Venting; Equivalent Vent Length (Evl); Installation Configurations; Installation Configurations Installation Configurations - Enerzone Euromax Owner's Manual

1.6. 1.6.

VENTING

VENTING
1.6. 1.6. VENTING VENTING
In Canada, we recommend that you use a listed pellet vent that meets the ULC S-609-M89/ORD C441-M90 Standard.
For the United States, we recommend that you use a listed pellet vent that meets the UL-641Standard.
This unit can be vented in an existing factory-built or masonry chimney with the addition of a liner, provided the chimney
is more than 4" in diameter. The liner should be listed and should meet the ULC S-635/640 standard in Canada and the UL-
1777 standard in the USA. Refer to the instructions provided by the vent or chimney manufacturer, especially when passing
through a wall, ceiling, or roof.
Your venting system should have at least one foot of vertical rise for each foot of horizontal run. Th Your venting system should have at least one foot of vertical rise for each foot of horizontal run. The total vertical rise Your venting system should have at least one foot of vertical rise for each foot of horizontal run. Th Your venting system should have at least one foot of vertical rise for each foot of horizontal run. Th
should never be less than 3 feet (see Appendix A). should never be less than 3 feet (see Appendix A). should never be less than 3 feet (see Appendix A). should never be less than 3 feet (see Appendix A).
This unit uses a pressurized exhaust system. All vent connector joints must be sealed and fastened. If vented horizontally,
joints should be made gastight. Please consult the pellet pipe manufacturer's instruction to ensure proper installation
and consistent performance to avoid smoke and ash spillage.
DO NOT CONNECT THIS UNIT TO A CHIMNEY FLUE SERVING ANOTHER APPLIANCE. DO NOT CONNECT THIS UNIT TO A CHIMNEY FLUE SERVING ANOTHER APPLIANCE.
DO NOT CONNECT THIS UNIT TO A CHIMNEY FLUE SERVING ANOTHER APPLIANCE. DO NOT CONNECT THIS UNIT TO A CHIMNEY FLUE SERVING ANOTHER APPLIANCE.
DO NOT INSTALL A FLUE DAMPER IN DO NOT INSTALL A FLUE DAMPER IN DO NOT INSTALL A FLUE DAMPER IN DO NOT INSTALL A FLUE DAMPER IN THE EXHAUST VENTING SYSTEM OF THIS UNIT.
INSTALL VENT AT CLEARANCES SPECIFIED BY THE VENT MANUFACTURER. INSTALL VENT AT CLEARANCES SPECIFIED BY THE VENT MANUFACTURER.
INSTALL VENT AT CLEARANCES SPECIFIED BY THE VENT MANUFACTURER. INSTALL VENT AT CLEARANCES SPECIFIED BY THE VENT MANUFACTURER.
WARNING : WARNING : DO NOT INSTALL IN SLEEPING ROOM DO NOT INSTALL IN SLEEPING ROOM
WARNING : WARNING : DO NOT INSTALL IN SLEEPING ROOM DO NOT INSTALL IN SLEEPING ROOM
CAUTION : CAUTION : THE STRUCTURAL INTEGRITY OF THE MANUFACTURED HOME FLOOR, WALL, AND CAUTION : CAUTION : THE STRUCTURAL INTEGRITY OF THE MANUFACTURED HOME FLOOR, WALL, AND CEILING/ROOF MUST BE MAINT THE STRUCTURAL INTEGRITY OF THE MANUFACTURED HOME FLOOR, WALL, AND THE STRUCTURAL INTEGRITY OF THE MANUFACTURED HOME FLOOR, WALL, AND
CAUTION : CAUTION : CAUTION : THE CHIMNEY CONNECTOR SHALL NOT PASS TROUGH AN ATTIC OR ROOF SPACE, CLOSET OR SIMILAR CONCEALED CAUTION : THE CHIMNEY CONNECTOR SHALL NOT PASS TROUGH AN ATTIC OR ROOF SPACE, CLOSET OR SIMILAR CONCEALED THE CHIMNEY CONNECTOR SHALL NOT PASS TROUGH AN ATTIC OR ROOF SPACE, CLOSET OR SIMILAR CONCEALED THE CHIMNEY CONNECTOR SHALL NOT PASS TROUGH AN ATTIC OR ROOF SPACE, CLOSET OR SIMILAR CONCEALED
SPACE SPACE SPACE SPACES, OR S, OR FLOOR S, OR S, OR FLOOR FLOORS S S S , OR CEILING FLOOR
1.6.1. 1.6.1. 1.6.1. 1.6.1.

Equivalent Vent Length (EVL)

Equivalent Vent Length (EVL) Equivalent Vent Length (EVL) Equivalent Vent Length (EVL)
The longer the run of pipe in your installation, the greater
the restriction in your system.
•
Always use 4" pipe
•
Horizontal runs shall not exceed 30 feet of EVL.
To calculate EVL, use the following conversions table:
Qty Qty Qty Qty Type of pipe Type of pipe Type of pipe Type of pipe
1 90° elbow or "T"
1 45° elbow
1 ft Horizontal pipe run
1 ft Vertical pipe run
Here is an example on how to calculate the EVL of your
installation. (See Figure 10):
(3 x 4' of vertical length = 12' x 0.5 = 6 EVL) +
(1 x elbow or "T" = 5 EVL) +
(2 x 1' of horizontal length = 2 EVL)
Total EVL = (6 + 5 +2) = 13.
1.6.2. 1.6.2.

Installation Configurations

Installation Configurations
1.6.2. 1.6.2. Installation Configurations Installation Configurations
THE EXHAUST VENTING SYSTEM OF THIS UNIT. THE EXHAUST VENTING SYSTEM OF THIS UNIT. THE EXHAUST VENTING SYSTEM OF THIS UNIT.
, OR CEILINGS S S S . . . . , OR CEILING , OR CEILING
EVL equivalent(ft) EVL equivalent(ft) EVL equivalent(ft) EVL equivalent(ft)
5
3
1
0.5
e total vertical rise e total vertical rise e total vertical rise
CEILING/ROOF MUST BE MAINTAINED CEILING/ROOF MUST BE MAINT CEILING/ROOF MUST BE MAINT
FIGURE 10
Venting through wall
AINED AINED AINED