Table of Contents
Advertisement
20.2 AUXI Function
Following are functions to be able to assign to the
Auxiliary Input ports:
(Refer to Table 20-5 Assigning
functions to the Auxiliary Input ports.)
it is possible to assign three functions to each Auxiliary
Input port (1st, 2nd, and 3rd). When the signal is applied
Function Name
None
AUX Out 1 Off
-
AUX Out 5 Off
AUX I/O 1 Off
-
AUX I/O 6 Off
AUX Out 1 On
-
AUX Out 5 On
AUX I/O 1 On
-
AUX I/O 6 On
AUX Out 1
On/Off
-
AUX Out 5
On/Off
AUX I/O 1
On/Off
-
AUX I/O 6
On/Off
Channel 1
-
Channel 16
Channel Down
Channel Up
CW ID On
CW Message 1
-
CW Message 8
DC Power Save Off
DC Power Save On
Version: 1.01 USA
TKR-750/850/751/851 does not perform any operation.
When the signal is applied to one of the PF [AUX Out 1 Off] - PF [AUX Out 5 Off] input ports, the
function assigned to the Auxiliary Output port is disabled.
You can assign this function when "Selectable" is configured to the Auxiliary Output 1 to Auxiliary
Output 5 ports.
(Refer to 20.3 Assigning Functions to the Auxiliary Output Ports.)
When the signal is applied to one of the PF [AUX Out 1 Off] - PF [AUX Out 6 Off] input ports, the
function assigned to the Auxiliary I/O port is disabled.
You can assign the function when "Selectable" is configured to the Auxiliary I/O 1 to Auxiliary I/O
6 ports.
(Refer to 20.3 Assigning Functions to the Auxiliary Output Ports.)
When the signal is applied to one of the PF [AUX Out 1 On] - PF [AUX Out 5 On] input ports, the
function assigned to the Auxiliary Output port is enabled.
You can assign this function when "Selectable" is configured to the Auxiliary Output 1 to Auxiliary
Output 5 ports.
(Refer to 20.3 Assigning Functions to the Auxiliary Output Ports.)
When the signal is applied to one of the PF [AUX I/O 1 On] - PF [AUX I/O 6 On] input ports, the
function assigned to the Auxiliary I/O port is disabled.
You can assign the function when "Selectable" is configured to the Auxiliary I/O 1 to Auxiliary I/O 6
ports.
(Refer to 20.3 Assigning Functions to the Auxiliary Output Ports.)
You can enable/disable the function assigned to the Auxiliary Output port when a signal is applied to
one of the PF [AUX Out 1 On/Off] to PF [AUX Out 5 On/Off] input ports.
You can assign this function when "Selectable" is configure to the Auxiliary Output 1 to Auxiliary
Output 5 ports.
(Refer to 20.3 Assigning Functions to the Auxiliary Output Ports.)
You can use this function only when the signal is detected with the Down Edge.
Trigger Detection for Auxiliary Input Ports.)
You can enable/disable the function assigned to the Auxiliary I/O port when a signal is applied to
one of the PF [AUX I/O 1 On/Off] to PF [AUX I/O 6 On/Off] ports.
You can assign the function when "Selectable" is configured to the Auxiliary I/O 1 to Auxiliary I/O
6 ports.
(Refer to 20.3 Assigning Functions to the Auxiliary Output Ports.)
You can use this function only when the signal is detected with the Down Edge.
Trigger Detection for Auxiliary Input Ports.)
TKR-750/850/751/851 moves to a channel from one of CH 1 to CH 16 channels when a signal is
applied to one of the PF [Channel 1] to PF [Channel 16] ports.
You cannot configure this function when "Channel Select" is configured to Auxiliary
I/O 1 to Auxiliary I/O 4 ports. "E2" appears on the display when specifying the channel without
data.
(Refer to 20.1 AUX I/O Function.)
TKR-750/850/751/851 moves to the next lower channel when a signal is applied to the PF
[Channel Down] input port. The channel without data is skipped.
TKR-750/850/751/851 moves to the next higher channel when a signal is applied to the PF
[Channel Down] input port. The channel without data is skipped.
TKR-750/850/751/851 transmits a CW ID when a signal is applied to the PF [CW ID On] key.
This function is available on the channel having the CW
TKR-750/850/751/851 transmits one of the messages from CW Messages 1 to 8 when a signal is
applied to one of the PF [CW Message 1] to PF [CW Message 8] input
Message.)
TKR-750/850/751/851 switches the Save Mode off when a signal is applied to the PF [DC Power
Save Off] input port. Even if the signal is detected with the Down Edge, Save Mode does not
switch On after the mode is once enabled. It should be used with DC Power Save On function.
TKR-750/850/751/851 switches the Save Mode On when a signal is applied to the PF [DC Power
Save On] input port. Even if the signal is detected with the Down Edge, Save Mode does not
switch Off after the mode is once enabled. It should be used with DC Power Save Off function.
Function Reference (FUNC)
to the Auxiliary Input port, each function assigned to the
port is enabled one by one.
When assigning the "Channel Up" function to the
[Auxiliary Input 1] port, the port is referred to as the "PF
[Channel Up] input port".
Table 20-5 Assigning functions to the Auxiliary Input ports
(Functions in
are available only when the
Down Edge is detected.)
Description
ID.(Refer to 22.1 CW ID.)
20 FUNCTION PORT
(Refer to 20.2.1
(Refer to 20.2.1
ports.(Refer to 22.2 CW
46
Advertisement
Table of Contents
