Changing The Handset Name - Panasonic KX-TG8051PD Operating Instructions Manual

TG8051_8061PD(e-hg).book Page 28 Wednesday, February 2, 2011 2:33 PM
Programming
Fontos:
L Set the date and time beforehand (15. oldal).
L We recommend turning the base unit ringer off
(25. oldal) in addition to turning the night mode
on. (KX-TG8061)
L If you have set the alarm, the alarm sounds even
if the night mode is turned on.
Turning night mode on/off
1
1 (middle soft key) (238
2
{r}: Select the desired setting. s M
L If you select "KI", press {ic} to exit.
3
Enter the desired hour and minute you wish to
start this feature. s M
L You can select 24-hour or 12-hour clock
format ("AM" or "PM") by pressing /.
4
Enter the desired hour and minute you wish to
end this feature. s M
5
{ic}
L When the night mode is set, f is
displayed.
Changing the start and end time
1
1 (middle soft key) (237
2
Continue from step 3, „Turning night mode
on/off", 28. oldal.
Setting the ring delay
This setting allows the handset to ring during night
mode if the caller waits long enough. After the
selected amount of time passes, the handset rings.
If you select "Nincs cseng.", the handset never
rings during night mode.
1
1 (middle soft key) (239
2
{r}: Select the desired setting. s M s
{ic}
Megjegyzés:
L When the answering system answers the call,
this feature does not work. (KX-TG8061)
Selecting categories to bypass night
mode
1
1 (middle soft key) (241
2
{r}: Select your desired categories. s t
L "Q" is displayed next to the selected
category numbers.
L To cancel a selected category, press t
again. "Q" disappears.
3
M s {ic}
28
Megjegyzés:
L You can also select the categories in step 2 as
follows:
Press 1 to 9. s M

Changing the handset name

Each handset can be given a customised name
("Bob", "Kitchen", etc.). This is useful when you
make intercom calls between handsets. You can
also select whether or not the handset name is
displayed in standby mode. The default setting is
"NEM". If you select "IGEN" without entering any
handset name, "Kézibesz. 1" to "Kézibesz.
6" is displayed.
1
1 (middle soft key) (1)4
2
Enter the desired name (max. 10 characters;
43. oldal).
L If not required, go to step 3.
3
M
4
{r}: Select the desired setting. s M 2 times
5
{ic}
Incoming call barring (Caller ID
subscribers only)
This feature allows the unit to reject calls from
specified phone numbers that you do not want to
answer such as junk calls.
When a call is received, the unit does not ring while
the caller is being identified. If the phone number
matches an entry in the call barred list, the unit
sends out a busy tone to the caller, and then
disconnects the call.
Fontos:
L When the unit receives a call from a number that
is stored in the call barred list, the call is logged
in the caller list (32. oldal) with 7 after the call is
disconnected.
Storing unwanted callers
You can store up to 30 phone numbers in the call
barred list.
Fontos:
L You must store the phone number with an area
code in the call barred list.
■ From the caller list:
1
{<} (y)
2
{r}: Select the entry to be barred. s M
s I
3
{r}: "Bejövő szám tiltása" s M
4
{r}: "IGEN" s M s {ic}