Smartjet System; Comfort Control ® System; Moto-Massage Jet; Moto-Massage Dx Jet - HotSpring Vista Owner's Manual

Operational Note: Make sure you adjust your Total Alkalinity first, as an out-of-balance condition will affect your ability to adjust the pH
correctly, and will prevent the sanitizer from operating effectively. The spa is ready for use when the spa water has circulated through
each SmartJet lever operating position and the chlorine level remains between 3 ppm and 5 ppm.
11. The spa temperature is pre-programmed to reach 100°F (38°C), and will normally do so within 18 to 24 hours. You may raise the water
temperature by pressing the TEMP ▲ button on the control panel, or lower it by pressing TEMP ▼ button (press the OPTIONS hard button
followed by the Temperature soft button for desired screen). After a few hours, the water temperature will remain within 2 degrees of your
selected temperature. To prevent tampering, you can lock your desired temperature setting. Refer to the Control Panel section for details.
NOTe: Allowing the jet pump to operate for long uninterrupted periods of time with the cover in place will cause a rise in the spa water temperature.
All spas are equipped with a safety device to reduce the risk of component damage or personal injury, should the jet pump be left running
continuously for a long period of time. After two hours of continuous operation, the jet pump controller will automatically turn off the jet pump.

SMARTJeT SySTeM

®
With your Hot Spring spa's exclusive SmartJet system, you can control the
massaging action of your spa. Using the SmartJet lever, the jets are activated in sets,
known as jet systems.
Each SmartJet lever controls two jet systems. To access a jet system, simply
turn the SmartJet lever to the 3 o'clock or 9 o'clock position. Please consult the
jet system menus on the following pages to determine which jets are activated with
each SmartJet lever position. Or just jump in and play – turn the lever(s) and see what
happens.
COMfORT CONTROl
The Comfort Control system allows you to control the intensity of the massage at each jet by
adjusting the mixture of air and water. Jets with an adjustable faceplate are controlled
by turning the faceplate clockwise for a softer flow, counterclockwise for a stronger
flow. Jets without an adjustable faceplate are controlled by a Comfort Control lever. The
® ®
Precision , Moto-Massage
NOTe: The intensity of the JetStream jets in the footwell can not be altered.
Turn the Comfort Control lever clockwise to increase the intensity of the jet and
counterclockwise to decrease the intensity.

MOTO-MASSAge JeT

The Moto-Massage jet automatically travels up and down in a sweeping motion, simulating the natural stroking effects of a manual
massage. The intensity of the Moto-Massage jet may be adjusted by turning the Comfort Control lever.
The Moto-Massage jet has been factory adjusted to provide maximum hydromassage, and to achieve full vertical travel with its Comfort
Control lever in the full air volume position. Should the Moto-Massage
air control valve or clogged filter cartridge, then your Hot Spring Service Center should be contacted.
SeRvICe NOTe: A slow or non-moving Moto-Massage jet may indicate that the filter cartridge pores are obstructed with dirt, body oils,
or calcification. Follow the filter cartridge cleaning procedures in the Spa Care and Maintenance section of this manual.
ACCeSSORy NOTe: For a different-feeling massage, ask your dealer about the HydroPulse
Moto-Massage jet.

MOTO-MASSAge dX JeT

The Moto-Massage DX automatically travels two streams up and down in a sweeping motion, simulating the natural stroking effects of
a manual massage. The intensity of the Moto-Massage DX jet may be adjusted by turning the Comfort Control lever.
The Moto-Massage DX jet has been factory adjusted to provide maximum hydromassage, and to achieve full vertical travel with its
Comfort Control lever in the full air volume position. Should the Moto-Massage DX jet not achieve full vertical travel and the problem is
not a closed air control valve or clogged filter cartridge, then your Hot Spring Service Center should be contacted.
SeRvICe NOTe: A slow or non-moving Moto-Massage DX jet may indicate that the filter cartridge pores are obstructed with dirt, body
oils, or calcification. Follow the filter cartridge cleaning procedures in the Spa Care and Maintenance section of this manual.
®
SySTeM
®
and JetStream jets are controlled by Comfort Control levers.
(vANgUARd
9 o'clock
®
SPA ONly)
®
jet not achieve full vertical travel and the problem is not a closed
Page 28
Decrease Air
Volume
option; an alternative faceplate for your
®
operating Instructions
3 o'clock
Increase Air
Volume