Table of Contents
Advertisement
This Manual Is Designed to Make it as Easy as Possible for You to
Assemble, Install, Operate and Maintain Your Ceiling Fan
Tools Needed for Assembly
One stepladder
One wire stripper
One Phillips head screwdriver
Four 15-watt (max.) candelabra base bulbs
MATERIALS
Wiring outlet box and box connectors must be of type
required by the local code. The minimum wire would
be a 3-conductor (2-wire with ground) of the wire
size, to right:
For your convenience, check-off boxes are provided next to each step. As each step is completed, place
a check mark in the box. This will insure that all steps have been completed and will be helpful in finding
your place should you be interrupted.
WARNING
!
Do not install or use fan if any part is damaged or
missing. Call Toll-Free:
1-800-654-3545
WARNING
!
This product is designed to use only those parts
supplied with this product and/or any accessories
designated specifically for use with this product by
Emerson Electric Co. Substitution of parts or
accessories not designated for use with this product
by Emerson Electric Co. could result in personal
injury or property damage.
1. Open styrofoam unit containing fan. Remove upper
and center sections of styrofoam unit. Remove parts
and check to see that you have received the following:
a. One Fan Motor and Housing Assembly
b. One Motor Coupling Cover
c. One Ceiling Cover
d. Five Fan Blades
e. Five Flanges
f. Five Flange Medallions
g. One Hanger Ball/12" Downrod Assembly
h. One Hanger Bracket
i. One 6" Downrod
j. One Light Kit Assembly
k. One Light Kit Glass
l. One Switch Housing
m. One Decorative Downrod Cover
n. Four Decorative Scrolls
o. One Scroll Collar
p. One SW116 Fan/Light Wall Control
(transmitter) Includes Three Covers
q. One SW105 Receiver
r. One Loose Parts Bag Containing:
1. One 5/16-18 x 1/4" setscrew
2. One 5/32" hex wrench
3. Four 8-32 x 1-1/4" threaded studs
4. Four #8-32 knurled knobs
Unpacking Instructions
3
Installed Wire Length
Up to 50 ft.
50-100 ft.
WARNING
!
If you feel you do not have enough wiring knowledge or
experience, have your fan installed by a licensed
electrician.
5. Four #8 external tooth lockwashers
6. Five 12 Ga. wire connectors
7. One hairpin clip
8. One clevis pin
9. Twenty-one 10-32 x 10mm pan head
screws
10. Eleven #8-32 x 14mm oval head screws
11. Four #8-32 x 10mm flat head screws
12. Five #8-32 x 15mm flat head screws
13. One balancing kit
NOTE: Place the parts from the loose parts bags
in small containers to keep them from being lost.
If any parts are missing, contact your local
retailer or catalog outlet for replacement before
proceeding.
b.
h.
HI
HI
LIGHT
MED
MED
LOW
LOW
n.
REV
REV
FAN OFF
o.
Wire Size A.W.G.
14
12
a.
10-32 x 10mm PAN HEAD SCREW
(4 Per Blade)
10-32 x 10mm PAN HEAD SCREW
(4 Per Blade)
10-32 x 10mm PAN HEAD SCREW
(4 Per Blade)
10-32 x 10mm PAN HEAD SCREW
e.
(4 Per Blade)
c.
10-32 x 10mm PAN HEAD SCREW
(4 Per Blade)
BLADE
BLADE
FLANGE
FLANGE
ASSEMBLY
d.
BLADE
MEDALLION
FLANGE
FLANGE
ASSEMBLY
BLADE
MEDALLION
FLANGE
MEDALLION
FLANGE
MEDALLION
f.
i
.
j
.
g
.
m.
k
l
.
.
r.
p.
q.
U.L. Model No.: CF3200
FLANGE
ASSEMBLY
BLADE
FLANGE
ASSEMBLY
FLANGE
FLANGE
ASSEMBLY
MEDALLION
Advertisement
Table of Contents
