System Information Display; Input Video Setup; Output Video Setup - Sony DFS-700 Service Manual

Setup Menu Settings
System Information Display (page 2/8)
Button Setting Meaning
F1 INFO Display options installed.
F2 INFO Display software version.
F3
PW ON Select setup mode at power on.
F5 INSTL Install new software.
Input Video Setup (page 3/8)
Button Setting Meaning
F1 In No. Select input to set.
F2 TYPE Select input signal format.
F3 TBC TBC Center setting for the input
signal
The output signal is output in the
correct phase if the phase
relationship of the center value with
respect to the reference
synchronizing signal is in the range
±0.3H.
F4 +H–pos Video phase adjustment of input
signal
F5 Cross-point button assignment to
+XPT
input signals
6-8
Chapter 6 System Connections and Settings
Values
CONFIG r BKDF-701/711/712
(Appears as "***" when not installed.)
To return, press F5(EXIT r).
VER r DFS-700/700P :x.xx
BKDF-712: x.xx
DATA: x.xx
Panel: x.xx
(Appears as "----" when not installed.)
To return, press F5(EXIT r).
FACTRY (factory default)/USER (user
settings)
r Press F3(OK) to confirm install; press
F5(CANCEL) to cancel.
Values (First value is factory default.)
1/2/3/4/5/6/7/8/DSK
SDI/YUV/Cps/YC/RGB/***
(Only types which can be set appear. See the table
on the next page. When F1(In No.) is set to DSK,
appears as "***".)
0H/0.5H/1H/***
This setting is not possible when TYPE is Cps or
YC.
• When SDI, YUV, Cps, YC, or RGB is selected, this
can be adjusted from –24 to +24 in steps of 2.
• When DSK is selected, this can be adjusted from
–30 to +31 in steps of 1.
1/2/3/4/5/6/7/8/***
(When F1(In No.) is set to DSK, appears as "***".)
To assign a signal, hold down the function key, and
press a cross-point button on the background bus.
Primary inputs and signal formats
SDI: serial digital signals
Component: analog component signals
Composite: analog composite signals
Input number 1 2 3 4
With standard SDI SDI SDI SDI
equipment
With BKDF-701 SDI SDI SDI
SDI
installed Component Component Component Component
RGB
With BKDF-702/ SDI SDI SDI SDI
702P installed Component Component Component Component
(mode 1) a) RGB
With BKDF-702/ SDI SDI SDI SDI
702P installed
(mode 2) b)
a) Setup menu item CpnIN set to "IN 1-4"
b) Setup menu item CpnIN set to "IN 5-8"
Output Video Setup (page 4/8)
Button Setting Meaning
F1 CLEAN Select output video from
CLEAN OUT connector.
F2 CLIP Toggle white clip and dark clip on/
off.
Only valid for SDI output signals,
and the SDI standard white and
dark values are applied.
F3
T-Area Toggle safe title indication on
preview video using CLEAN OUT
connector on/off.
When on, the safe title indication
shows approximately 85% of the
whole image area.
This item appears when F1(CLEAN)
is set to "PVW".
F4 FLD FZ Select the field output when the
internal frame memory is set to field
freeze mode.
YC: analog YC signals
RGB: analog RGB signals (G signal with sync)
5 6 7 8
Component Component Component Component
RGB
SDI SDI SDI SDI
Component Component Component Component
Composite Composite Composite Composite
YC YC YC YC
Component Component Component Component
Composite Composite RGB
Composite
YC YC YC Composite
YC
Values (First value is factory default.)
CLEAN/KEYOUT/PVW
(See page 2-15.)
OFF/ON
OFF/ON
ODD/EVEN
6-9
Chapter 6 System Connections and Settings