Honeywell Lynx Plus Series Installation And Setup Manual page 32

Lynx Plus Series Installation and Setup Guide
Data Field Descriptions
61 61 61 61
BYPASS REP BYPASS BYPASS BYPASS REP COD REP REP COD CODE E E E COD
62 62 62 62
AC AC AC AC LOSS LOSS REP REP CODE CODE
LOSS LOSS REP REP CODE CODE
63 63 63 63
LOW BAT LOW BAT REP REP CODE CODE
LOW LOW BAT BAT REP REP CODE CODE
64 64 64 64
TEST REP TEST TEST TEST REPORT REP REP ORT ORT CODE ORT CODE CODE CODE
65 65 65 65
OPEN REP OPEN REPORT ORT CODE CODE
OPEN OPEN REP REP ORT ORT CODE CODE
66 66 66 66
AWAY/STAY AWAY STAY REP REP ORT ORT
AWAY AWAY STAY STAY REP REP ORT ORT
67 67 67 67
RF RF RF RF TRANS TRANS TRANS TRANS LB LB LB LB REP REP REP REP
LynxSIA Plus Only - The control validates the data entered in fields ✻68-69. If the selection is not
Field ✻ 68-69:
valid the control will emit a single long beep indicating that the selection has been rejected. The control replaces the
selection with the default value, which is displayed on the keypad, and advances to the next field. Field ✻68 & ✻69 are
always enabled however, a report code can be entered if reporting formats other than Contact ID ® are used
68 68 68 68
CANCEL REP CANCEL CANCEL CANCEL REP REP REP CODE CODE CODE CODE
69 69 69 69
RECENT CLOS RECENT RECENT RECENT CLOS CLOS REP CLOS REP REP REP
This field applies only to the
(
LynxSIA Plus control)
RESTORE REPORT CODES (
70 70 70 70
ALARM RES ALARM RES REPORT REPORT
ALARM ALARM RES RES REPORT REPORT
71 71 71 71
TROUBLE RES TROUBLE TROUBLE TROUBLE RES RES REP RES REP REP REP
72 72 72 72
BYPASS RES BYPASS RES REP REP
BYPASS BYPASS RES RES REP REP
Bypass Report Code
(See notes above)
A Bypass Report will be sent when a zone is manually bypassed.
AC Loss Report Code
Timing of the AC Loss Report is random with up to a 4-hour delay. If AC restores before
the report goes out, there is no AC restore report.
Low Battery Report Code
Low Battery Report will be sent when a low battery condition exists in the system's
standby battery.
Test Report Code
(See notes above)
Test Report is sent periodically to test that the communicator and phone lines are
operational (frequency of report is selected in field ✻51).
Note: The LynxSIA Plus control validates the data entered in this field. If the selection is not
valid the control will emit a single long beep indicating that the selection has been
rejected. The control replaces the selection with the default value "10", which is
displayed on the keypad, and advances to the next field.
Opening Report Code
This report is sent upon disarming of the system. If expanded or 4+2 reporting is
selected, the 2nd digit = user number.
Arm Away Report Code
This option allows for independent programming of Away and Stay reports. If expanded
or 4+2 reporting is selected, the 2nd digit = user number.
Note: OPEN reports are not sent if the associated closing report is not enabled.
RF Transmitter Low Battery Report Code
This report is sent in the event that a wireless transmitter low battery condition exists.
Cancel Report Code
(See notes above)
This report is sent upon disarming of the system after an alarm condition was reported.
Recent Closing Report Code
Recent Closing Report is sent when an alarm occurs within two minutes after exit
delay expires. Disarming the system within the two minutes stops the alarm sound and
the keypad displays the faulted zone number and "CA" if the cancel display option was
enabled in field *57. No messages are sent to the Central Station.
If the system is not disarmed within two minutes, the alarm sound continues and a
"Recent Closing" and a "Zone Alarm" message are sent to the Central Station (after dial
delay expires).
✻ ✻
70– 76)
Alarm Restore Report Code
1st digit is sent when the zone that caused an alarm is restored to its non-faulted
condition. If expanded or 4+2 reporting is selected, 2nd digit is automatically sent as
the 2nd digit of the zone alarm report code programmed in field ✻ 56.
Trouble Restore Report Code
Report is sent when a trouble in a zone is restored.
Bypass Restore Report Code
Report is sent when a zone that has been bypassed is unbypassed.
(See notes above)
(See notes above)
(See notes above)
(See notes above)
(See notes above)
(This field applies only to the LynxSIA Plus control)
(See notes above)
(See notes above)
(See notes above)
- 32 -