Chorus - Boss GT-001 Parameter Manual

COMMON
Knob Parameter Value
Page 1 (if TYPE is set to other than DUAL-S, DUAL-P, or DUAL-L/R)
1 ms–2000 ms,
DLY .TIM
[2]
(DELAY TIME)
BPM –
FEEDBAK
[3]
0–100
(FEEDBACK)
E .LEVE
[4] 0–120
(EFFECT LEVEL)
Page 2 (if TYPE is set to other than DUAL-S, DUAL-P, or DUAL-L/R)
HI .CUT
630 Hz–
[1]
12.5 kHz, FLAT
(HIGH CUT)
DIR .MIX
[4] 0–100
(DIRECT MIX)
PAN
Knob Parameter Value
Page 2
[2] TAP TIME
0–100%
DUAL-S, DUAL-P, DUAL-L/R
Knob Parameter Value
Page 2, 3 (if TYPE is set to DUAL-S, DUAL-P, or DUAL-L/R)
1:TIME 1 ms–1000 ms,
[1]
2:TIME
BPM –
1:F .BAK
(FEEDBACK)
[2] 0–100
2:F .BAK
(FEEDBACK)
1:HiCUT
(HIGH CUT)
630 Hz–
[3]
12.5 kHz, FLAT
2:HiCUT
(HIGH CUT)
1:LEVEL
[4]
0–120
2:LEVEL
Explanation
Adjusts the delay time.
* When set to BPM, the value
of each parameter will be
set according to the value of
the "MASTER BPM" specified
for each patch. This makes
it easier to achieve effect
sound settings that match
the tempo of the song.
* If, due to the tempo, the time
is longer than the range of
allowable settings, it is then
synchronized to a period
either 1/2 or 1/4 of that time.
Adjusts the volume that is
returned to the input. A higher
value will increase the number
of the delay repeats.
Adjusts the volume of the
delay sound.
This sets the frequency at
which the high cut filter begins
to take effect. When "FLAT" is
selected, the high cut filter will
have no effect.
Adjusts the volume of the
direct sound.
Explanation
Adjusts the delay time of the left channel
delay. This setting adjusts the L channel
delay time relative to the R channel delay
time (considered as 100%).
Explanation
Adjusts the delay time.
* When set to BPM, the value
of each parameter will be set
according to the value of the
"MASTER BPM" specified for
each patch. This makes it easier
to achieve effect sound settings
that match the tempo of the
song.
* If, due to the tempo, the time
is longer than the range of
allowable settings, it is then
synchronized to a period either
1/2 or 1/4 of that time.
Adjusts the amount of feedback of
the DELAY 1 (or DELAY 2). A higher
value will increase the number of
the delay repeats.
This sets the frequency at which
the high cut filter begins to take
effect. When "FLAT" is selected, the
high cut filter will have no effect.
Adjusts the volume of the DELAY 1
(or DELAY 2).
MODULATE
Knob Parameter
Page 3
MOD .RT
[1]
(MODULATION RATE)
MOD .DPT (MODULATION
[2]
DEPTH)

CHORUS

In this effect, a slightly detuned sound is added to the original
sound to add depth and breadth.
Knob Parameter Value
CHORUS
OFF, ON
ON/OFF
Page 1
Selection for the chorus mode.
MONO
STEREO1
[1] MODE
STEREO2
0–100,
[2] RATE
BPM –
[3] DEPTH 0–100
E .LEVEL
[4] 0–100
(EFFECT LEVEL)
Page 2
PRE .DLY
0.0 ms–40.0
[1]
ms
(PRE DELAY)
LO .CUT FLAT,
[2]
(LOW CUT) 20 Hz–800 Hz
630 Hz–
HI .CUT
[3]
12.5 kHz,
(HIGH CUT)
FLAT
DIR .MIX
[4] 0–100
(DIRECT MIX)
EFFECT
Value Explanation
Adjusts the modulation rate of
0–100
the delay sound.
Adjusts the modulation depth
0–100
of the delay sound.
Explanation
Turns this effect on/off.
This chorus effect outputs the same
sound from both L channel and R
channel.
This is a stereo chorus effect that
adds different chorus sounds to L
channel and R channel.
This stereo chorus uses spatial
synthesis, with the direct sound
output in the L channel and the
effect sound output in the R channel.
Adjust the speed of the chorus effect
for the high frequency range.
* When set to BPM, the value of each
parameter will be set according
to the value of the "MASTER BPM"
specified for each patch. This
makes it easier to achieve effect
sound settings that match the
tempo of the song.
* If, due to the tempo, the time is
longer than the range of allowable
settings, it is then synchronized to
a period either 1/2 or 1/4 of that
time.
Adjusts the depth of the chorus
effect.
* To use it for doubling effect, set the
value to 0.
Adjusts the volume of the effect
sound.
Adjusts the time needed for the
effect sound to be output after the
direct sound has been output. By
setting a longer pre delay time, you
can obtain an effect that sounds like
more than one sound is being played
at the same time (doubling effect).
This sets the frequency at which the
low cut filter begins to take effect.
When "Flat" is selected, the low cut
filter will have no effect.
This sets the frequency at which the
high cut filter begins to take effect.
When "FLAT" is selected, the high cut
filter will have no effect.
Adjusts the volume of the direct
sound.
19