Advertisement
warnInG: TO reduce The rIsK OF FIre, elecTrIc shOcK, Or InJury TO persOns,
OBserve The FOllOwInG: read and save These InsTrucTIOns
1.
Installation work and electrical wiring must be done by qualified person(s) in accordance with applicable codes and standards (ANSI/NFPA 70-1999),
including fire-rated construction.
2.
Use this unit only in the manner intended by the manufacturer . If you have any questions contact the manufacturer .
3.
After making the wire connections, the wires should be spread apart with the grounded conductor and the equipment-grounding conductor on one side
of the outlet box and ungrounded conductor on the other side of the outlet box. The splices, after being made, should be turned upward and
pushed carefully up into the outlet box.
4.
warnInG: Before you begin installing the fan, servicing or cleaning unit, Switch power off at Service panel and lock service disconnecting means to
prevent power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a prominent warning
device, such as a tag, to the service panel.
5.
Be cautious! read all instructions and safety information before installing your new fan. Review the accompanying assembly diagrams.
6.
When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden utilities.
7.
Make sure the installation site you choose allows the fan blades to rotate without any obstructions. Allow a minimum clearance of 7 feet from the floor to
the trailing edge of the blade.
warnInG: To reduce the risk of fire, electric shock, or personal injury, mount to outlet box or supporting system acceptable for fan support.
8.
(Mounting must support at least 35 lbs.)
9.
warnInG: To reduce the risk of personal injury, do not bend blade holders during installation to motor , balancing or during cleaning. Do not insert for-
eign object between rotating blades.
10.
Attach the mounting bracket using only the hardware supplied with the outlet box.
11.
warnInG: To reduce the risk of fire or electric shock, do not use this fan with any solid state fan speed control device, or variable speed control.
12.
If this unit is to be installed over a tub or shower , it must be marked as appropriate for the application.
13.
NEVER place a switch where it can be reached from a tub or shower .
14.
The combustion airflow needed for safe operation of fuel-burning equipment may be affected by this unit's operation. Follow the heating equipment man-
ufacturer's guideline safety standards such as those published by the National Fire Protection Association (NFPA), and the American Society for Heating,
Refrigeration and Air Conditioning Engineers (ASHRAE) and the local code authorities.
15.
cauTIOn: To Reduce the Risk of Electric Shock, Disconnect the electrical supply circuit to the fan before installing the light kit.
16.
All set screws must be checked and tightened where necessary before installation.
Phillips Screwdriver
1
Before you begin installing the fan, Switch
power off at Service panel and lock service dis-
connecting means to prevent power from being
switched on accidentally. When the service dis-
connecting means cannot be locked, securely
fasten a prominent warning device, such as a
tag, to the service panel.
4
Downrod mount installation
Remove the cotter pin from the downrod
and save it for later use.
Installation
s
T
aFeTy
Ips
TOOls reQuIred
Wire Cutters
2
Before installing this fan make sure the outlet box is
properly installed to the house structure. To reduce
the risk of fire, electric shock, or personal injury,
mount to outlet box or supporting system acceptable
for fan support. (Mounting must support at least 35
lbs.)
5
Canopy disk
Downrod
Canopy
Tread leadwires and safety cable first
through the canopy disk, canopy and last
the downrod.
Pliers
Step Ladder
3
Use metal outlet box suitable for fan support
(must support 35 lbs). Before attaching fan to
outlet box, ensure the outlet box is securely
fastened by at least two points to a structural
ceiling member ( a loose box will cause the fan
to wobble). use only the screws provided
with the outlet box.
6
Cross Pin
Keeper
Pin
Insert downrod into yoke on top of the Fan
Body. Align the hole in the Downrod with the
hole in the Yoke. Insert the Pin through the
Yoke and Downrod until the point appears on
the other side. Install the Keeper Pin
Yoke
Advertisement
