Cv-A50/60 Rs-232C Command List - JAI CV-A50 Operation Manual

7.2. CV-A50/60 RS-232C command list.

Command Name
A – General settings and useful commands
EB Echo Back
ST Camera Status request
HP Online Help request
VN Firmware version
B – Timing and shutter related commands
SC Scanning format
TR Trigger mode
SM Shutter mode
SH Shutter speed
PE Programmable expos.
C – Signals and polarity
FR Accumulation
PC Pixel clock
TP Trigger polarity
WP WEN polarity
D – Gain and analogue signals setting
AS AGC Switch
AG AGC Level
GA Manual gain Level
RP Rear Potentiometer
SU Setup Level
WC White clip Level
GS Gamma Select
E – Saving and loading data in EEPROM
LD Load settings from
camera EEPROM
SA Save settings to
camera EEPROM
*1) In normal non trigger mode (TR=0) PE<312 for CCIR and PE<262 for EIA. In trigger mode TR=1, EEN will not be correct if
PE>833.
*2) If positive logic is used (TP=1), the first trigger pulse after power up will be ignored.
!! Do not try to use commands not shown in the list.
CV-A50 / CV-A60
Format
EB=[Param.]<CR><LF>
ST?<CR><LF>
HP?<CR><LF>
VN?<CR><LF>
SC=[Param.]<CR><LF>
TR=[Param.]<CR><LF>
SM=[Param.]<CR><LF>
SH=[Param.]<CR><LF>
PE=[Param.]<CR><LF>
FR=[Param.]<CR><LF>
PC=[Param.]<CR><LF>
TP=[Param.]<CR><LF>
WP=[Param.]<CR><LF>
AS=[Param.]<CR><LF>
AG=[Param.]<CR><LF>
GA=[Param.]<CR><LF>
RP=[Param.]<CR><LF>
SU=[Param.]<CR><LF>
WC=[Param.]<CR><LF>
GS=[Param.]<CR><LF>
LD=[Param.]<CR><LF>
SA=[Param.]<CR><LF>
- 19 -
Parameter
0=Echo off 1=Echo on
0=Interlaced 1=Non-interl.
2=1/2 partial 3=1/3 partial
0=normal 1=Edge
2=Pulse width 3=Frame delay
4=Long time 5=Start/stop
0=Normal 1=Programmab.
0=Off 1=1/100
0=1/50 (1/60) 1=1/125
2=1/250 3=1/500
4=1/1000 5=1/2000
6=1/4000 7=1/10000
0= No function 1=1.5H
1023=1023.5H
0=Field 1=Frame
0=no clock out 1=clock out
0= active low 1= active high
0= active low 1= active high
0=AGC off 1=AGC on
0=low 255=high
0=low 255=high
0=manual gain 1=rear potm.
0=low 255=high
0=low 255=high
0=gamma 1 1=gamma 0.45
0=Factory data 1=User 1 area
2=User 2 area 3=User 3 area
1=User 1 area 2=User 2 area
3=User 3 area
Remarks
Off at power up
Actual setting
Command list
3 letter version
Partial scanning is
not supported
Continuous only
Trigger modes and
Continuous
CCIR. H=64µsec
EIA, H=63.5µsec
*1)
Should be off
when not used
*2)
0= manual gain
Range 0 to 255
Range 0 to 255
Range 0 to 255
Range 0 to 255
Latest used data
area becomes
default at next
power up