Orion ODC-10000 User Manual page 26

DVI Converter
ODC-10000
- Send to MPDP
STX CMD Length
Value 0x02 0xA0 0x03
* ID range (Program): 0x65(101) ~ 0x6D(109)
* Ch1/Ch2 : Channel1 (0x01), Channel2 (0x00)
* Value
x DVI (0x01), HDMI (0x02), HDSDI (0x03), PC (0x04), DTV (0x05), S-VIDEO (0x06), VIDEO (0x07)
x If the Main Input-Mode is DVI, HDMI, or HDSDI, PIP Input-Mode cannot be DVI, HDMI, or HDSDI.
x If the Main Input-Mode is PC, DTV, S-VIDEO, or VIDEO, PIP Input-Mode cannot be PC, DTV, S-VIDEO, or
VIDEO.
x Main Input-Mode and PIP Input-Mode cannot have the same input source.
- Receive from MPDP
STX CMD Length
Value 0x02 0xA0 0x02
* ID range (Program): 0x65(101) ~ 0x6D(109)
* Ch1/Ch2: Channel1 (0x01), Channel2 (0x00)
* Check Sum: Add all the values of "STX ~ Data" and execute "Not" operation.
- "Input-Mode Change" Communication Sequence
* Wait for the response for 40msec after sending commands. In case of response failure, it is recommended to
send the command again.
* It is recommended not to give the other command or change the resolution during transmission.
* ALL DVIC command is executed Channel2 and Channel1 sequentially. (Channel2 → Channel1).
Input-Mode Change Command transmission (to Ch2)
Input-Mode Change Command transmission (to Ch1)
3.9. Get PIP Status
- The command for checking PIP status information.
- It is available only during Power on status.
- CMD: 0x5F
- Send to MPDP
STX CMD Length
Value 0x02 0x5F 0x02
* ID range (Program): 0x65(101) ~ 0x6D(109)
* Ch1/Ch2: Channel1 (0x01), Channel2 (0x00)
48 | ORION PDP CO., LTD.
Data
ETX
ID Ch1/Ch2 Value
Variable Variable Variable 0x03
Data
Check Sum ETX
ID Ch1/Ch2
Variable Variable Variable 0x03
→
Input-Mode Change Response transmission (from Ch2)
←
→
Input-Mode Change Response transmission (from Ch1)
←
Data
ETX
ID Ch1/Ch2
Variable Variable 0x03
- Receive from MPDP
STX CMD Length
Value 0x02 0x5F 0x07
* ID range (Program): 0x65(101) ~ 0x6D(109)
* Ch1/Ch2: Channel1 (0x01), Channel2 (0x00)
* Check Sum: Add all the values of "STX ~ Data" and execute "Not" operation.
* Status
No. Data Length
1 PIP Mode 1 byte
2 PIP H. Position 1 byte
3 PIP V. Position 1 byte
4 PIP Input Source 1 byte
5 PIP Swap Mode 1 byte
- "PIP Status Get" Communication Sequence
* Wait for the response for 40msec after sending commands. In case of response failure, it is recommended to
send the command again.
* It is recommended not to give the other command or change the resolution during transmission.
* ALL DVIC command is executed Channel2 and Channel1 sequentially. (Channel2 → Channel1)
PIP Status Get Command transmission (to Ch2)
PIP Status Get Command transmission (to Ch1)
3.10. Output Resolution Change
- The command for changing the output resolution of DVI Converter
- It is available only for PIP mode during Power on status. In case of PIP mode, it becomes PIP Normal mode.
- Send to MPDP
STX CMD Length
Value 0x02 0xA2 0x03
* ID range (Program): 0x65(101) ~ 0x6D(109)
* Ch1/Ch2: Channel1 (0x01), Channel2 (0x00)
* Value
x 640x480(60Hz) (0x01), 640x480(85Hz) (0x02), 800x600(50Hz) (0x03), 800x600(60Hz) (0x04),
800x600(85Hz) (0x05), 853x480(50Hz) (0x06), 853x480(60Hz) (0x07), 1024x768(60Hz) (0x08),
1024x768(85Hz) (0x09), 1280x1024(50Hz)(0x0A), 1280x1024(60Hz) (0x0B), 1600x900(50Hz) (0x0C),
1600x900(60Hz) (0x0D), 1600x1200(50Hz) (0x0E), 1600x1200(60Hz) (0x0F), 1706x960(60Hz) (0x10),
1080P(50Hz)(0x11), 1080P(60Hz)(0x12)
Infinitely Expandable
Data
Check
ETX
Sum
ID Ch1/Ch2 Status
Variable Variable ... Variable 0x03
Explanation
1:Normal, 2: PIP
0 (0x00) ~ 100 (0x64)
0 (0x00) ~ 100 (0x64)
1: DVI, 2: HDMI, 3: HDSDI, 4: PC, 5: DTV, 6: S-Video, 7: Video
1: Normal, 2: Swap
→
PIP Status Get Response transmission (from Ch2)
←
→
PIP Status Get Response transmission (from Ch1)
←
Data
ETX
ID Ch1/Ch2 Value
Variable Variable Variable 0x03
ORION PDP CO., LTD. | 49