Orion ODC-10000 User Manual page 29

DVI Converter
ODC-10000
- "Tracking Mode" Communication Sequence
* Wait for the response for 40msec after sending commands. In case of response failure, it is recommended to
send the command again.
* It is recommended not to give the other command or change the resolution during transmission.
* ALL DVIC command is executed Channel2 and Channel1 sequentially. (Channel2 → Channel1)
Tracking Mode Command transmission (to Ch2)
Tracking Mode Command transmission (to Ch1)
*"Get Tracking Values" command is executed Channel2 and Channel1 sequentially. (Channel2 → Channel1)
Get Tracking Mode Command transmission (to Ch2)
Get Tracking Mode Command transmission (to Ch1)
3.15. Default Data Load (Picture Control Data)
- The command for initializing the adjusted values and apply the built-in values.
- It is available only during Power on status.
- This commands should be executed with care, because all the adjusted values will be erased.
- Send to MPDP
STX CMD Length
Value 0x02 0x97 0x02
* ID range (Program): 0x65(101) ~ 0x6D(109)
* Ch1/Ch2: Channel1 (0x01), Channel2 (0x00)
- Receive from MPDP
STX CMD Length
Value 0x02 0x97 0x02
* ID range (Program): 0x65(101) ~ 0x6D(109)
* Ch1/Ch2: Channel1 (0x01), Channel2 (0x00)
* Check Sum: Add all the values of "STX ~ Data" and execute "Not" operation.
54 | ORION PDP CO., LTD.
→
Tracking Mode Response transmission (from Ch2)
←
→
Tracking Mode Response transmission (from Ch1)
←
→
Get Tracking Mode Response transmission (from Ch2)
←
→
Get Tracking Mode Response transmission (from Ch1)
←
Data
ETX
ID Ch1/Ch2
Variable Variable 0x03
Data
Check Sum ETX
ID Ch1/Ch2
Variable Variable Variable 0x03
- "Default Data Load" Communication Sequence
* Wait for the response for 40msec after sending commands. In case of response failure, it is recommended to
send the command again.
* It is recommended not to give the other command or change the resolution during transmission.
* ALL DVIC command is executed Channel2 and Channel1 sequentially. (Channel2 → Channel1)
Default Data Load Command transmission (to Ch2)
Default Data Load Command transmission (to Ch1)
3.16. Graphic User Mode Control
- The command for adjusting the values of Brightness, Contrast, Sharpness, Color, and Tint.
- CMD: 0x8F (Brightness), 0x90 (Contrast), 0x91 (Sharpness), 0x92 (Color), 0x93 (Tint)
- It is available only during Power on status.
- The adjusted value will not be applied during stand-by phase or no input signal.
So, there must be input signals of corresponding mode to apply adjusted values.
- Send to MPDP
STX CMD Length
Value 0x02 Variable 0x03
* ID range (Program): 0x65(101) ~ 0x6D(109)
* Ch1/Ch2: Channel1 (0x01), Channel2 (0x00)
* Value:
x Brightness ("0" ~ "100"), Contrast ("0" ~ "100"), Sharpness ("0" ~ "28"), Color ("0" ~ "100"), Tint ("0" ~ "100")
- Receive from MPDP
STX CMD Length
Value 0x02 Variable 0x02
* ID range (Program): 0x65(101) ~ 0x6D(109)
* Ch1/Ch2: Channel1 (0x01), Channel2 (0x00)
* Check Sum: Add all the values of "STX ~ Data" and execute "Not" operation.
- "Graphic User Mode Control" Communication Sequence
* Wait for the response for 40msec after sending commands. In case of response failure, it is recommended to
send the command again.
* It is recommended not to give the other command or change the resolution during transmission.
* ALL DVIC command is executed Channel2 and Channel1 sequentially. (Channel2 → Channel1)
Infinitely Expandable
→
Default Data Load Response transmission (from Ch2)
←
→
Default Data Load Response transmission (from Ch1)
←
Data
ETX
ID Ch1/Ch2 Value
Variable Variable Variable 0x03
Data
Check Sum ETX
ID Ch1/Ch2
Variable Variable Variable 0x03
ORION PDP CO., LTD. | 55