Yamaha FZ1-N Service Manual page 71

1. Clutch cable
2. Water pump breather hose
3. Oil level switch lead
4. Sidestand switch lead
5. O sensor lead
2
6. Coolant reservoir tank drain hose
7. Wire harness
8. Battery negative lead
9. Seat lock cable
10.AC magneto lead
11.Rectifier/regulator lead
12.Water pump inlet pipe
13.Radiator fan motor lead (left)
14.Radiator stay
15.Main switch lead
16.Immobilizer lead
17.Left handlebar switch lead
18.Horn
19.Clutch cable swaging metal
20.Throttle cable
21.Stay assembly
22.Upper bracket
23.Right handlebar switch lead
24.Brake hose
25.Horn lead
26.Throttle body
27.Stay 1
28.Drive chain case cover
29.Starter motor lead
30.Fuel tank breather hose
31.EXUP cables
32.Rear brake light switch lead
33.Rear brake fluid reservoir hose
34.Speed sensor lead
A. Route in the concavity section of the radia-
tor stay.
B. To the coolant reservoir tank
C. Clamp the wire harness, AC magneto lead,
rectifier/regulator lead, starter motor lead
and battery negative lead. Point the clamp
head to the inside of the vehicle and fit it so
that the band tip is pointed downward.
D. Pass the O sensor lead through the vehi-
2
cle inner side of the hose assembly 1 junc-
tion pipe of the water pump inlet pipe and
route it by the outer down side of the hose
assembly 1 and to the upper direction as
shown in the illustration.
E. To the exhaust
F. Route the O sensor lead to the vehicle
2
rear side where the water pump inlet pipe
is routed.
G. Physical relationship between the coolant
reservoir tank drain hose tip and sidestand
switch lead can be in random order.
H. Route the hose assembly 1 by the vehicle
front side where the water pump inlet pipe
is routed. For the hose tip position, route
the hose so that 10 mm (0.39 in) or more
can be assured as shown in the illustration.
I. More than 10 mm (0.39 in)
J. Route the sidestand switch lead by the
vehicle front side where the hose assembly
1 and water pump inlet pipe are routed.
K. Pass the oil level switch lead to the vehicle
front side of the water pump breather hose
and water pipe.
L. Route the AC magneto lead by the inside
of the frame.
M. There should be no exposure of bare con-
ductors due to the misalignment of tubes.
N. Route the AC magneto lead by the inside
of vehicle away from the water hose.
O. Clamp the clutch cable, radiator fan motor
lead (left) and water pump breather hose.
Point the clamp head to the upper side of
the vehicle and fit it so that the band tip is
positioned inside. For the band position,
install the band using the engine position
as a guide as shown in the illustration.
P. Insert the clamp to the frame and clamp
the clutch cable. For the clamping position,
place the clamp so that the caulking
attachment on the clutch cable side is posi-
tioned at the vehicle front side where the
clamp is located. Clamp opening should be
positioned at the outside of the vehicle.
Q. The inserting direction of the onion-head of
the horn lead shall be as shown in the illus-
tration.
R. The front side of the vehicle.
S. The outside of the vehicle.
T. The upper side of the vehicle.
U. The inside of the vehicle.
V. Route the clutch cable under the convexity
sections of the throttle bodies.
W. Route the radiator fan motor lead (left)
between the convexity sections of the throt-
tle bodies.
X. Route the wire harness between the con-
vexity sections of the throttle bodies.
Y. Innermost section of the vehicle.
Z. Can be routed in any order.
AA.Route the water pump breather hose
finally in the guide after passing other
hoses so that it can be positioned on the
outside of the vehicle.
AB.Route the coolant reservoir tank drain
hose so that it is positioned at the inner-
most part in hoses and leads.
AC.The rear side of the vehicle.
AD.To the radiator
AE.Open to the air
2-44
CABLE ROUTING