Cv-A11 Rs-232C Command List - JAI CV-A11 Operation Manual

7.2. CV-A11 RS-232C command list.

Command Name
A – General settings and useful commands
EB Echo Back
ST Camera Status request
HP Online Help request
VN Firmware version
B – Timing and shutter related commands
SC Scanning format
TR Trigger mode
SM Shutter mode
SH Shutter speed
PE Programmable expos.
HC HD accumulation
C – Signals and polarity
SO Sync signal
CW Clock/WEN
TP Trigger polarity
WP WEN polarity
D – Gain and analogue signals setting
AS AGC Switch
AG AGC Level
GA Manual gain Level
RP Rear Potentiometer
SU Setup Level
WC White clip Level
GS Gamma Select
E – Saving and loading data in EEPROM
LD Load settings from
camera EEPROM
SA Save settings to
camera EEPROM
*1) PE=0 has no function in triggered mode. PE=1 is 0.5H in continuous mode
*2) If positive logic is used (TP=1), the first trigger pulse after power up will be ignored.
!! Do not try to use commands not shown in the list.
CV-A11
Format
EB=[Param.]<CR><LF>
ST?<CR><LF>
HP?<CR><LF>
VN?<CR><LF>
SC=[Param.]<CR><LF>
TR=[Param.]<CR><LF>
SM=[Param.]<CR><LF>
SH=[Param.]<CR><LF>
PE=[Param.]<CR><LF>
HC=[Param.]<CR><LF>
SO=[Param.]<CR><LF>
CW=[Param.]<CR><LF>
TP=[Param.]<CR><LF>
WP=[Param.]<CR><LF>
AS=[Param.]<CR><LF>
AG=[Param.]<CR><LF>
GA=[Param.]<CR><LF>
RP=[Param.]<CR><LF>
SU=[Param.]<CR><LF>
WC=[Param.]<CR><LF>
GS=[Param.]<CR><LF>
LD=[Param.]<CR><LF>
SA=[Param.]<CR><LF>
- 18 -
Parameter
0=Echo off 1=Echo on
0=full frame 1=1/2 partial
2=1/3 partial 3=1/6 partial
0=normal 1=Edge
2=Pulse width 3=Frame delay
4=Long time 5=Start/stop
6=Smearless
0=Normal 1=Programmab.
0=1/30 1=1/50
2=1/60 3=1/125
4=1/250 5=1/500
6=1/1000 7=1/2000
8=1/4000 9=1/10,000
10=1/20,000 11=1/40,000
12=1/60,000 13=1/80,000
14=1/100,000
1=1.5H 1023=1023.5 H
0=*1),
0=H synchron 1=a-synchron
accumulation accumulation
0=no sync 1=sync on video
0= WEN out 1=Clock out
0= active low 1= active high
0= active low 1= active high
0=AGC off 1=AGC on
0=low 255=high
0=low 255=high
0=manual gain 1=rear potm.
0=low 255=high
0=low 255=high
0=gamma 1 1=gamma 0.45
0=Factory data 1=User 1 area
2=User 2 area 3=User 3 area
1=User 1 area 2=User 2 area
3=User 3 area
Remarks
Off at power up
Actual setting
Command list
3 letter version
All15 step is valid
in normal trigger
mode.
In all trigger
modes shutter
speeds higher
than 9 will result
in 1/10,000
H= 63.56µsec
a-sync. only for
TR=2 and TR=3
CW=0 if clock not
used
*2)
0= manual gain
Range 0 to 255
Range 0 to 255
Range 0 to 255
Range 0 to 255
Latest used data
area becomes
default at next
power up