Related Manuals for Clarke TIGER 2500
Summary of Contents for Clarke TIGER 2500
- Page 1 WARNING: Read these instructions before using the machine PETROL DRIVEN POWER WASHER MODEL NO: TIGER 2500/2900 PART NO: 7320055/7320056 OPERATION & MAINTENANCE INSTRUCTIONS LS0511...
- Page 2 Faulty goods should be returned to their place of purchase, no product can be returned to us without prior permission. This guarantee does not effect your statutory rights. ACCESSORIES The range of accessories listed below may be purchased from your CLARKE dealer. ITEM PART NUMBER...
-
Page 3: General Safety Rules
3. NEVER allow children or untrained personnel to use this machine. 4. NEVER operate the machine with any of the covers removed. 5. NEVER attempt any repairs to this machine. Always refer to your Clarke dealer. 6. NEVER supply any liquid other than water to the water inlet. -
Page 4: Safety Symbols
SAFETY SYMBOLS WARNING: Risk of injection or severe injury. Do not direct discharge stream at persons or animals. Keep clear of nozzle. This machine is to be used only by qualified operators. WARNING: Risk of spray injury. Spray can propel objects. - Page 5 OVERVIEW DESCRIPTION NO DESCRIPTION Fuel Tank Cap Throttle Fuel Tank Engine On/Off Switch Spark Plug Oil Filler Cap Choke Water Outlet Gun Assembly Detergent Hose Lance Water Inlet Air Filter Cover Bypass Drain Hose Recoil Pull Start Hose Holder Fuel Valve Lance Holder Parts &...
-
Page 6: Connecting The Handle
ASSEMBLY Unpack your pressure washer and check to ensure the following items are present. Contact your Clarke dealer immediately if any parts are missing or damaged. • 1 x Petrol Pressure Washer • 1 x Spark Plug Box Spanner • 1 x Hose Holder c/w Fixings •... -
Page 7: Fitting The Rubber Feet
FITTING THE RUBBER FEET 1. Fit the rubber feet to the legs as shown. FITTING THE LANCE/HOSE HOLDER 1. Fit the holders into the positions shown and secure using the washers and nuts provided. ASSEMBLING THE LANCE 1. Connect the spray lance to the gun assembly and tighten securely by turning the locking ring. -
Page 8: Connecting The High Pressure Hose
CONNECTING THE HIGH PRESSURE HOSE CONNECT THE HOSE TO THE GUN 1. Screw the high pressure hose onto the gun assembly. • Tighten the connector, hand tight only. Do not use a spanner. NOTE: Make sure the connection is secure. CONNECT THE HOSE TO THE PRESSURE WASHER 1. -
Page 9: Before Use
BEFORE USE WARNING: TO CARRY OUT THIS CHECK, PLACE THE PRESSURE WASHER ON LEVEL GROUND WITH THE ENGINE SWITCHED OFF. WARNING: TAKE CARE NOT TO TOUCH ANY HOT PARTS OF THE PRESSURE WASHER WHEN CHECKING THE OIL LEVEL. IMPORTANT: The engine is supplied without any oil in it and must be filled to the correct level before use, see below. - Page 10 FUEL • Refuel in a well-ventilated area, away from any sources of ignition. • If the engine has been running, allow it to cool before refueling. • Do not leave fuel within the reach of children. • Refuel carefully to avoid spilling fuel. 1.
-
Page 11: Starting Your Pressure Washer
STARTING YOUR PRESSURE WASHER 1. Turn the water supply on, making sure that the tap is fully open. WARNING: FAILURE TO TURN ON THE WATER COULD CAUSE DAMAGE TO THE PRESSURE WASHER. 2. Set the choke lever to the OPEN position. - Page 12 5. Set the engine switch to the on (I) position 6. Pull the recoil starting handle lightly until you start to feel resistance and then pull up sharply to start the engine. • You may have to do this more than once.
-
Page 13: Interrupting Operation
INTERRUPTING OPERATION 1. Release the trigger. NOTE: The pressure washer will automatically go into bypass mode. WARNING: DO NOT ALLOW THE UNIT TO OPERATE IN BYPASS MODE FOR MORE THEN TWO MINUTES AT ANY TIME. TURN THE UNIT OFF IF IT IS NOT GOING TO BE USED FOR A PERIOD LONGER THAN THIS. -
Page 14: Applying Detergents And Cleaning Agents
CLARKE Traffic Film Remover which is a powerful low foaming agent for car cleaning, patio cleaning etc., or CLARKE Wash & Wax, both available from your CLARKE dealer. 2. Hold the rear of the nozzle on the high pressure lance and slide the front of the nozzle forwards to low pressure. -
Page 15: Before Storing The Pressure Washer
3. Turn off the engine switch, to the off (0) position. 4. Turn water supply off at the tap. 5. NEVER turn the water off with the engine running. 6. Release the pressure in the pump and hose by squeezing the trigger for a few seconds until no more water comes out of the nozzle. -
Page 16: Maintenance
MAINTENANCE CLEANING THE NOZZLE 1. Shut off the pressure washer and turn off the water supply. 2. Pull trigger on the gun handle to release any water pressure. 3. Disconnect the lance from the gun assembly. 4. Remove any obstructions with the nozzle cleaning tool provided and back flush with clean water. -
Page 17: Cleaning The Fuel Strainer
5. Rinse thoroughly and leave the elements to dry. Once it is completely dry, immerse the filter in clean engine oil and sqeeze to remove excess oil. • If the air filter is damaged contact Clarke spare parts department for a replacement. -
Page 18: Changing The Spark Plugs
CHANGING THE SPARK PLUGS CAUTION: ALLOW THE ENGINE TO COOL BEFORE REMOVING THE SPARK PLUG. 1. Remove the spark plug cap from the spark plug. 2. Use the spark plug spanner supplied to remove the spark plug. 3. Remove any carbon that has accumulated around the sparkplug. -
Page 19: Troubleshooting
TROUBLESHOOTING If the following does not solve your problem, please contact the CLARKE service department. PROBLEM CAUSE SOLUTION Engine will not No fuel. Add fuel. start (see engine Low oil. Add oil. manual for further engine Pressure builds up after... - Page 20 PROBLEM CAUSE SOLUTION Lack of pressure Choke lever is in the Set the choke lever to the OFF (right) (initial use) OPEN position. position. continued Throttle control lever is Move the throttle control lever to left. not set high enough. High pressure hose is too Make sure the high pressure hose is under long.
-
Page 21: Specifications
SPECIFICATIONS MODEL NO TIGER 2500 TIGER 2900 ENGINE Engine type Petrol (unleaded). OHV Petrol (unleaded). OHV Single Cylinder 4 stroke Single Cylinder 4 stroke forced air cooling forced air cooling Capacity/displacement: 118 cc 196 cc Oil Capacity 0.6 L 0.6 L... -
Page 22: Exploded Diagram (Tiger 2500)
EXPLODED DIAGRAM (TIGER 2500) WARNING: TO ENSURE MACHINE SAFETY, USE ONLY ORIGINAL SPARE PARTS FROM CLARKE INTERNATIONAL. Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com... -
Page 23: Parts List (Tiger 2500)
PARTS LIST (TIGER 2500) DESCRIPTION PART NO Locknut M5 RKTIG250001 Hose Holder RKTIG250002 Gasket RKTIG250003 Hex Bolt M5x40 RKTIG250004 High Pressure Hose RKTIG250005 4.0hp Engine RKTIG250006 Locknut M8 RKTIG250007 Gasket RKTIG250008 Hex Bolt M5x35 RKTIG250009 Inlet Connector RKTIG250010 Isolator RKTIG250011... -
Page 24: Exploded Diagram (Tiger 2900)
EXPLODED DIAGRAM (TIGER 2900) WARNING: TO ENSURE MACHINE SAFETY, USE ONLY ORIGINAL SPARE PARTS FROM CLARKE INTERNATIONAL. Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com... -
Page 25: Parts List (Tiger 2900)
PARTS LIST (TIGER 2900) DESCRIPTION PART NO Locknut M6 RKTIG290001 Hose Holder RKTIG290002 Washer RKTIG290003 Hex Bolt M6x45 RKTIG290004 High Pressure Hose RKTIG290005 6.5hp Engine RKTIG290006 Locknut M8 RKTIG290007 Washer RKTIG290008 Hex Bolt M6x40 RKTIG290009 Inlet Connector RKTIG290010 Mounting pad RKTIG290011 Frame RKTIG290012... -
Page 26: Declaration Of Conformity Tiger 2500
DECLARATION OF CONFORMITY TIGER 2500 Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com... - Page 27 DECLARATION OF CONFORMITY TIGER 2500 Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com...
-
Page 28: Declaration Of Conformity Tiger 2900
DECLARATION OF CONFORMITY TIGER 2900 Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com... - Page 29 DECLARATION OF CONFORMITY TIGER 2900 Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com...
- Page 30 NOTES Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com...
- Page 31 NOTES Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com...