Power Control - Kenwood TKR-750-850 Function Reference

10 POWER CONTROL

The TKR-750/850/751/851 has various power control
functions, such as the Power Save function, a function to
switch the power from the main power to the backup
power, and the operation when turning TKR-750/850/751/
851 ON. You can operate a assigned function
interlocking with Save On/Off, the Start Up operation, and
a function to switch the power from the main power and
the backup power.
• Save On/Off
• Start Up
• Backup Power
• Main Power
Table 10-1 Available functions
Name of
Description of functions
functions
TKR-750/850/751/851 does not perform any
None
operation.
The function assigned to a specified Auxiliary
Output port is disabled when TKR-750/850/
751/851 starts operation.
AUX Out 1 Off
You can assign functions when "Selectable"
-
is configured to the Auxiliary Output 1 -
AUX Out 5 Off
Auxiliary Output 5 ports.
(Refer to 20.3 Assigning Functions to the
Auxiliary Output Ports.)
The function assigned to a specified Auxiliary
I/O port is disabled when TKR-750/850/751/
851 starts operation.
AUX I/O 1 Off
You can assign functions when "Selectable"
-
is configured to the Auxiliary I/O 1 to
AUX I/O 6 Off
Auxiliary I/O 6 ports.
(Refer to 20.3 Assigning Functions to the
Auxiliary Output Ports.)
The function assigned to a specified Auxiliary
Output port is enabled when TKR-750/850/
751/851 starts operation.
AUX Out 1 On
You can assign functions when "Selectable"
-
is configured to the Auxiliary Output 1 -
AUX Out 5 On
Auxiliary Output 5 ports.
(Refer to 20.3 Assigning Functions to the
Auxiliary Output Ports.)
The function assigned to a specified Auxiliary
I/O port is enabled when TKR-750/850/751/
AUX I/O 1 On 851 starts operation.
- You can assign functions when "Selectable"
AUX I/O 6 On is configured to the Auxiliary I/O 1 - Auxiliary
I/O 6 ports.
Functions to the Auxiliary Output Ports.)
Move to the channel selected from CH 1 to
CH 16 immediately.
You are not allowed to perform this function
Channel 1
when Channel Select is configured to the
-
Auxiliary I/O 1 to Auxiliary I/O 4 ports. "E2"
Channel 16
appears on the display when specifying the
channel has no data.
(Refer to 20.1 AUX I/O Function.)
Decrease a channel to the next.
Channel Down
The blank channel is skipped.
Version: 1.01 USA
(Refer to 20.3 Assigning
Function Reference (FUNC)
Name of
Description of functions
functions
Increase a channel to the next.
Channel Up
The blank channel is skipped.
Transmits a CW ID when it starts operation.
(Refer to 22.1 CW ID.)
CW ID On
This function performs on a channel having
CW ID.
CW Message 1 Transmits a assigned CW tone from CW
- Messages 1 to 8 when it starts operation.
CW Message 8 (Refer to 22.2 CW Message.)
Exits Save Mode when it starts operation.
DC Power Save
You cannot configure this function to the
Off
Save On/Off Function.
Enters Save Mode when it starts operation.
DC Power Save
You cannot configure this function to the
On
Save On/Off Function.
All LEDs other than the Power SW LED that
is located on the front panel are unlit.
Display Off
This function activates only when TKR-750/
850/751/851 is in Save Mode.
All LEDs on the front panel light.
Display On This function activates only when TKR-750/
850/751/851 operates in Save Mode.
Disables the Repeat Hold Time.
You can configure this function only when at
Hold Time
least one channel is configured as Repeat
Disable
Operation mode and the Repeat Hold Time
is enabled. (Refer to 6.5 Repeat Hold Time.)
Enables the Repeat Hold Time.
You can configure this function only when at
Hold Time
least one channel is configured as Repeat
Enable
Operation mode and the Repeat Hold Time
is enabled. (Refer to 6.5 Repeat Hold Time.)
Local TX Disable Inhibits a transmission by Local Mic PTT.
Local TX Enable Enables a transmissions by Local Mic PTT.
Switches a transmission power from Low to
High.
Low Power Off*1 This function activates only when at least
one channel is configured as High for TX
Power. (Refer to 4.10 TX High Power.)
Switches a transmission power from High to
Low.
Low Power On*1 This function activates only when at least
one channel is configured as High for TX
Power. (Refer to 4.10 TX High Power.)
Monitor Off Enables a Signalling Decode function.
Monitor On Disables a Signalling Decode function.
The signalling specified in a Multi-table
Multi-table Sub Select is switched to the Sub-table.
20.1 AUX I/O Function.)
The signalling specified in the Multi-table
Multi-table Main Select is switched to the Main-table.
to 20.1 AUX I/O Function.)
Disables a QT/DQT Decode function. It
QT/DQT Decode becomes carrier squelch. This function
Disable activates even when the repeater is making
the repeat operation.
(Refer to
(Refer
24