Related Manuals for Advantech PCI-7030
Summary of Contents for Advantech PCI-7030
- Page 1 User Manual PCI-7030 ® Intel ATOM N270 1.6GHz FSB533MHz, PCI Half-size SBC with Dual GbE LAN/LVDS/DVI/2 SATA/6 COM By Module...
- Page 2 No part of this manual may be reproduced, copied, translated or transmitted in any form or by any means without the prior written permission of Advantech Co., Ltd. Information provided in this manual is intended to be accurate and reliable. How- ever, Advantech Co., Ltd.
-
Page 3: Technical Support And Assistance
Whether your new Advantech equipment is destined for the labo- ratory or the factory floor, you can be assured that your product will provide the reliability and ease of operation for which the name Advantech has come to be known. -
Page 4: Declaration Of Conformity
Caution! There is a danger of a new battery exploding if it is incorrectly installed. Do not attempt to recharge, force open, or heat the battery. Replace the battery only with the same or equivalent type recommended by the man- ufacturer. Discard used batteries according to the manufacturer's instructions. PCI-7030 User Manual... - Page 5 (64x8) (RoHS) DDR2 ELPIDA E5108AGBG-6E-E (64x8) DDR2 ELPIDA E1108ACSE-6E-E (128x8) DDR2 TS128MSQ6 HYNIX HY5PS12821E-FP- 4V8J S5 (64x8) Transcend (RoHS) DDR2 TS256MSQ6 Micron D9HNP (128x8) 4V8U DDR2 ELPIDA TWN E5108AHSE-8E-E (64x8) (RoHS) DDR2 ELPIDA JPN E1108ACSE- 8E-E (128x8) PCI-7030 User Manual...
-
Page 6: Ordering Information
Because of Advantech’s high quality-control standards and rigorous testing, most of our customers never need to use our repair service. If an Advantech product is defec- tive, it will be repaired or replaced at no charge during the warranty period. For out- of-warranty repairs, you will be billed according to the cost of replacement materials, service time and freight. -
Page 7: Packing List
It should be free of marks and scratches and in perfect working order upon receipt. As you unpack the PCI-7030, check it for signs of ship- ping damage. (For example, damaged box, scratches, dents, etc.) If it is damaged or it fails to meet the specifications, notify our service department or your local sales representative immediately. - Page 8 PCI-7030 User Manual viii...
-
Page 9: Table Of Contents
Board layout: Jumper and Connector Locations ........5 Figure 1.1 Jumper and Connector Location ........ 5 Figure 1.2 I/O Connectors ............5 PCI-7030 Board Diagram................6 Figure 1.3 PCI-7030 Board Diagram ........... 6 Safety Precautions ..................7 Jumper Settings ..................8 1.8.1 How to Set Jumpers.............. - Page 10 . 55 Programming the Watchdog Timer ............56 A.1.1 Watchdog Timer Overview ............56 A.1.2 Programming the Watchdog Timer..........56 Table A.1: Watchdog Timer Registers........58 A.1.3 Example Program ............... 59 Appendix B I/O Pin Assignments ......61 PCI-7030 User Manual...
- Page 11 Table C.1: System I/O Ports ............72 DMA Channel Assignments ..............73 Table C.2: DMA Channel Assignments........73 Interrupt Assignments ................73 Table C.3: Interrupt Assignments..........73 1st MB Memory Map ................73 Table C.4: 1st MB Memory Map ..........73 PCI-7030 User Manual...
- Page 12 PCI-7030 User Manual...
-
Page 13: Chapter 1 General Information
Chapter General Information... -
Page 14: Introduction
The PCI-7030 series has an onboard ® CPU Intel Atom™ N270 1.6GHz procesor with 533 MHz front side bus and DDR2 533 MHz up to 2 GB. The PCI-7030 offers cost-saving integrated graphics, built ® ® on the Intel... -
Page 15: Graphics
Board weight: 0.365 kg Jumpers and Connectors Connectors on the PCI-7030 CPU card link it to external devices such as hard disk drives and a keyboard. In addition, the board has a number of jumpers used to con- figure your system for your application. -
Page 16: Table 1.2: Connetors
System FAN connector (3-pin) HDAUD1 High Definition audio connector GPIO1 GPIO pin header RTC battery connector DVI1 DVI connector LPC1 LPC connector SPI_CN1 SPI flash programming connector SPI flash socket SMBUS1 SM BUS connector LVDS1 LVDS connector INV1 Inverter connector PCI-7030 User Manual... -
Page 17: Board Layout: Jumper And Connector Locations
Board layout: Jumper and Connector Locations Figure 1.1 Jumper and Connector Location Figure 1.2 I/O Connectors PCI-7030 User Manual... -
Page 18: Pci-7030 Board Diagram
PCI-7030 Board Diagram Figure 1.3 PCI-7030 Board Diagram PCI-7030 User Manual... -
Page 19: Safety Precautions
Caution! There is a danger of a new battery exploding if it is incorrectly installed. Do not attempt to recharge, force open, or heat the battery. Replace the battery only with the same or equivalent type recommended by the man- ufacturer. Discard used batteries according to the manufacturer’s instructions. PCI-7030 User Manual... -
Page 20: Jumper Settings
A pair of needle-nose pliers may be helpful when working with jumpers. If you have any doubts about the best hardware configuration for your application, contact your local distributor or sales representative before you make any changes. Generally, you simply need a standard cable to make most connections. PCI-7030 User Manual... -
Page 21: Cmos Clear (Cmos 1)
Clear CMOS data 2-3 closed * Default 1.8.3 JLVD1: LCD Power 3.3 V/5 V Selector Table 1.4: JLV1/JLV2: LCD Power 3.3 V/5 V Selector Closed Pins Result 1-2* 3.3 V* *Default 3.3 V 2-3 closed 1-2 closed PCI-7030 User Manual... -
Page 22: Jwdt1: Watchdog Timer Output Option
System Memory The PCI-7030 series has one socket for a 200-pin SODIMMx1. This sockets use 1.8 V un-buffered double data rate synchronous DRAMs (DDR SDRAM). They are avail- able in capacities of 256, 512, and 1024 MB. The sockets can be filled in any combi- nation with DIMMs of any size, giving a total memory size between 256 MB and 2 GB. - Page 23 PCI-7030 User Manual...
- Page 24 PCI-7030 User Manual...
-
Page 25: Chapter 2 Connecting Peripherals
Chapter Connecting Peripherals... -
Page 26: Introduction
Front Panel Connectors (JFP1 & JFP2) There are several external switches to monitor and control the PCI-7030. IR Connector (JIR1) This connector supports the optional wireless infrared transmitting and receiving module. -
Page 27: Ide Connector (Ide1)
IDE channel. Floppy Connector (FDD1) You can attach one floppy drive to the PCI-7030. You can use any combination of 5.25” (360 KB and 1.2 MB) and/ or 3.5” (720 KB, 1.44 MB, and 2.88 MB) drives. PCI-7030 User Manual... -
Page 28: Parallel Port (Lpt1)
LPT1. USB Ports (USB12/USB34) The PCI-7030 provides up to four ports of USB (Universal Serial Bus) which gives complete Plug & Play and hot swapping for up to 127 external devices. The USB interface complies with USB Specification Rev. 2.0 supporting transmission rate up to 480 Mbps and is fuse protected. -
Page 29: Serial Ata Interface (Sata1, Sata2)
2.10 Serial Ports (COM12) The PCI-7030 offers two serial ports COM1 & COM2. These ports can connect to serial devices, such as a mouse or to a communications network. The IRQ and address ranges for all ports are fixed. However, if you want to disable the port or change these parameters later, you can do this in the system BIOS setup. -
Page 30: Ps/2 Keyboard / Mouse Connector (Kbms1 & 2)
Advantech) for connecting to both a PS/2 keyboard. 2.12 VGA Connector (VGA1) The PCI-7030 includes a VGA interface that can drive conventional CRT displays. VGA1 is a standard 15-pin D-SUB connector commonly used for VGA. Pin assign- ments for CRT connector VGA1 are detailed in Appendix B. -
Page 31: Lan Rj45 Connector (Lan12)
2.13 LAN RJ45 connector (LAN12) PCI-7030 uses the Intel 82574L Gigabit LAN chip which is linked to PCIe x1 Link. With this chip, PCI-7030 can provide high throughput for heavy load networking envi- ronments. It provides one or two RJ-45 connectors in the rear side and is convenient for most industrial applications. -
Page 32: Table 2.1: Front Panel Lan Indicator Connector
10Mbps Link Off 2.15 ATX Feature connector (ATXF1) The PCI-7030 can support an advanced soft power switch function, if an ATX power supply is used. To enable the soft power switch function: Get the specially designed ATX-to-EBX power cable Connect the 3-pin plug of the cable to ATXF1 (ATX feature connector). -
Page 33: Atx Power Control Connector (Atx1)
The PCI-7030 support ATX power. ATX1 supplies main power (+5V,+12V, 5VSB), and it is a 6 x 2 power connector 2.17 CPU FAN connector (CPUFAN1) The PCI-7030 is equipped with a 3-pin FAN connector providing +12 V power for CPU FAN. PCI-7030 User Manual... -
Page 34: System Fan Connector (Sysfan1)
The PCI-7030 is equipped with a 3-pin FAN connector providing +12 V power for system FAN. 2.19 Audio Interface Connector (HDAUD1) The Audio Interface link is a 10 pin connector, the PCI-7030 can support Audio with the addition of optional PCE-AUDIO-HDA1E. Detailed pin assignment refers to Appendix B. PCI-7030 User Manual... -
Page 35: Gpio Header (Gpio1)
PCs and Flat Panel Displays, Digital CRT displays, Projectors, and HDTV. The PCI-7030 is able to drive a DVI connector display at a pixel resolution up to maximum pixel lock of 400 MHz up to 2048 x 1536 resolutions @ 75 Hz, users can select display type and boot number from BIOS menu selection. -
Page 36: Low Pin Count Header (Lpc1)
2.22 Low Pin Count Header (LPC1) PCI-7030 provides a 14-pin pin-header for LPC module. Refer to Appendix B for detailed information on the pin assignments. Here are the LPC modules that you can choose. Table 2.2: LPC Module Part Number... -
Page 37: Lvds Connector (Lvds1)
2.24 LVDS Connector (LVDS1) For PCI-7030, LVDS1 consists of a 40-pin connector which can support 18/36-bit up to UXGA 1600 x 1200 2.25 LCD Inverter Connector (INV1) The LCD inverter is connected to INV1 via a 5-pin connector to provide power to the LCD display. - Page 38 PCI-7030 User Manual...
-
Page 39: Bios Operation
Chapter BIOS Operation... -
Page 40: Introduction
CPUs from 386 through Pentium and AMD Geode™, K7 and K8 (including multiple processor platforms), and VIA Eden C3 and C7 CPU. You can use Advantech’s utili- ties to select and install features to suit your design needs. BIOS Setup... -
Page 41: Main Menu
This setup page includes CPU host clock control, frequency ratio and voltage. Load Setup Defaults This setup page includes Load system optimized value, and the system would be in best performance configuration. Set Password Establish, change or disable password. PCI-7030 User Manual... -
Page 42: Standard Cmos Features
All, But Keyboard The system boot will not stop for a keyboard error; it will stop for all other errors. (Default value) Base Memory The POST of the BIOS will determine the amount of base (or conventional) memory installed in the system. PCI-7030 User Manual... -
Page 43: Advanced Bios Features
Setup setting default is enabled. First / Second / Third / Other Boot Drive Hard Disk Select boot device priority by Hard Disk. CDROM Select boot device priority by CDROM. USB-FDD Select boot device priority by USB-FDD. PCI-7030 User Manual... -
Page 44: Advanced Chipset Features
This “Advanced Chipset Features” page controls configuration of the board’s chipset. This page is chipset dependent; screens may differ somewhat depending on the chipset. It is strongly recommended that only technical users make changes to the default settings. PCI-7030 User Manual... - Page 45 This item allows the user to decide boot display mode. Panel Number This item allows the user to decide display resolution. Init Display First This item is the setting for start up video output: either from PCI Express or Onboard device. PCI-7030 User Manual...
-
Page 46: Integrated Peripherals
OnChip IDE Device This item enables users to set the OnChip IDE device status, including some of new chipsets also support SATA devices (Serial-ATA). PCI-7030 User Manual... - Page 47 When enabled, this field allows you to connect your floppy disk drives to the onboard floppy disk drive connector instead of a separate controller card. If you want to use a different controller card to connect the floppy disk drives, set this field to Disabled. PCI-7030 User Manual...
- Page 48 This item allows user to adjust serial port 10 of address and IRQ. This serial port 10 need to be provided by LPC module (optional) COM10 Auto Direction [Disable] This item allows user to enable Auto-Flow control function of COM10 if sup- ported. PCI-7030 User Manual...
-
Page 49: Usb Device Setting
Select “Enabled” if you plan to use a USB keyboard/Mouse. The choices are "Enabled" and "Disabled". USB Storage Function Select "Enabled" if you plan to use an external USB storage device to boot sys- tem under DOS mode. The choices are "Enabled" and "Disabled". PCI-7030 User Manual... -
Page 50: Security Chip Configuration (Optional Item)
Select an item and then press <Enabled> to display the configuration options. Note! To enable the TPM function, set the TPM Support item to [Enabled] and then save the change; after rebooting, the TPM configuration menu will show the active options. PCI-7030 User Manual... -
Page 51: Power Management Setup
Blank Screen This option only writes blanks to the video buffer. DPMS Initial display power management signaling. Video Off In Suspend [Yes] This item allows users to turn off video when system is in suspend mode. PCI-7030 User Manual... - Page 52 Use this to set up the system after power failure. The “Off” setting keeps the sys- tem powered off after power failure, the “On” setting boots up the system after failure, and the “Former-Sts” returns the system to the status before power fail- ure. PCI-7030 User Manual...
-
Page 53: Pnp/Pci Configurations
The commands here are “Auto(ESCD)” or “Manual”. Choosing “Manual” requires you to choose resources from the following sub-menu. “Auto(ESCD)” automatically configures all of the boot and Plug and Play devices, but you must be using Windows 95 or above. PCI-7030 User Manual... -
Page 54: Pc Health Status
This shows the current CPU temperature. SYSTEM Temperature This shows you the current temperature of system. FAN 1 Speed This shows the current FAN 1 operating speed. FAN 2 Speed This shows the current FAN 2 operating speed. PCI-7030 User Manual... -
Page 55: Frequency/Voltage Control
Spread Spectrum [Disabled] This item enables users to set the spread spectrum modulation. CPU Host/SRC/PCI Clock [Default] This item enables users to set the CPU Host and PCI clock by system automatic detection or by manual. PCI-7030 User Manual... -
Page 56: Load Setup Defaults
“Setup” requires a password only to enter Setup. “System” requires the pass- word either to enter Setup or to boot the system. A password can be at most 8 characters long. PCI-7030 User Manual... - Page 57 Select Set Password again, and at the “Enter Password” prompt, please don’t enter anything; just press <Enter>. At the”Confirm Password” prompt, again, don’t type in anything; just press <Enter>. Select Save to CMOS and EXIT, type <Y>, then <Enter>. PCI-7030 User Manual...
-
Page 58: Save & Exit Setup
Typing “Y” will quit the BIOS Setup Utility and save user setup values to CMOS. Typing “N” will return to BIOS Setup Utility. 3.2.16 Quit without Saving Note! Typing “Y” will quit the BIOS Setup Utility without saving to CMOS. Typing “N” will return to BIOS Setup Utility. PCI-7030 User Manual... -
Page 59: Chipset Software Installation Utility
Chapter Chipset Software Installation Utility... -
Page 60: Before You Begin
DVD content, and MPEG-2 motion compensation for software DVD Note! This utility is used for the following versions of Windows, and it has to be installed before installing all the other drivers: Windows 2000 Windows XP Windows Vista PCI-7030 User Manual... -
Page 61: Windows Xp Driver Setup
Windows XP Driver Setup Insert the driver CD into your system's CD-ROM drive. You can see the driver folder items. Navigate to the "Drv_INF" folder and click "infinst_autol.exe" to complete the installation of the driver. PCI-7030 User Manual... - Page 62 PCI-7030 User Manual...
-
Page 63: Vga Setup
Chapter VGA Setup... -
Page 64: Introduction
Insert the driver CD into your system's CD-ROM drive. You can see the driver folders items. Navigate to the "Drv_VGA" folder and click "setup.exe" to complete the instal- lation of the drivers for Vista, Windows XP, and Windows 2000. PCI-7030 User Manual... -
Page 65: Lan Configuration
Chapter LAN Configuration... -
Page 66: Introduction
Introduction The PCI-7030 has a dual Gigabit Ethernet LAN via dedicated PCI Express x 1 bus (Intel82574L), which offers bandwidth of up to 500 MB/sec, eliminating the bottleneck of network data flow and incorporating Gigabit Ethernet to operate at 1000Mbps. -
Page 67: Appendix A Programming The Watchdog Timer
Appendix Programming the Watchdog Timer... -
Page 68: Programming The Watchdog Timer
2F (hex) is the data port. You must first assign the address of register by writing an address value into address port 2E (hex), then write/read data to/from the assigned register through data port 2F (hex). PCI-7030 User Manual... - Page 69 Unlock IT8718F Select LDN=07h for watchdog timer Program the Watchdog Timer Control Register Lock IT8718F PCI-7030 User Manual...
-
Page 70: Table A.1: Watchdog Timer Registers
(hex). This number decides how long the watch- dog timer waits for strobe before generating an interrupt or reset signal. Writing a new value to this register can reset the timer to count with the AA (hex) ----- value. IT8718F. PCI-7030 User Manual... -
Page 71: Example Program
; Set timeout interval as 10 seconds and start counting mov al,74h out dx,al inc dx mov al,00h out dx,al mov dx,2eh mov al,73h out dx,al inc dx mov al, 0Ah out dx, al ;----------------------------------------------------------- mov dx,2eh ; Lock IT8718F mov al,0aah out dx,al PCI-7030 User Manual... - Page 72 PCI-7030 User Manual...
-
Page 73: Appendix B I/O Pin Assignments
Appendix I/O Pin Assignments... -
Page 74: Front Panel Connectors (Jfp1)
Table B.2: Panel Connectors (JFP2) Signal FAN Fail LED + FAN Fail LED - Thermal Fail LED + Thermal Fail LED - USB Ports (USB12/USB34) Table B.3: USB Ports (USB12/USB34) Signal Signal USB Data1- USB Data2- USB Data1+ USB Data2+ PCI-7030 User Manual... -
Page 75: Ir Connector (Jir1)
IR Connector (JIR1) Table B.4: IR Connector (JIR1) Signal IR_RX IR_TX Serial Ports (COM12) Table B.5: Serial Ports (COM12) Signal Signal DCD1 DSR1 RTS1 CTS1 DTR1 DCD2 DSR2 RTS2 CTS2 DTR2 PCI-7030 User Manual... -
Page 76: Ps/2 Keyboard / Mouse Connector (Kbms2)
PS2 keyboard data PS2 mouse data PS2 mouse clock LAN LED connector (LANLED1/LANLED2) Table B.7: LAN LED connector (LANLED1/LANLED2) Signal Signal LAN1_LINK/ACTIVITY# LAN1_1000# VCC3 LAN1_100# ATX Feature connector(ATXF1) Table B.8: ATX Feature connector(ATXF1) Signal 5V standby PS_ON# PCI-7030 User Manual... -
Page 77: Cpu Fan Connector (Cpufan1)
System FAN connector (SYSFAN1) Table B.10: System FAN connector (SYSFAN1) Signal FAN_PWM +12V FAN_TACH B.11 Audio Interface Connector (HDAUD1) 8 1 0 Table B.11: Audio Interface Connector (HDAUD1) Signal Signal ACZ_VCC ACZ_SYNC ACZ_BITCLK ACZ_SDOUT ACZ_SDIN0 ACZ_SDIN1 ACZ_RST# ACZ_12V PCI-7030 User Manual... -
Page 78: Gpio Header (Gpio1)
Table B.12: GPIO Header (GPIO1) Signal Signal GPIO1 GPIO5 GPIO2 GPIO6 GPIO3 GPIO7 GPIO4 GPIO8 B.13 DVI LCD panel connector (DVI1) Table B.13: DVI LCD panel connector (DVI1) Signal Signal TDC0- TDC0+ TLC- TLC+ TDC1- TDC1+ SC_DDC SD_DDC TDC2- HPDETT TDC2+ PCI-7030 User Manual... -
Page 79: Lvds Connector (Lvds1)
LVDS_VCC LVDS_VCC LVDS_VCC LVDS_VCC LVDS0_D0- LVDS1_D0- LVDS0_D0+ LVDS1_D0+ LVDS0_D1- LVDS1_D1- LVDS0_D1+ LVDS1_D1+ LVDS0_D2- LVDS1_D2- LVDS0_D2+ LVDS1_D2+ LVDS0_CLK- LVDS1_CLK- LVDS0_CLK+ LVDS1_CLK+ LVDS0_DDC_SC LVDS0_DDC_SD B.15 LCD Inverter Connector (INV1) Table B.15: LCD Inverter Connector (INV1) Signal +12V BACK_ON# Brightness PCI-7030 User Manual... -
Page 80: Sm Bus Connector (Smbus1)
Low Pin Count Header (LPC1) 8 1 0 1 2 1 4 1 1 1 3 Table B.17: Low Pin Count Header (LPC1) Signal Signal LPC_CLK LPC_LAD1 LPC_RST# LPC_LAD0 LPC_FRAME# +3.3V LPC_LAD3 LPC_LAD2 SERIRQ PWROK 5V Standby PCI-7030 User Manual... -
Page 81: Atx Power Control Connector (Atx1)
B.18 ATX power control connector (ATX1) Table B.18: ATX power control connector (ATX1) Signal Signal 5V Standby PSON# +12V B.19 VGA Connector (VGA1) Table B.19: VGA Connector (VGA1) Signal Signal CRT_VCCIN VGA_G VGA_B V_SDAT H-SYNC V-SYNC V_SCLK PCI-7030 User Manual... - Page 82 PCI-7030 User Manual...
-
Page 83: Appendix C System Assignments
Appendix System Assignments... -
Page 84: System I/O Ports
Diskette controller 3F8-3FF Serial port 1 CA0-CA7 Serial port 3 CA8-CAF Serial port 4 CB0-CB7 Serial port 5 CB8-CBF Serial port 6 C80-C87 Serial port 7 C88-C8F Serial port 8 C90-C97 Serial port 9 C98-C9F Serial port 10 PCI-7030 User Manual... -
Page 85: Dma Channel Assignments
1st MB Memory Map Table C.4: 1st MB Memory Map Addr. range (Hex) Device E0000h - FFFFFh BIOS D0000h - DFFFFh Unused C0000h - CFFFFh VGA BIOS A0000h - BFFFFh Video Memory 00000h - 9FFFFh Base memory PCI-7030 User Manual... - Page 86 No part of this publication may be reproduced in any form or by any means, electronic, photocopying, recording or otherwise, without prior written permis- sion of the publisher. All brand and product names are trademarks or registered trademarks of their respective companies. © Advantech Co., Ltd. 2009...
Need help?
Do you have a question about the PCI-7030 and is the answer not in the manual?
Questions and answers