Advertisement
Quick Links
Advertisement
Related Manuals for Da-Lite Curved Multi Format Imager
Summary of Contents for Da-Lite Curved Multi Format Imager
- Page 1 INSTRUCTION BOOK FOR Curved Multi Format Imager...
-
Page 2: Important Safety Instructions
Important Safety Instructions Pre-Installation When using your video equipment, basic safety precautions The screen will arrive in three separate cardboard boxes. One should always be followed, including the following: box will be very long and will house the 4.75” x 8.00” top and bottom main frame parts, the 1.50”... - Page 3 Da-Snap Frame Assembly 1. Inside each box the frame pieces will be individually paper 4. Unroll the screen on a clean surface. Do not use newspaper. wrapped and taped. Remove all paper from pieces. Place screen surface over the frame, and while holding the Do not use a utility knife to remove paper from pieces.
- Page 4 Curved Multi Format Imager Assembly 1. Lay frame pieces out on the floor or table as shown in Figure will slide into the frame channel. When sliding the bracket 2. The bottom frame assembly has the junction box attached into the top frame assembly, guide the slat roller carriage into to it.
- Page 5 Curved Multi Format Imager Assembly 4. Assemble bottom end of left frame assembly to end of Assemble right side of frame to top and bottom frame bottom frame assembly. The large L-bracket will slide into the assemblies. The two large L-brackets will slide into top and...
- Page 6 Curved Multi Format Imager Assembly ran through the spring. Run black steel wire tension cable 9. Route the two cable assemblies around motor bracket and plug the 3 wire male connector into the 3 wire female down around pulley at end and bring back towards the end.
- Page 7 Curved Multi Format Imager Assembly Clip Wire Tension Clip Safety Cable Cable To Eyebolt To Middle Eyebolt Insert Wire Between Brackets, Lower Safety Cable And Wrap Pinch Guard Passes Through Around Pulley Slat Bar Middle of Spring Figure 10 Black Knob...
- Page 8 Curved Multi Format Imager Installation – Wall Mount The screen is shipped with one wall hanger board. Two small 5. Align the wood guide of the board with the metal guide of brackets are included to hold the frame securely to wall the screen.
- Page 9 Multi Format Imager Wiring Diagram To connect power to unit locate junction box cover on bottom frame assembly. There will be two black screws holding the wiring box cover on as shown in Figure 13. 2. Install electrical connections. Make sure to review the wiring diagram for proper hook up as shown in Figure 14.
- Page 10 Multi Format Imager Wiring Diagram Connect IR eye to splitter for screen operation. IR eye shall be plugged into a QEYE port on the primary splitter as shown in Figure 15. NOTES: 6P4C 1.) 6P6C = 6 Pins 6 Conductor Wire RJ-14 Cable 2.) 6P4C = 6 Pins 4 Conductor Wire Primary Splitter...
- Page 11 Multi Format Imager Intermediate Stop Adjustment To adjust intermediate stopping positions make sure both 3. Once both masks are at the desired stopping position. Press masks are completely retracted into the frame. Press the left and hold Preset 1, Preset 2, Preset 3 or Preset 4 button on mask ">"...
- Page 12 Multi Format Imager Limit Travel Adjustment (Continued) 12. To adjust how far the mask travels outward towards the 6. Locate the two tactile buttons on the back of the switch. They are square silver with black round buttons as shown in middle of masking screen, press and hold the up tactile Figure 18.
-
Page 13: Troubleshooting
Troubleshooting Visit www.da -lite.com/products/product_videos.php to find us by email at info@da-lite.com or by phone at (800) 622-3737 or installation and troubleshooting videos and tutorials. You will also (574) 267-8101 with any troubleshooting questions. find a link to Live Chat for interactive support and you can contact... - Page 16 OF EQUIPMENT, OR FOR INCIDENTAL, DIRECT, OR CONSEQUENTIAL DAMAGES OF ANY NATURE. In the event that there is a defect in materials or workmanship of a Da-Lite product, you may contact our Sales Partners at PO Box 137, Warsaw, IN 46581-0137, (574) 267-8101, (800) 622-3737.
Need help?
Do you have a question about the Curved Multi Format Imager and is the answer not in the manual?
Questions and answers