the Image Repeat (manual setting) mode, you cannot use the Entire Image, Book 2-Sided, Two-page Separation, Cover/Sheet Insertion, Shift, Booklet, Transparency Interleaving, Margin, Frame Erase, Different Size Originals, Image Combination, Image Separation, or Mirror Image modes.
  • Page 145: Manual Setting

    ● Manual setting Press “–” or “+” to set the number of images. The number of times the image can be repeated is from 1 to 20. IMPORTANT • Depending on how many times you have manually set the image to be repeated, some of the designated images may overlap.
  • Page 146: Making Copies With Image Reversed (Mirror Image)

    Making Copies with Image Reversed (Mirror Image) This mode copies the image of the original reversed as a reflection in the mirror. Copy Original IMPORTANT • When the machine is operating in the Mirror Image mode, you cannot use the Entire Image, Cover/Sheet Insertion, Shift, Booklet, Margin, Frame Erase, Image Combination, Transparency Interleaving, or Image Repeat modes.
  • Page 147 Press (Start). Copying starts. NOTE ▼ To cancel the setting, press “Special Features” A “ ” A “Mirror Image,” in this order. • • To cancel all settings and return the machine to the Standard mode, press (Reset). Making Copies with Image Reversed (Mirror Image) 2-63...
  • Page 148: Making Sharp Contrast Copies (Sharpness)

    Making Sharp Contrast Copies (Sharpness) This mode allows you to make copies of original images with the contrast reproduced more sharply or more softly. To make copies with text or lines reproduced more sharply, use “High.” To make copies with photographs or other halftones reproduced more softly, use “Low.” ■...
  • Page 149: Making Sharp Contrast Copies (Sharpness)

    ▼ Place your original, and press “Special Features” press “ ” press “Sharpness.” Adjust the sharpness by pressing “Low” or “High,” and press “OK” press “Done.” To copy text and lines clearly, the setting should be towards “High.” To copy halftone images such as photographs, the setting should be towards “Low.”...
  • Page 151 Setting/Storing Specifications of the Copy Function CHAPTER This chapter describes how to store or change the default settings to suit your needs. Copy Settings List............3-2 Setting Standard Keys .
  • Page 152: Copy Settings List

    Copy Settings List The following items can be stored or set in the Copy Settings screen. Additional Function Available settings Applicable page Copy Settings Standard Key 1, 2 Settings All modes (No setting*) p. 3-3 Auto Collate On*/Off p. 3-5 Image Orientation Priority On/Off* p.
  • Page 153: Setting Standard Keys

    Setting Standard Keys You can store up to two Standard keys from the Copy Ratio, Finisher, and Two-sided Mode keys on the Basic Features screen, the keys on the Special Features screen, or the memory keys containing copy settings stored in Mode Memory. This is useful when you want to store the frequently-used copy functions in the Basic Features screen.
  • Page 154 Select the desired modes to be stored with the Standard key, and press “OK.” NOTE • To cancel storing, press “Cancel.” Press “Done.” Repeat this procedure. The display returns to the Basic Features screen. Example: The stored Standard keys are displayed as shown below. Standard key 1 Standard key 2 Setting Standard Keys...
  • Page 155: Setting Automatic Collate On/Off

    Setting Automatic Collate On/Off This mode allows automatic selection of the Collate (Offset Collate) mode when the original is placed in the feeder. This is helpful when making multiple copies, because you do not need to remember to select the Finisher mode. IMPORTANT •...
  • Page 156: Setting Image Orientation Priority To On/Off

    Setting Image Orientation Priority to On/Off The image orientation may be printed conversely depending on the copy mode set. With this function, you can set whether or not to copy the image in the same direction as the original image. IMPORTANT •...
  • Page 157: Setting The Job Duration Display

    Setting the Job Duration Display When Job Duration Display is set to “On,” the time remaining until completion of the copy job (Job Duration Time) is indicated in minutes on the touch panel display. NOTE • The job duration time is not displayed for the Transparency Interleaving, Cover/Sheet Insertion, Different Size Originals, Rotate Collating, and Rotate Grouping modes or when the copy waiting time is less than one minute.
  • Page 158: Setting Auto Orientation To On/Off

    Setting Auto Orientation to On/Off Using parameters such as original size and zoom ratio, this function automatically rotates the image to the most suitable position for the specified paper size. NOTE • The default setting is “On.” Call up the desired screen as follows: (Additional Functions) Select “On”...
  • Page 159: Setting The Photo Mode Of The Copy Function

    Setting the Photo Mode of the Copy Function You can set whether or not to use the Photo mode in the Copy function. When the Photo Mode is “On,” you can select “Printed Image” and “Photo” when making copies with the image quality setting.
  • Page 160: Changing The Current Standard Settings

    Changing the Current Standard Settings Standard Settings refers to a combination of Copy modes that the machine automatically sets after the power is turned on or when (Reset) is pressed. The Standard Settings can be changed to suit your needs, or be returned to the default settings. NOTE •...
  • Page 161: Initializing The Standard Settings

    Press “Yes.” To cancel storing the currently displayed settings as the Standard Settings, press “No.” This screen is displayed for about two seconds as the settings currently displayed are stored as the Standard Settings. NOTE ▲ ▼ • The settings displayed here are the currently set copy settings. Press “ ”...
  • Page 162 Press “Initialize.” Check the setting, and press “Yes.” To cancel the initialization, press “No.” This screen is displayed for about two seconds as the Standard Settings are initialized. Press “Done.” Repeat this procedure. The display returns to the Basic Features screen. 3-12 Changing the Current Standard Settings...
  • Page 163: Restoring Settings To Default Copy Settings

    Restoring Settings to Default Copy Settings Items that have been changed in the Copy Settings can be returned to their default settings. Call up the desired screen as follows: (Additional Functions) Press “Yes.” To cancel the initialization of copy settings, press “No.” The display returns to the Copy Setting screen.
  • Page 165: Chapter 4 Appendix

    Appendix CHAPTER Chart of Available Combination of Functions ........4-2 Index .
  • Page 166: Chart Of Available Combination Of Functions

    Chart of Available Combination of Functions The chart shows the settings combinations when you want to reconfigure the functions. Combination available ✕ Combination unavailable ▲ Priority to latest set mode ● Priority to Image Combination, Image Separation, and Booklet modes (Ratio can be changed) Function intend to set ▲...
  • Page 167 Combination available ✕ Combination unavailable ▲ Priority to latest set mode ● Priority to Image Combination, Image Separation, and Booklet modes (Ratio can be changed) Function intend to set ✕ ✕ ✕ ✕ ✕ Two-page Separation ● ● ● ● ✕...
  • Page 168 Combination available ✕ Combination unavailable ▲ Priority to latest set mode ● Priority to Image Combination, Image Separation, and Booklet modes (Ratio can be changed) Function intend to set ● ● ● ● ● Enlargement ● ● ● ● ● Zoom Designation ●...
  • Page 169 Combination available ✕ Combination unavailable ▲ Priority to latest set mode ● Priority to Image Combination, Image Separation, and Booklet modes (Ratio can be changed) Function intend to set ✕ ✕ ✕ ✕ ✕ ✕ ✕ ✕ ✕ ✕ ✕ ✕...
  • Page 170: Index

    Index 1 to 2 ............................2-39 1 to 4 ............................2-40 1 2-Sided ........................1-56 1-57 2 On 1 ............................2-34 2 1-Sided ........................1-56 1-61 2 2-Sided ........................1-56 1-59 4 On 1 ............................2-35 8 On 1 ............................2-35 Auto ............................
  • Page 171 Different Size Originals ......................2-43 Direct ............................1-27 Entire Image ..........................1-33 Finisher ............................. 1-44 Frame Erase ..........................2-26 Front Cover ..........................2-5 Front/Back Two-sided ........................ 1-64 Group ..........................1-45 1-50 Hole Punch ..........................1-47 Image Combination ........................2-34 Image Orientation Priority ......................3-6 Image Repeat ...........................
  • Page 172 Left/Right Two-sided ........................1-64 Manual Paper Selection ......................1-19 Margin ............................2-23 Mirror Image ..........................2-62 Mode Memory ........................... 2-48 Nega/Posi ..........................2-58 Non-collate ..........................1-47 Offset ............................1-48 Original Frame Erase ...................... 2-26 2-28 Paper Select ..........................1-17 Photo Mode ........................1-23 Preset Zoom ..........................
  • Page 173 Shift ............................2-19 Special Features Screen 1/2 ...................... 1-5 Special Features Screen 2/2 ...................... 1-8 Standard Keys ..........................3-3 Standard Settings ........................3-10 Staple ..........................1-45 1-53 Text Mode ..........................1-23 Text/Photo Mode ........................1-23 Transparency Interleaving ......................2-15 Two-page Separation ........................2-3 Two-sided Mode ........................
  • Page 174 100% recycled paper. CANON INC. 30-2, Shimomaruko 3-chome, Ohta-ku, Tokyo 146-8501, Japan CANON U.S.A., INC. One Canon Plaza, Lake Success, NY 11042, U.S.A. CANON CANADA INC. 6390 Dixie Road Mississauga, Ontario L5T 1P7, Canada CANON EUROPA N.V. Bovenkerkerweg 59-61 P.O. Box 2262, 1180 EG Amstelveen, The Netherlands CANON FRANCE S.A.

This manual is also suitable for:

Imagerunner 2800 seriesImagerunner 2200 series

Table of Contents