Table of Contents
Advertisement
18 REMOTE CONTROL
The TKR-750/850/751/851 has a function to be controlled
by another transceiver. You can remotely control the
assigned PF key function or the Auxiliary Port by the Air
Remote code.
Air Remote activates the functions configured to the TKR-
750/850/751/851(Channel Up function and Scan On/Off
function, etc.) when the code sent from other transceiver
is matched. The authorization code used for this function
is referred to as the "Air Remote code".
! Conditions to Activate the Air Remote
1. TKR-750/850/751/851 gives a preference to a status
of Auxiliary Input (Level) port if same function is
assigned on AUXI and Air remote function or PF key.
In this case, the Air remote command is canceled and
not transmit the Transpond code even when code is
matched. For example, when the scan function is
configured to the Auxiliary Input (Level) port and the
Scan is activating, the scan function of the PF keys
and the Air Remote become invalid.
2. It is possible to select a timing to transmit Transpond
code within "Before", "After" or "both" of the received
Air Remote code processing.
Before:
TKR-750/850/751/851 transmits a Transpond code
before the Air Remote code function is done.
After:
TKR-750/850/751/851 transmits a Transpond code
after the received Air Remote code function is done.
The Transpond code is not transmitted when the Air
Remote code function cannot be done. It means the
same thing as when the function is disabled
corresponding to the status against the PF key is
pressed, the function will be invalid.
Both:
TKR-750/850/751/851 transmits a Transpond code
before the Air Remote code function is done and after
the received code is done properly.
Note: The Transpond code is not sent when the transmission is
restricted.
3. Following channels are used to transmit the
Transpond code during scan:
Channel.)
Table 18-1 Transmit Channel:
Transmission event
During scan
AUX In & In (I/O)
Revert CH
AUX Out
Revert CH
Air Remote Transpond
Note:
# TKR-750/850/751/851 transmits a Transpond code while scan is
paused.
39
(Refer to 16.5 Revert
While scan is
paused.
Revert CH
Current CH
-
Current CH
Function Reference (FUNC)
# TKR-750/850/751/851 sends a Transpond code on the Revert
CH when the Scan is switched On during the Air Remote mode.
18.1 Control PF keys
You can control an assigned PF key function with the Air
Remote.
(Refer to 15 Key Assignment.)
You can configure the following functions relating to the
control of PF keys by KPG-91D.
PF Key Activation
PF Key Deactivation
PF Key Transpond
PF Key Transpond Activation
PF Key Transpond Deactivation
18.1.1 PF Key Activation
This function allows activates an assigned PF key
function by the Air Remote.
Assignment.)
TKR-750/850/751/851 activates the assigned PF key
function when a received code matches.
You can configure the Air Remote code by selecting the
Encode/Decode code of the DTMF.
! Configuration of KPG-91D
" Configuring the PF Key Activation (Refer to FPRG
6.9.1 "PF Key" tab.)
18.1.2 PF Key Deactivation
This function disables an assigned PF key function by the
Air Remote.
(Refer to 15 Key Assignment.)
The TKR-750/850/751/851 disables an assigned PF key
function when a received code matches.
You can configure the Air Remote code by selecting the
Encode/Decode code of the DTMF.
Note: it is impossible to configure this function that cannot be
disabled, such as Channel Up function.
! Configuration of KPG-91D
" Configuring the PF Key Deactivation (Refer to
FPRG 6.9.1 "PF Key" tab.)
(Refer to 15 Key
Version: 1.01 USA
Advertisement
Table of Contents
