Description Of The Appliance - EURO EG90GFSX Operating And Installation Instructions

ELECTRONIC PROGRAMMER
The programmer can select the following functions:
- Clock
- Minute counter
- Cooking time
- End of cooking
- Manual operation mode
- Setting time backwards
- Setting time forward
The digital display (N) always shows the time and
can display cooking and end of cooking time or the
minute counter time by pressing the corresponding
push button.
N.B.: At the end of each setting session (except
for the minute counter) the programmer turns the
oven off. Check when next using the oven, if the
programmer is not going to be used, that the latter
is set on manual operation (see the instructions
given further on).
Setting the time (from 0.01 to 24.00 = hh,mm)
After connecting to the electricity mains or subsequent
to a power cut, AUTO and "0.00" will both flash
simultaneously on the display.
Press push buttons 2 and 3 simultaneously and start
setting the current time by pressing push button 5 or 6.
Once set the AUTO symbol will turn off and
the symbol, for manual operation, will turn on.
Minute counter (from 0.01 to 0.59 = hh,mm)
Press push button 1 and select cooking time with push
button 5 or 6. The
the set time the buzzer will go off and the
turns off.
Semi-automatic operation
(with cooking time from 0.01 to 23.59 = hh,mm)
By pressing push button 2 and setting the length of
cooking time with push button 5 or 6, the AUTO and
symbols will light up and stay on all the time. At the end
of the set time the
symbol will flash and the buzzer will go off.
Semi-automatic operation
(with end of cooking time from 0.01 to 23.59 = hh,mm)
By pressing push button 3 and setting the end of
cooking time with push button 6, the AUTO and
symbols will turn on and stay on all the time. At the end
of the set time the
symbol will flash and the buzzer will go off.

DESCRIPTION OF THE APPLIANCE

(set by keys 2 and 3)
(set by key 1)
(set by key 2)
(set by key 3)
(set by key 4)
(set by key 5)
(set by key 6)
symbol turns on. At the end of
symbol will turn off, the AUTO
symbol will turn off, the AUTO
� � � � � � �
Automatic operation
(with the start of cooking time delayed)
First programme cooking time (both the AUTO
and symbol will turn on) and then the end of
cooking time (the
previously. The
baking in the oven starts. At the end of cooking time
the symbol will turn off, the AUTO symbol will flash
and the buzzer will go off.
Manual operation
Manual operation is only possible when the automatic
programming has finished or after having cancelled it by
pressing push button 4. The AUTO symbol disappears
and the
Buzzer
The buzzer will go off at the end of a programme or at
the end of the minute counter function and lasts about 7
minutes. The buzzer can be stopped by pressing one of
the function push buttons.
Programme start and control
The programme starts after setting. The programme
symbol
set can be controlled at any time by pressing the
corresponding push button.
Correcting/cancelling the programme setting
An automatic function programming error will occur if the time
shown on the clock is between the cooking start time and
cooking end time. This error will be signalled immediately
by a buzzer and the AUTO symbol will flash. A setting error
can be corrected by altering the duration or end of cooking
time. Any programme that has been set can be corrected
at any time by pressing the corresponding programming
key and then key 5 or 6. To cancel a programme, correct
the time set bringing it to a value of "0.00". If functioning
time is cancelled the end of functioning is cancelled too
and vice versa. The oven turns off automatically and the
AUTO symbol flashes. Press key 4 to set the programmer
on manual operation. The right time cannot be corrected
when the automatic operation programme is working.
8
�
�
�
�
�
symbol will turn off) as described
symbol will turn on again when
symbol turns on.
�