15 KEY ASSIGNMENT
You can assign functions to PF1 to PF6 keys that are
located on the front panel of the TKR-750/850/751/851/
751/851.
! Configuration of KPG-91D
" Assigning functions to PF keys (Refer to FPRG 6.5
"Key Assignment" window.)
15.1 Available Functions
You can assign functions to PF1 to PF6 keys by KPG-
91D.
When the Channel Up function is assigned to the PF1
key, the PF1 key is referred to as "PF [Channel Up] key".
Table 15-1 Available functions
Name of
Description of functions
functions
TKR-750/850/751/851/751/851 does not
None
perform any operation.
You can enable/disable a function assigned
to an auxiliary output port by pressing one of
AUX Out 1
PF [AUX Out 1 On/Off] to PF [AUX Out 5 On/
On/Off
Off] keys.
-
You can assign functions when Selectable is
AUX Out 5
configured to an Auxiliary Output 1 to
On/Off
Auxiliary Output 5 port.
Assigning Functions to the Auxiliary Output
Ports.)
You can enable/disable a function assigned
to an auxiliary I/O port by pressing one of the
AUX I/O 1
PF [AUX Out 1 On/Off] to PF [AUX Out 6 On/
On/Off
Off] keys.
-
You can assign functions when Selectable is
AUX I/O 6
configured to the Auxiliary I/O 1 to Auxiliary I/
On/Off
O 6 ports.
(Refer to 20.3 Assigning Functions
to the Auxiliary Output Ports.)
Change a channel from one of CH 1 to CH
16 channels directly by pressing one of the
PF [Channel 1] to PF [Channel 16] keys.
Channel 1
TKR-750/850/751/851/751/851 cannot
-
configure this function when Channel Select
Channel 16
is configured to an Auxiliary I/O 1 to Auxiliary
I/O 4 ports. "E2" appears on the display
when specifying the channel has no data.
(Refer to 20.1 AUX I/O Function.)
Change channel to the next lower by
Channel Down
pressing a PF [Channel Down] key.
The blank channel is skipped.
Change channel to the next higher by
Channel Up
pressing the PF [Channel Up] key.
The blank channel is skipped.
Transmits a CW ID by pressing the PF [CW
ID On] key.
CW ID On
This function is available on a channel
having CW ID configuration.
Version: 1.01 USA
(Refer to 20.3
(Refer to 22.1 CW ID.)
Function Reference (FUNC)
Name of
Description of functions
functions
Transmits one of CW Message 1 to CW
CW Message 1
Message 8 by pressing one of the PF [CW
-
Message 1] to PF [CW Message 8] keys.
CW Message 8
(Refer to 22.2 CW Message.)
Enable/disable Save Mode by pressing the
DC Power Save
PF [DC Power Save On/Off] key.
On/Off
10.4 DC Power Save.)
Switch the panel LED On/Off by pressing the
PF [Display On/Off] key.
Display On/Off
This function operates only when TKR-750/
850/751/851/751/851 is in Save Mode.
Disable/enable the Repeat Hold Time by
pressing a PF [Hold Time Disable/Enable]
key.
Hold Time
You are able to configure this function only
Disable/Enable
when at least one channel is configured as
Repeat Operation mode and the Repeat
Hold Time is enabled.
Hold Time.)
Disable/enable a transmissions caused by
Local TX
Local Mic PTT by pressing the PF [Local TX
Disable/Enable
Disable/Enable] key.
Operation.)
Switch High or Low of a transmission power
by pressing the PF [Low Power On/Off].
Low Power
This function is available only when at least
On/Off
one channel is configured as High Power.
(Refer to 4.10 TX High Power.)
Disable/enable the Signalling Decode
Monitor On/Off
function by pressing a PF [Monitor On/Off]
key.
TKR-750/850/751/851 activates the Monitor
Monitor
function while pressing the PF [Monitor
Momentary
Momentary] key.
You can toggle between Main and Sub for
Multi Table
the signalling specified by the Multi-table
Main/Sub
Select by pressing the PF [Multi Table Main/
Sub] key.
(Refer to 20.1 AUX I/O Function.)
You can disable/enable the QT/DQT Decode
QT/DQT Decode
function by pressing the PF [QT/DQT
Disable/Enable
Decode Disable/Enable] key.
You can disable/enable the QT/DQT Encode
QT/DQT Encode
function by pressing the PF [QT/DQT
Disable/Enable
Encode Disable/Enable] key.
You can disable/enable a repeat operation by
pressing the PF [Repeat Disable/Enable]
Repeat Disable/
key.
Enable
You are not allowed to assign this function
when no channel is configured as Repeat
Operation mode.
The operation of the TKR-750/850/751/851
Reset
is reseted and it returns to the default value
by pressing the PF [Reset] key.
Enable/disable the Scan function by pressing
Scan On/Off
the PF [Scan On/Off] key.
(Refer to
(Refer to 6.5 Repeat
(Refer to 6 PTT
32